Extron DA2 HD 4K Distribution Amplifier User Guide
- June 17, 2024
- Extron
Table of Contents
DA2 HD 4K Distribution Amplifier
User Guide
DA2 HD 4K Distribution Amplifier
DA2 HD 4K • Setup Guide
IMPORTANT: Go to www.extron.com for the complete user guide and installation instructions before connecting the product to the power source.
Overview
The Extron DA2 HD 4K distribution amplifier distributes one HDMI input signal
to two outputs simultaneously (following the HDMI 1.4 specification at
resolutions up to UHD and 4K). This setup guide provides basic instructions
for installation by an experienced installer. For complete instructions, see
the DA HD 4K Series User Guide at
www.extron.com.
Front Panel
A Power status LED — Lights green when power is applied to the unit.
B USB Config port — Used for SIS™ configuration, monitoring, and firmware
updates.
C Input Signal LED — Lights green when a TMDS signal is detected on the
HDMI input.
D Output Signal LEDs — Light green when HPD is detected from the
corresponding sink device and when a TMDS signal is detected at the input.
E Input HDCP LED — Lights green when the source requires HDCP encryption
and it has been authenticated with the HDMI input.
F Output HDCP LEDs — Light green when HDCP is authenticated between the
DA2 HD 4K output and the corresponding sink device.
Rear Panel
A Power input — Connect the provided 12 VDC power supply to this two-pole
captive screw connector.
ATTENTION:
• Do not connect the power supply before reading the Attention in the Power
Supply section of the DA Series HD 4K User Guide.
B HDMI input — Connect a source device to this female HDMI type A
connector.
C HDMI outputs — Connect up to two display devices to these female HDMI
type A connectors.
D RS-232 — Used for SIS configuration, monitoring, and firmware updates
(Pin 1 = Tx, Pin 2 = Rx, Pin 3 = Ground). Protocol: 9600 baud, 8 data bits, 1
stop bit, no parity.
Installation
-
Mount the DA2 HD 4K in a suitable location (see www.extron.com for mounting options). Follow the instructions
provided with the mounting kit. -
If required, connect a control PC to the USB Config port (Front Panel B on the previous page) or RS-232 connector (Rear Panel D on the previous page). To connect the rear panel RS-232 connector to a PC, ensure that the PC transmit connects to the RS-232 receive and the PC receive connects to the RS-232 transmit (see the diagram below).
NOTE: Use SIS commands to configure EDID Minder® , mute the video signal, mute the audio signal, adjust the video color bit depth, or monitor the signal and HDCP status. See the “SIS Commands” section of the DA HD 4K Series User Guide. -
Connect the display devices to the rear panel HDMI outputs and power them on. Connect the primary display to output 1. EDID from output 1 is stored automatically.
NOTE: Use the LockIt ® HDMI cable lacing brackets provided to secure the HDMI connectors.
Follow these instructions to secure the input and output HDMI connectors to the unit with the LockIt HDMI lacing bracket provided: a. Plug the HDMI cable into the panel connection ( 1 ).
b. Loosen the HDMI connection mounting screw from the panel enough to allow
the LockIt lacing bracket to be placed over it ( 2 ). The screw does not have to be removed.
c. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the screw to secure the bracket ( 3 ). ATTENTION:
• Do not overtighten the HDMI connection mounting screw. The shield it fastens to is very thin and can easily be stripped.
d. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown ( 4 ).
e. While holding the connector securely against the lacing bracket, tighten the tie wrap, then remove any excess length. -
Connect the provided 12 VDC power supply to the 2-pole captive screw connector. ATTENTION:
• Do not connect the power supply before reading the Attention in the Power Supply section of the DA Series HD 4K User Guide. -
Connect and power on the source device.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2015-2018 Extron Electronics — All rights reserved.
www.extron.com
All trademarks mentioned are the property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>