HEARTLAND IF-1336TCL Electric Stove Heater Electric Fireplace User Manual

HEARTLAND IF-1336TCL Electric Stove Heater Electric Fireplace User Manual

IMPORTANT SAFETYINFORMATION!

WARNING

• Read all instructions before using this heater!
• This heater is hot when in use.
• To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, suchasfurniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalidsandwhenever the heater is left operating and unattended.
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner, Discard heater, or return to authorized service facility for examination and /or repair.
• DO NOT run power cord under carpeting.
• DO NOT cover power cord with throw rugs ,runners, or similar coverings.
• DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.

WARNING

• Connect to properly grounded outlets ONLY.

• DO NOT insert or allow foreign objects to enter any ventilation or exhaust openings, as this may cause electric shock or fire, or damage the heater.

• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner.

• Doings could cause a fire.

• DO NOT use on soft surfaces, like a bed, where openings may become blocked.

• A heater has hot and arcing or sparking parts inside.

• DO NOT use it in area swheregasoline, paint, or flammable liquids are used or stored.

• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

• ALWAYS plug heaters directly into a wall outlet/receptacle. Never usewi than extension cord or relocatable power tap (outlet/power strip).

• DO NOT place the heater near a bed because objects such as pillows or blanketscanfall off the bed and be ignited by the heater.

• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact whitewater.

• AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other Blockage. Unplug the unit and clean with a vacuum ONLY.

• DO NOT rinse or get wet.

• ALWAYS mount to wall bracket before use.

• DO NOT set on the floor, or other surface, tousle.

• NEVER use a wall mount bracket from another manufacturer.

• • This product is not intended to be a primary heat source. It is for supplemental heat only.

• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electricshock!

• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
  ALWAYS turn this heater off before unplugging it from the outlet.

• ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.

• NEVER leave this heater unattended.

• ALWAYS unplug this heater when not infuse.

• ALWAYS store this heater in a dry location.

• NEVER use the fireplace if it has becomewet.

• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing with in the outlet that could cause the outlet to overheat or catch fire.

• ALWAYS check your heater cord and plug connections with each use!

  1. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
  2. Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
  3. During use check frequently to see if the plug outlet or face plate is HOT!
  4. If the outlet or face plate is HOT, discontinue use immediately and have qualified electrician inspect and/or replace the faulty outlets.

• The power cord supplied with the heater has a plug with two flat blades (live and neutral) and one round pin (ground). If a 3- slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right). (Note: Adapter NOT INCLUDED.)

• SAVE THESE INSTRUCTIONS!

PREPARATION

**** This product includes a GLASS panel! Always use extreme caution when handing lass. Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grounded for wall-hanging or recessing use. Check the parts list to measure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. You will need the following tools (not included): Phillips screwdriver; studfinder; level ;tape measure; electric drill; 1/4” wood drill bit, hammer.

PARTS & HARDWARE

• a. Fireplace

• b. 4x12mm Screws 4pcs

• c. Remote control

• d-Log set

• f-Decorative Crystals ( 1bag)

Specification and Dimension

T PRODUCT DIMENSIONS

Installation and Assembly

Your appliance is a wall-mounted, recessed and /or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.

NOTE: Follow all National and local electrical codes.

MINUMUM MANTEL CLEARANCES

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT ORLACQUERMUSTBE HEAT RESISTANT TO PREVENT DISCOLOURATION

RECESSED TO WALL INSTALLATION

STEP A. Selection a dry wall to open a hole for fireplace box. Size of hole as below chat Figure (A)

Figure (A) Framing Hole Size

Framing Hole Size

Model Number| W| H
IF-1336TCL| 32.77(83.2cm)| 16.54”(42.0cm)

IF-1336TCL Figure (B )

STEP B. Fix the four wall anchors in each side of the fireplace box according to the dimensions Showed on the drawing. **Figure (B

STEP C. Take off the two screws in both sides of fireplace. Figure (C)
STEP D.** Have two person to take the glass panel out of the fireplace box. Place it to a soft and
clean place. Figure (D) , taks two pcs of foam out of fireplace(E).

STEP E. Have two person to move the fireplace box to the wall hole or fireplace mantel (F). If the appliance is fully recessed into the wall:

• Use the 4 screws(provided) to lock the appliance into wall with the existing two side flanges, see Figure(G)

• Install the media and re-install the glass front.

STEP F. Place the front panel lock the appliance. See Figure (H)

STEP G. Fireplace will be like this after installation Figure (I)

Logset /Crystal Ember Installation

(Note: Please make the installation according to the embers which you bought or selected.)

• A. Glass front must be removed and the appliance must be mounted in its final location before the logset/crystal embers are installed.

• B. If your fireplace come with latest, remove the logset from the package, put it to the fireplace designed place . Figure 1.

• C. If your fireplace come with CLEAN CRYSTAL MEDIA: crystal may have a fine oil residue that needstobe cleaned prior to installation. Clean them with mild dish soap, drain, rinse thoroughly and dry before placing in to the tray.

