Extron SMK V SB 33 Plus VESA Mounting Kit Installation Guide
- June 17, 2024
- Extron
Table of Contents
SMK V SB 33 Plus VESA Mounting Kit
Installation Guide
SMK V SB 33 Plus VESA Mounting Kit
Important: Go to www.extron.com for the complete
user guide, installation instruction and specification before connection the
product to the power source.
The SMK V SB 33 Plus VESA Mounting Kit allows the SB 33 Series of soundbar
speakers to be attached to the same VESA mount supporting the display device.
The SB 33 speaker front surface can be adjusted flush with the front of the
display. It can be adjusted forward, backward, up, down, and side-to-side.
Installation
VESA display mounts come in a variety of different styles, so installation may
vary. Please consult the installation guides for your specific VESA display
mount and your display device before installing the SMK V SB 33 Plus VESA
mounting kit. Follow the steps below to install the kit.
WARNING: Risk of personal injury or property damage. The final
installation should be able to continuously support the speaker weight. The
final installation should also be able to support short term overloading. Be
sure to not exceed the load limit of the VESA mount, mounting surface, and SMK
V SB 33 Plus. The maximum load limit of the SMK V SB 33 Plus is 85 lb (38 kg).
Since applications can vary considerably, it is assumed that the installer
will exercise good judgment when selecting the mounting location, method, and
hardware. Installation and service must be performed by authorized personnel
only.
NOTE: Observe all applicable building codes and local ordinances when
installing a soundbar speaker.
The SMK V SB 33 Plus VESA mounting kit is composed of 2 long L-brackets, 2
short L-brackets, 4 metal washers/spacers, 4 plastic spacers, 6 bolts, 6 lock
washers, and 6 wingnuts.
- Install the wall mount portion of the VESA display mount onto the desired wall location.
- Position one long L-bracket of the SMK V SB 33 Plus kit on the back of the display, while aligning the bottom bolt hole on the display with a round hole on the L-bracket and the top bolt hole with one of the slotted holes.
NOTE: The L-bend of the long bracket should align with the bottom of the display device. Repeat this procedure for the other long L-bracket on the other side of the display. Use the included plastic spacers if any portion of the display back panel protrudes further than the VESA mounting points and prevents the brackets from being seated properly.
NOTE: The long L-brackets are designed to accomodate a variety of display heights. If the bracket is exposed over the top of the display, the top 8″ (203 mm) of the SMK V SB 33 Plus long L-bracket can be broken off. To do this, simply bend the top breakaway portion back at the seam until it breaks off. (see figures 1 and 2 for details).
-
Place the VESA display mount on top of the L-bracket, while aligning the bolt holes of the display mount with the bottom round hole and top slot hole of the L-bracket and the bolt hole of the display. Repeat this procedure for the other long L-bracket on the other side of the display.
NOTE: If the VESA display mount uses horizontal mounting brackets or a X-braced bracket, then insert the included four metal washer/spacers between the long L-bracket and VESA display mount. -
Insert bolts through the VESA display mounts, the long L-brackets, and the display. Be sure to align the bolt holes of the VESA display mounts with the display mounting holes and insert the bolts. Hand tighten all 4 bolts. Spacers are provided if needed (see figure 1 on the previous page).
-
Position the short L-bracket under the long L-bracket so that the L-bends of each bracket are paired together (see figure 3).
Afterwards, install one bolt with a wingnut and lock-washer so that the long and short L-brackets are held together. Tighten the wingnut.
Repeat this procedure for the other long L-bracket on the other side of the display.
NOTE: The short L-bracket may be reversed if the soundbar needs to be positioned further forward relative to the display (see figure 3).
-
Install the SB 33 speaker wall plate to the short L-bracket using two bolts, two lock washers, and two wingnuts as shown in figure 4.
Repeat this procedure for the other short L-bracket on the other side.
-
Tighten the bolts and permanently fasten the display onto the VESA wall mount previously attached in figure 2.
-
To adjust the SB 33 speaker vertically:
a. Loosen, but do not remove, the bolts that attach the long L-brackets to the display.
b. Adjust the SB 33 to the desired distance from the display and then tighten the bolts.
NOTE: Assuming the display screen is
level, allow for some space between the bottom of the display screen and the
top of the speaker because the speaker assemblies and the center bracket
attach to the wallplate by hooking the top mounting clasps of the speaker
assemblies and center bracket over the top mounting rail of the wall plate.
To allow sufficient clearance between the top of the SB 33 speaker and the display screen above it, allow for at least a minimum clearance of 11/16 inches (17.5 mm) between the highest part of the top rail of the wallplate and the top of the speaker, as shown to the right. The display screen should not encroach into this area above the top rail.
The long L-brackets for the SMK V SB 33 Plus have holes for the lower VESA holes. As a result, it may be necessary to remove the lower bolts in order to adjust the vertical height. Depending on the short L-bracket orientation and depth adjustment, it is also possible to adjust the SB 33 speaker height by adjusting the wall bracket position on the short L-bracket. -
Install the SB 33 speaker to the wall plate as shown in figure 6.
-
If the alignment between the display and the SB 33 speaker needs to be adjusted in order to align the front of the speaker assembly relative to front of the display, do the following:
a. Loosen, but do not remove, the two wingnuts attaching the long L-brackets to the short L-brackets.
b. Adjust the soundbar speaker to either the front or the rear of the display and then tighten the wingnuts.
-
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2020 Extron Electronics — All rights reserved.
www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805,
800.633.9876
https://manual-hub.com/
68-3104-51 Rev. A
03 20
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>