Philips FC6148 Handheld Vacuum Cleaner User Manual

Philips FC6148 Handheld Vacuum Cleaner

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

General description (Fig. 1)

• A Detachable nozzle
• B Nozzle release button
• C Dust compartment
• D Dust compartment release button
• E Charging light
• F On/off slide with 2 speeds
• G Exhaust air openings
• H Adapter
• I Crevice tool
• J Charger
• K Brush tool
• L Filter unit
• 1 Outer filter
• 2 Inner filter with filter holder

Important: Read this user manual carefully before you use the appliance and save it for future reference.

Danger

• Never suck up water or any other liquid. Never suck up flammable substances and do not suck up ashes until they are cold.
• Never immerse the vacuum cleaner or the charger in water or any other liquid.

Warning

• Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
• Do not use the vacuum cleaner or the charger if it is damaged.
• The charger and its adapter cannot be replaced. If the charger or its adapter is damaged, the appliance must be discarded.
• If the cord of the adapter is damaged, it cannot be replaced and the adapter must be discarded.
• The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Caution

• Remove the adapter from the wall socket before you clean the charger.
• Only charge the vacuum cleaner with the charger supplied. During charging, the adapter feels warm to the touch. This is normal.
• Always switch off the vacuum cleaner after use.
• The voltage on the contact strips in the charger is low (max. 12 volts) and therefore not dangerous.
• Never block the exhaust air openings during vacuuming.
• Switch off the appliance when you recharge it.
• Always use the vacuum cleaner with the filter unit assembled.
• To avoid the risk of electric shock, be careful when you drill holes in the wall to attach the charger, especially close to a wall socket.
• Charge, store and use the appliance at a temperature between 5°C and 35°C.
• Do not dismantle or short-circuit the batteries. Protect the batteries from fire, heat and direct sunlight.

Electromagnetic fields (EMF)

• This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Preparing for use

Installing the charger

1. Attach the charger to the wall as shown in the figure. (Fig. 2) If you attach the charger to the wall, the space between the screw holes has to be 12cm.
2. You can also place the charger on a horizontal surface (e.g. a table or desk) (Fig. 3).
3. Wind excess mains cord around the reel in the back of the charger and pass the cord through the slot (Fig. 4). Charging the appliance
   • Charge the appliance for at least 16 hours before you use it for the first time.

Tip: If you are not going to use the appliance for a longer period of time, remove the adapter from the wall socket to save energy.

1. Make sure the appliance is switched off.
2. Put the adapter in the wall socket.
3. Place the vacuum cleaner on the charger (Fig. 5).
   • Make sure you place the opening in the back of the vacuum cleaner on the hook of the charger (Fig. 6).
   • 
   • The charging light flashes to indicate that the appliance is charging (Fig. 7).
   • The charging light is on continuously to indicate that the appliance

Using the appliance

1. Push the on/off slide forwards to switch on the appliance (Fig. 8).
   • If you want to use normal power, select speed 1.
   • If you want to use high power, select speed 2.
2. Push the on/off slide backward to switch off the appliance (Fig. 9).

Accessories

• The appliance comes with the following accessories:
  • a brush tool to clean delicate surfaces;
  • a crevice tool to vacuum corners or narrow gaps.
• Take the accessory you want to use from the charger.
• Attach the accessory to the nozzle of the appliance (Fig. 10).

Cleaning

• Never immerse the vacuum cleaner or the charger in water or any other liquid.
• Always remove the adapter from the wall socket before you clean the charger.
  • Clean the outside of the appliance and the charger with a damp cloth.
  • If the contact points of the charger are dirty, wipe them with a dry cloth.

Emptying and cleaning the dust compartment

Make sure you empty and clean the dust compartment regularly.

Quick cleaning

To empty the dust compartment quickly:

1. Press the nozzle release button (1) and take the detachable nozzle off the appliance (2) (Fig. 11).
2. Shake the contents of the dust compartment out into a dustbin (Fig. 12).

