HEARTLAND IF-1336TCL Electric Stove Heater Instruction Manual

HEARTLAND IF-1336TCL Electric Stove Heater

Product Information

Specifications:

• Model No.: IF-1336TCL
• Power Cord: 2-flat blades (live and neutral) and 1 round pin (ground)

Product Usage Instructions

Safety Precautions

Before using the electric fireplace, it is important to follow these safety precautions:

• Read and understand the user manual completely.
• Avoid storing or using flammable liquids near the appliance.
• Connect the fireplace to properly grounded outlets only.
• Do not insert any foreign objects into ventilation or exhaust openings.
• Avoid blocking air intakes or exhausts.
• Never leave the heater unattended and always unplug when not in use.
• Do not use the fireplace if it has become wet.
• Check the outlet for any loose wires or connections before plugging in the heater.

Preparation

Before installation, follow these steps:

1. Handle the glass panel with extreme caution to avoid personal injury or property damage.
2. Remove all parts and hardware from the packaging, placing them on a clean, dry surface.
3. Ensure that all necessary tools are available: Phillips screwdriver, stud finder, level, tape measure, electric drill, 1/4 wood drill bit, and hammer.
4. Check the parts list to ensure nothing is missing.
5. Dispose of packaging materials properly and consider recycling whenever possible.

Installation

Follow these steps to install the electric fireplace:

1. Choose a suitable location for the fireplace, ensuring proper clearance from flammable materials.
2. Use a stud finder to locate and mark the position of the wall studs.
3. Place the fireplace against the wall and use a level to ensure it is straight.
4. Mark the location of the mounting holes on the wall.
5. Drill pilot holes using a 1/4 wood drill bit.
6. Securely attach the fireplace to the wall using the provided screws.

FAQ

Q: Can I use the fireplace without mounting it on the wall?

A: Yes, the fireplace can be used without mounting it on the wall. However, ensure that it is placed on a stable and heat-resistant surface.

Q: How do I clean the electric fireplace?

A: To clean the fireplace, unplug it and use a vacuum to remove any dust or debris. Do not rinse or get the unit wet.

Q: Can I use the fireplace overnight?

A: It is not recommended to leave the fireplace unattended or use it overnight. Always unplug the unit when not in use.

Q: What should I do if the outlet or face plate becomes hot?

A: Discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

Model No.: IF-1336TCL

CONSUMER SAFETY INFORMATION

• Read this manual before installing and operating this appliance
• Failure to follow these instructions may result in electric shock, fire property, or personal injury
• Do not store or use gasoline or other flammable liquids in vicinity of this appliance.

Web: https://clihome.net/
Service Contact : service@clihome.net
Phone Number: 951-213-4743 / 303-747-4421

IMPORTANT SAFETY INFORMATION!

WARNING

• Read all instructions before using this heater!
• This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner, Discard heater, or return to authorized service facility for examination and /or repair.
• DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.

WARNING

• Connect to properly grounded outlets ONLY.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust openings, as this may cause electric shock or fire, or damage the heater.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• ALWAYS plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
• DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact with water.
• AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other Blockage.Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
• ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other surface, to use.
• NEVER use a wall mount bracket from another manufacturer.
• This product is not intended to be a primary heat source. It is for supplemental heat only.
• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
• ALWAYS turn this heater off before unplugging it from the outlet.
• ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.
• NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
• ALWAYS store this heater in a dry location.NEVER use the fireplace if it has become wet.
• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.
• ALWAYS check your heater cord and plug connections with each use!

1. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
2. Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
3. During use check frequently to see if the plug outlet or face plate is HOT!
4. If the outlet or face plate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

The power cord supplied with the heater has a plug with two flat blades (live and neutral) and one round pin (ground). If a 3- slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right).(Note:Adapter NOT INCLUDED.)
SAVE THESE INSTRUCTIONS!

PREPARATION

This product includes a GLASS panel! Always use extreme caution when handing glass. Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grounded for wall-hanging or recessing use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape measure; electric drill; 1/4” wood drill bit, hammer.

PARTS & HARDWARE

Specification and Dimension

PRODUCT DIMENSIONS

91.5cm

| 17.0”

43.2cm

| 4.13”

10.5cm

| 32.2”

81.8cm

| 16.2”

41.2cm

| 9.1”

23.2cm

| 29.7”

75.4cm

Installation and Assembly

Your appliance is a wall-mounted, recessed and /or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.
NOTE：Follow all National and local electrical codes.

