ergotron MLDKYCG Dock Locker Instruction Manual
- June 17, 2024
- ERGOTRON
Table of Contents
MLDKYCG Dock Locker
ASSEMBLY
INSTRUCTIONS
Dock Locker for Microsoft Surface Pro 3 and Docking Station
Product …………..Part#
Dock Locker …………….MLDKYCG
NOTE: Shown with Microsoft Surface Pro 3 and Docking Station, not
included.
Anthro Corporation®
10450 SW Manhasset Dr.
Tualatin, OR 97062
Toll-free: 800.325.3841
Fax: 800.325.0045
email:sales@anthro.com
anthro.com
Outside the U.S.
Tel: 503.691.2556
Fax: 503.691.2409
January 2015
Anthro is a registered trademark and brand of Ergotron, Inc. (c) 2015.
Ergotron Inc. is a Nortek Company 
WELCOME
Thank you for purchasing the Dock Locker for Microsoft Surface Pro 3 Docking
Station.
If you have any questions or if we can help you in any way, please contact us
at 800.325.3841.
TOOLS
A power drill and drill bit (either 1/4″ or 1/8″ depending on your
installation method) may be required for this assembly.
A Phillips screwdriver and 3/8″ socket or nut driver may also be required.
These tools are included with your shipment:
5/32″ hex driver bit
5/32″ hex Anthro driver
3-way wrench
KEYS
For replacement keys, order part number 979KY.
PARTS LIST
Before beginning installation of your Dock Locker, please review the parts
list to verify that your shipment is complete.
The fastener quantities listed are the minimum required to complete the
installation. Your shipment may have included extras.
| Product | Quantity | Part Number |
|---|---|---|
| 01 Locker Assembly | 1 | 835-MLD |
| A. Top Cap | 1 | 225-4931-00 |
| B. Bottom Plate | 1 | 225-4957-00 |
| 02 #10-24 x 2.5″ Bolt | 2 | 325-5747-00 |
| 03 #10-24 Nylock Nut | 2 | 325-5186-00 |
| 04 #10-9 x1″ PB Screw (not shown) | 2 | 325-5580-00 |
STEP 1 – SET THE DOCK LOCKER IN PLACE AND OPEN IT
- Select the installation location for your locker. Provide at least 5″ of clearance behind the unit.
- Place the unit in its spot and open it. To unlock the unit, insert the key and turn. To open the unit, push the button on the lock and lift the cover back.
- IF YOU WILL SECURE YOUR LOCKER TO THE WORKSURFACE USING A BOLT-THROUGH OR SCREW-MOUNT METHOD, GO TO STEP 2.
- IF YOU WILL SECURE YOUR LOCKER TO THE WORKSURFACE WITH A SECURITY CABLE, OR IF YOU WILL NOT SECURE YOUR LOCKER, GO TO STEP 3.
STEP 2 – SECURE YOUR DOCK LOCKER WITH SCREW-MOUNT OR BOLT-THROUGH METHOD.
- Locate the two round installation holes near the back of the bottom plate. Mark the holes. Set aside the unit.
- Pre-drill the holes. For screw-mount installation, use a 1/8″ drill bit to drill 1/2″ into the worksurface. For bolt-through installation, use a 1/4″ drill bit to drill all the way through the worksurface. For added security for your cords and cables, you can route them through the cord pass-through opening in the base plate. To use that pass-through, mark and drill an opening in your worksurface now.
- Attach the unit to the worksurface. For screw-mount installation, fasten the unit to the worksurface with two 1″ PB screws (325-5580-00) using your drill and the Anthro driver bit provided. For bolt-through installation, slide one bolt (325-5747-00) through each hole in the bottom plate and through the worksurface. Capture with the #10-24 Nylock Nut (325-5186-00).
STEP 3 INSTALL YOUR DOCK AND SURFACE PRO 3 DEVICE
- Close the Locker. Feed the cords through the locker (either through the worksurface and into the bottom of the locker or through the back of the locker. Connect cords to the docking station. Slide the docking station into the locker and gently pull excess cord length out of the locker. Slide the dock into place in the locker so the front of the dock rests just behind the lockers front lip, and the dock nests into the indentation in the bottom plate.
- Fit your Surface Pro 3 device into the dock. Press the side tabs closed so they fit securely into your device.
- Test the fit. First, slowly pull forward on the lock to close the unit. The top grip will slide over the top of the screen, and the cover will enclose the side tabs.
- Next, press the lock button and slowly open the unit. Check that the top grip releases the top of your screen. Check that the cover releases the side tabs on the dock.
- If you are using a security cable, install it now through the port on the top of the cover.
PORT
GUIDE
| A | USB 3.0 |
|---|---|
| B | Audio |
| C | Gigabit Ethernet |
| D | USB 3.0 |
| E | USB 3.0 |
| F | USB 2.0 |
| G | USB 2.0 |
| H | Mini-display Port |
| I | Power |
| J | Security Lock Slot |
CONGRATULATIONS! YOUR ANTHRO LOCKER INSTALLATION IS COMPLETE!
Anthro is a registered trademark and brand of Ergotron, Inc. (c) 2015.
Ergotron Inc. is a Nortek Company.
| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: 800.325.0045 | email:
sales@anthro.com | anthro.com
Ergotron Inc.
Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409
Warranty:
This Dock Locker has a Lifetime Warranty against manufacturing defects.
Notices:
Anthro™ and Technology Furniture™ are trademarks of Ergotron Inc.,
a Nortek Company, and reserves the right to modify the design and
specifications without prior notice.
Microsoft and Surface are trademarks of the Microsoft group of companies.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>