TECH Sinum FZ-02m Touch Glass Switch User Guide
- June 17, 2024
- TECH
Table of Contents
FZ-02m Touch Glass Switch
User Guide
Sinum FZ-02m Touch Glass Switch
The FZ-02m / WZ-02m roller shutter switch is a device for controlling roller
shutters with the use of the switch or the Sinum central device. Sinum allows
the user to program specific conditions for raising / lowering the roller
shutters. Communication with the Sinum central device is done by wire.
The FZ-02m / WZ-02m switch has a built-in light sensor which is used to adjust
the button backlight brightness to ambient light level.
IMPORTANT!
- Connecting the roller shutter to the switch outputs in reverse will result in incorrect operation of the device and incorrect calibration.
- Before using the switch for the first time, the roller shutter limit switches should be set correctly.
- After every ten movements of the roller shutter, automatic calibration takes place – the roller shutter moves to the extreme position and then returns to the set position.
- The roller shutter is controlled by constantly applying power supply to a given direction of roller shutter operation.
NOTE:
- Steps to follow after registering and adding the switch to the Sinum Central device, in the switch settings [Settings > Devices > SBUS Devices > (on the device tile)]:
- choose the type of blinds you have: blackout or tilting
- when choosing a tilting roller blind, you should also select the tilt angle: 90°3) perform calibration
- The tolerance between the height set in the Sinum application and the actual roller blind height level can be max. 5%.
- When a newer version of the device software is available [Settings > Update center > SBUS Devices], you can update it. lub 180°
CONTROL OF THE TILTING SHUTTER
While holding the roller shutter up/down button:
- less than 1.5 seconds – change the angle of the roller shutter elements
- over 1.5 seconds – change of the roller shutter opening level
How to register the device in the sinum system
The device should be connected to the Sinum central device using the SBUS
connector 2 , and then enter the address of the Sinum central device in the
browser and log in to the device. In the main panel, click the Settings >
Devices > SBUS devices > + > Add device. Then
briefly press the registration button 1 on the device. After a properly
completed registration process, an appropriate message will appear on the
screen. Additionally, the user can name the device and assign it to a specific
room.
How to identify the device in the Sinum system
To identify the device in the Sinum Central, activate the Identification
Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab
and hold the registration button on the device for 3-4 seconds. The device
used will be highlighted on the screen.
Technical data
Power supply | 24V DC ±10% |
---|---|
Max. power consumption | 1W |
Operation temperature | 5°C ÷ 50°C |
Rated load of the voltage-free contact 1-2 | 230V AC / 0,5A (AC1)* |
Installation | flush-mountable, electrical box ø60mm |
Communication with Sinum Central device | SBUS (TECH MODBUS) |
- AC1 load category: single-phase, resistive or slightly inductive AC load
Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website.
Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by hildren. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.
The product may not be disposed of to household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.
EU Declaration of conformity
Tech Sterowniki II Sp. z o.o. ul. Biała Droga 34, Wieprz (34-122)
Hereby, we declare under our sole responsibility that the FZ-02m/WZ-02m roller shutter switch is compliant with Directive:
• 2014/35/UE • 2014/30/UE • 2009/125/WE • 2017/2102/UE
For compliance assessment, harmonized standards were used:
- PN-EN 60669-1:2018-04
- PN-EN 60669-1:2018-04/AC:2020-04E
- PN-EN 60669-2-5:2016-12
- EN IEC 63000:2018 RoHS
Wieprz, 01.08.2023 The full text of the EU declaration of conformity and the user manual are available after scanning the QR code or at www.tech- controllers.com/manuals
TECH STEROWNIKI II Sp. z o.o.
ul. Biała Droga 31
34-122 Wieprz
tel: +48 33 875 93 80 www.tech-controllers.com
support.sinum@techsterowniki.pl
www.techsterowniki.pl/manualswww
.tech-controllers.com/manuals
Made in Poland
References
- controllers.com
- Intelligens fűtés-hűtés, fűtési-hűtési megoldások - TECH vezérlők gyártója | TECH vezérlők
- Sinum - TECH Controllers
- Intelligent heating, smart heating solutions - manufacturer of controllers | TECH Controllers
- Manuals - TECH Controllers
- TECH Controllers - Teplo ve Vašem domě
- TECH Controllers - Teplo vo Vašom dome
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>