• D. Then carefully place crystal embers into the bottom tray on the front of the appliance as illustrated. Applyan even layer from side to side. **Figure 2.

**

WARNING

Read and understand this entire owner’s manual, including all safety information, before plugs in ginner using this product. Failure do to so could result in electric shock, fire, serious injury, or death.

Power

Plug the power cord into a 110-120V Volt 12 Amp grounded outlet (see IMPORTANTS AFETY INFORMATION on Pages 2 and 3).Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances in to the same circuit.

Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and3, and heed all warnings.

Touch panel/Remote control Operation

effect. OFF: Disables    control     panel    functions           and remote control. Tum off flame effect.|

1. Press once. Indicator light turns on. Power turns on. All functions enabled.
2. Press again. Indicator light turns off. Power turns on. All functions will off.

| Coal bed COLOR button: Makes the coal bed’s color flame effect changing.|

1. Press once. Flame color effect gets changing.
2. Press again until desired setting is reached.

COLOR
FLAME| FLAME COLOR button: Makes the back flame color effect changing.|

1. Press once. Flame color effect gets changing.
2. Press again until desired setting is reached.

HEATER| HEATER button :Tum heater on and off.
NOTE: To prevent overheating, the heater fan will blow out cool air for 30 seconds after the heater turn off.|

1. Press once. Indicator lights up. 750W heater turns on and blows warm air.
2. Press again. Indicator lights up. 1500W heater, turns on and blows hot air.
3. Press again. Heaters turn off. The display shop,
4. The fan blows cool air for 30 seconds to allow heater to cool down, then turns off.

TEMP.| TEMPERATURE button: Control temperature settings to choose temperature as desired. Setting range from 62F to 82F.|

1. Press once. Indicator light turn on. Temperature is set to 62F.
2. Press again until desired setting is reached. LED display show setting.

TIMER| TIMER button: Control timer settings to turn off fireplace at selected time. Settings range from 0 hours, hours, to 8 hours.| 3. Press once. Indicator light turn on. Temperature is set to hours. Press again until desired setting is reached. LED display show setting.

NOTICE

When the heater is first turned on, a slight odor may be odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time.

NOTICE

To improve operation, aim the remote control at the front of the fireplace. DO NOT press the button stood quickly. Give the unit time to respond to each command.

Temperature Limiting Control

This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically turn OFF. To reset:

1. Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If the yare, use a vacuum to clean the vent areas.
4. With the POWER switch in the OFF position, plug the power cord back into the outlet.
5. If the problem continues, have your outlet and wiring inspected by a professional.

Remote Control Battery Information

• With 2x AAA batteries.

Step1, remove back cap.

Step 2, take back cap out off remote, insert 2x AAA batteries.

Last, fasten back cap again.

NOTE: Remote control battery used depends on the remote control type which selected above.

NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

CARE AND MAINTENANCE

Cleaning

ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could resulting electric shock, fire, or personal injury.

NEVER immerse in water or spray with water. Doing so could result unelectric shock, fire, or personal injury.

Metal:

• Buff using a soft cloth, slightly dampened with a citrus oil-based product.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim. Glass:
• Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface. Vents:
• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
• Clean the exterior of the fireplace with a slightly damp cloth or duster.

Maintenance

**** Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!

ALWAYS turn the heater OFF and unplug the power cord from the out let before cleaning, performing maintenance, or moving this fireplace. Failure to do so could resulting electric shock, fire, or personal injury.

Electrical and Moving Parts:

• The fan motors are lubricated at the factory and will not require lubrication.
• Electrical components are integrated in the fireplace and are not serviceable by the consumer.

Storage:

• Store heater in a clean dry place when not in use.

WARNING! No other servicing should be performed by the consumer. Do not attempt toservice the unit yourself.

Troubleshooting

WARNING

DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SEVICE PERSON SHOULD SERVICE AND PEPAIR THIS.

1. Fireplace has overheated and safety devise has caused thermal switch to disconnect or home circuit breaker has opened.

|

1. Reset switch by turningmainpower off and waiting turningitback on or breaker circuit breaker.

Flame is not moving|

1. Loose wiring.
2. Flame motor defective.
3. Flame rod out of place

|

1. Inspect wiring for loose connections.
2. all a qualified service technician to replace flame motor

Flame is not visi|

1. Wiring is loose

| 3. “Flame Rod” out of place due to rough transit/handing of the roduct. This issue can be corrected as simple as removing the glass, flipping the fireplace upsideanddown, removing a set of screws that are holding the bottom frame plate and placing the flame runback into place
Log set and /or is not glowing|

1. Wiring is loose
2. Ember is off mode

|

1. Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary.

Remote control does not work.|

1. Low batteries.
2. Not aiming control correctly.
3. Defective remote control and /or sensor

|

1. Replace batteries in remote control.
2. Aim control at sensor located directly behind glass screen incenter of unit just above logs.
3. Replace remote control and/orsenso

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>