Thorough cleaning

1. Hold the appliance over a dustbin, press the dust compartment release button (1), and remove the dust compartment (2) (Fig. 13).
2. Remove the filter unit from the dust compartment (Fig. 14).
3. Empty the dust compartment by shaking it with your free hand (Fig. 15).
4. If necessary, clean the dust compartment with a damp cloth.
5. If necessary, clean the filter unit. See section ‘Cleaning the filter unit’.
6. To reattach the dust compartment, align the slot on the dust compartment with the projection on the appliance. First, attach the bottom of the dust compartment (1). Then push the top of the dust compartment towards the appliance (2) until it locks into place (‘click’) (Fig. 16).

Cleaning the filter unit

Make sure you clean the filter unit regularly.

1. Turn the outer filter anticlockwise (1) and remove it from the filter holder (2) (Fig. 17). Leave the inner filter attached to the filter holder.
2. Clean the inner filter and the outer filter with a brush or with a normal vacuum cleaner if they are very dirty.
   • Note: If necessary, you can clean the inner filter and the outer filter in cold or lukewarm water. Dry the inner and outer filters thoroughly before you use the filter unit again.
3. Place the outer filter back onto the filter holder (1) and turn it clockwise to attach it (2). (Fig. 18)
4. Put the filter unit back into the dust compartment (Fig. 19). Note: Make sure you correctly insert the filter unit.

Storage

1. You can store the vacuum cleaner and the accessories on the charger (Fig. 20).

Replacement

1. We advise you to replace the inner filter after a prolonged period of use or if you can no longer clean it properly.

Replacing the inner filter

1. Remove the filter unit from the dust compartment (Fig. 14).
2. Turn the outer filter anticlockwise (1) and remove it from the filter holder (2) (Fig. 17).
3. Gently turn the inner filter anticlockwise (1) and remove it from the filter holder (2) (Fig. 21).
4. Place a new inner filter on the filter holder (1) and turn it clockwise to attach it (2) (Fig. 22).
5. Push the tip of the inner filter inwards (Fig. 23).
6. Place the outer filter on the filter holder (1) and turn it clockwise to attach it (2). (Fig. 18)
7. Put the filter unit back into the dust compartment (Fig. 19). Note: Make sure you correctly insert the filter unit.

Accessories

1. New inner filters are available under type no. FC8035. Contact your Philips dealer.

Environment

1. Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 24).
2. The built-in rechargeable batteries contain substances that may pollute the environment. Remove the batteries when you discard the appliance. Do not throw away the batteries with the normal household waste, but hand them in at an official collection point. You can also take the appliance to a Philips service centre. The staff of this centre will remove the batteries for you and will dispose of them in an environmentally safe way (Fig. 25).

Removing the rechargeable batteries

1. Only remove the rechargeable batteries if they are empty. Never let the rechargeable batteries come into contact with metal. Remove the rechargeable batteries in the following way.
2. Let the vacuum cleaner run until it stops.
3. Try to switch on the appliance again to check if the batteries are empty. If the motor starts, repeat the procedure.
4. Loosen and remove the screws. Open the vacuum cleaner (Fig. 26). 3 Put the motor unit with the batteries still attached in a large bowl with 3 litres of water and 3 teaspoons of salt.
   • Make sure the whole motor unit is immersed. Add more water and salt according to the above proportion (1 teaspoon salt to 1 litre of water) if needed.
   • Leave the motor unit and the batteries in the bowl for 24 hours.
5. Cut the connecting wires one by one and remove the batteries (Fig. 27).

Guarantee & service

If you need service or information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Consumer Care Centre in your country, go to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Centre in your country.

• The appliance does not work.
  • The batteries may be low. Recharge the batteries.
  • You may not have placed the appliance on the charger properly. Place the appliance on the charger properly. The charging light goes on to indicate that the appliance is charging.
  • You may not have put the adapter properly in the wall socket. Put the adapter properly in the wall socket.
  • The contact points on the appliance and/or on the charger may be dirty. Wipe them clean with a dry cloth.
  • The appliance may have been switched on while it was on the charger. Make sure the appliance is switched off when you charge it.
  • If the appliance still does not work, take the appliance to your dealer or a service centre authorized by Philips for examination.
• The charging light does not go on.
  • Make sure that the adapter is inserted properly in the wall socket and that the appliance is switched off.
• The vacuum cleaner does not vacuum properly.
  • The dust compartment may not be attached properly to the appliance. Attach the dust compartment properly to the appliance.
  • The dust compartment may be full. Empty the dust compartment.
  • The filter unit may be clogged. Clean the inner filter and the outer filter (see chapter ‘Cleaning’).
• Dust escapes from the vacuum cleaner.
  • The dust compartment may be full. Empty the dust compartment.
  • The dust compartment may not be attached properly to the appliance. Attach the dust compartment properly to the appliance.
  • Perhaps the filter unit is not placed properly in the dust compartment. Place the filter unit properly in the dust compartment.
• The vacuum cleaner does not work properly when one of the accessories is attached to the nozzle.
  • The dust compartment may be full. Empty the dust compartment.
  • The accessory may be clogged. Remove the obstruction from the accessory.
  • The filter unit may be clogged. Clean the inner filter and the outer filter (see chapter ‘Cleaning’).