MINIMUM CLEARANCE TO COMBUSTIBLES

Sides

Back

| 0”

0”

| Top| 11.8”(300mm) to ceiling

MINUMUM MANTEL CLEARANCES

WARNING
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE HEAT RESISTANT TO PREVENT DISCOLOURATION

RECESSED TO WALL INSTALLATION

STEP A. Selection a dry wall to open a hole for fireplace box. Size of hole as below chat Figure (A)

Framing Hole Size

Model Number| W| H
IF- 1336TCL| 32.77(83.2cm)| 16.54”(42.0cm)

STEP B. Fix the four wall anchors in each side of the fireplace box according to the dimensions Showed on the drawing. Figure (B)

STEP C. Take off the two screws in both sides of fireplace. Figure (C)
STEP D. Have two person to take the glass panel out of the fireplace box. Place it to a soft and clean place. Figure (D) , taks two pcs of foam out of fireplace(E).

STEP E. Have two person to move the fireplace box to the wall hole or fireplace mantel (F). If the appliance is fully recessed into the wall:

• Use the 4 screws(provided) to lock the appliance into wall with the existing two side flanges, see Figure(G)
• Install the media and re-install the glass front.

STEP F. Place the front panel lock the appliance. See Figure (H)
STEP G. Fireplace will be like this after installation Figure (I)

Logset /Crystal Ember Installation

(Note: Please make the installation according to the embers which you bought or selected.)

• A. Glass front must be removed and the appliance must be mounted in its final location before the logset/crystal embers are installed.
• B. If your fireplace come with lotset, remove the logset from the package, put it to the fireplace designed place. Figure 1.
• C. If your fireplace come with CLEAN CRYSTAL MEDIA: crystal may have a fine oil residue that needs to be cleaned prior to installation. Clean them with mild dish soap, drain, rinse thoroughly and dry before placing into the tray.
• D. Then carefully place crystal embers into the bottom tray on the front of the appliance as illustrated. Apply an even layer from side to side. Figure 2.

WARNING

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure do to so could result in electric shock, fire, serious injury, or death.

Power
Plug the power cord into a 110-120V Volt 12 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.

Methods of Operation
This electric fireplace can be operated by the TOUCH PANEL, located on the BOTTOM right side glass panel of the fireplace, or by the battery-powered REMOTE CONTROL.
The operation and functions of the two methods are the same.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, and heed all warnings.

Touch panel/Remote control Operation

NOTICE
When the heater is first turned on, a slight odor may be odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time.

NOTICE
To improve operation, aim the remote control at the front of the fireplace. DO NOT press the buttons too quickly.Give the unit time to respond to each command.

Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically turn OFF. To reset:

1. Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
4. With the POWER switch in the OFF position, plug the power cord back into the outlet.
5. If the problem continues, have your outlet and wiring inspected by a professional.

Remote Control Battery Information

With 2x AAA batteries.

• Step1, remove back cap .
• Step 2, take back cap out off remote, insert 2x AAA batteries.
• Last, fasten back cap again.

NOTE: Remote control battery used depends on the remote control type which selected above.

NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

CARE AND MAINTENANCE

Cleaning

ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.

Metal

• Buff using a soft cloth, slightly dampened with a citrus oil-based product.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim.

Glass

• Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
• Clean the exterior of the fireplace with a slightly damp cloth or duster.

Maintenance

• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
• ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Electrical and Moving Parts

• The fan motors are lubricated at the factory and will not require lubrication.
• Electrical components are integrated in the fireplace and are not serviceable by the consumer.

Storage:

Store heater in a clean dry place when not in use.

WARNING! No other servicing should be performed by the consumer. Do not attempt to service the unit yourself.

Troubleshooting

WARNING
DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE.
ONLY A QUALIFIED SEVICE PERSON SHOULD SERVICE AND PEPAIR THIS ELECTRIC APPLAINCE.

and safety devise has caused thermal switch to disconnect

or home circuit breaker has opened.

| 1. Reset switch by turning main power off and waiting turning it back on or breaker circuit breaker.
2. Flame is not moving.| 1.  Loose wiring.

2.  Flame motor defective.

3.  Flame rod out of place

| 1.  Inspect wiring for loose connections.

2.  Call a qualified service technician to replace flame motor.

3.  “Flame Rod” out of place due to rough transit/handing of the product. This issue can be corrected as simple as removing the glass, flipping the fireplace upside and down, removing a set of screws that are holding the bottom frame plate and placing the flame rod back into place.

---|---|---
3 Flame is not visible.| 1. Wiring is loose| 1.  Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary.

2.  Push the flame button to high

4 Log set and /or is not glowing.| 1.  Wiring is loose

2.  Ember is off mode

| 1. Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary.
5 Remote control does not work.| 1.  Low batteries.

2.  Not aiming control correctly.

__

__

3.  Defective remote control and /or sensor

| 1.  Replace batteries in remote control.

2.  Aim control at sensor located directly behind glass screen in center of unit just above logs.

3.  Replace remote control and/or sensor.

References

• Clihome®- ALIPU INC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>