www.philips.com

Frequently Asked Questions

How do I charge the Philips FC6148 Handheld Vacuum Cleaner?

To charge the Philips FC6148 Handheld Vacuum Cleaner, plug the adapter into a wall socket, place the vacuum cleaner on the charger, ensuring it's properly aligned, and the charging light will indicate when it's charging.

Can I leave the Philips FC6148 Handheld Vacuum Cleaner on the charger all the time?

While you can leave the Philips FC6148 Handheld Vacuum Cleaner on the charger, it's advisable to remove the adapter from the wall socket if you're not using it for an extended period to save energy.

How long should I charge the Philips FC6148 Handheld Vacuum Cleaner before its first use?

Charge the Philips FC6148 Handheld Vacuum Cleaner for at least 16 hours before using it for the first time.

Can I use the Philips FC6148 Handheld Vacuum Cleaner while it's charging?

No, it's recommended not to use the Philips FC6148 Handheld Vacuum Cleaner while it's charging. Please ensure it's switched off during charging.

What are the two-speed settings on the Philips FC6148 Handheld Vacuum Cleaner?

The Philips FC6148 Handheld Vacuum Cleaner has two-speed settings - Speed 1 for normal power and Speed 2 for high power.

How do I switch off the Philips FC6148 Handheld Vacuum Cleaner?

To switch off the Philips FC6148 Handheld Vacuum Cleaner, push the on/off slide backward.

Can I use accessories with the Philips FC6148 Handheld Vacuum Cleaner?

Yes, the Philips FC6148 Handheld Vacuum Cleaner comes with accessories like a brush tool and a crevice tool for different cleaning needs.

How do I empty the dust compartment quickly on the Philips FC6148 Handheld Vacuum Cleaner?

To empty the dust compartment quickly on the Philips FC6148 Handheld Vacuum Cleaner, press the nozzle release button and remove the detachable nozzle. Shake the contents into a dustbin.

How do I perform a thorough cleaning of the dust compartment on the Philips FC6148 Handheld Vacuum Cleaner?

To thoroughly clean the dust compartment on the Philips FC6148 Handheld Vacuum Cleaner, remove it by pressing the dust compartment release button. You can then empty and clean it as needed.

How often should I clean the filter unit on the Philips FC6148 Handheld Vacuum Cleaner?

Clean the filter unit on the Philips FC6148 Handheld Vacuum Cleaner regularly to maintain performance. You can clean the inner and outer filters with a brush or cold/lukewarm water if they are very dirty. Ensure they are dry before using them again.

Where can I get replacement inner filters for the Philips FC6148 Handheld Vacuum Cleaner?

Replacement inner filters for the Philips FC6148 Handheld Vacuum Cleaner are available under type no. FC8035. You can contact your Philips dealer for these filters.

How should I dispose of the Philips FC6148 Handheld Vacuum Cleaner when I no longer need it?

Do not throw away the Philips FC6148 Handheld Vacuum Cleaner with normal household waste. Instead, hand it in at an official collection point for recycling to help preserve the environment.

What should I do if the Philips FC6148 Handheld Vacuum Cleaner is not working correctly?

f the Philips FC6148 Handheld Vacuum Cleaner has issues, such as not working, not vacuuming properly, or dust escaping, refer to the troubleshooting section in the user manual. If the problem persists, contact the Philips Consumer Care Centre or your local Philips dealer for assistance.

Download The PDF link:Philips FC6148 Handheld Vacuum Cleaner User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>