PERFECT RF24G Remote Control User Manual

PERFECT RF24G Remote Control

Product Information

Specifications:

• Model: RF Wireless Remote Advanced RGB LED Controller
• Dynamic Modes: 213
• Static Colors: 256
• Smooth Effects: Very smooth
• Speed Adjustable: Yes
• Brightness Adjustable: Yes
• Type: RF Remote (Instructions Card Type)
• Design: Ultra Slim
• Dynamic Demo Mode: Yes
• Remote Pairing: Easy remote pairing
• Direct Color Select: Yes
• Automatic Mode: Yes
• Stop Brightness: Yes
• Turn on/Standby Dynamic SpeedA Mode: Yes
• Static Color Adjustment: Yes
• Timing Function Locked: Yes
• Timing Function Unlock: Yes
• Scene Mode: Yes

Product Usage Instructions

Using Remote Controller:
Please pull out the battery-insulated tape before using the remote controller. The 2.4G remote signal can pass through barriers, so it’s not necessary to aim at the main unit when operating.

Free Remote Pairing Mode:
In some specific cases, the main unit may need to be paired with any remote controllers. Please follow these steps for free remote pairing mode:

1. Plug off the power of the main unit.
2. Wait for a few seconds.
3. Plug in the power of the main unit.

Switch Output Color Sequence:
The controller’s default output signal sequence is 1sCommon-Green-Red-Blue. If the LED application is in a different cable sequence, the direct colour keys will not match the LED colour. In this case, the user can adjust the output signal sequence.

Remote Controller Functions:

• Press On/Standby to enter the standby state.
• Press Pause to pause automatic mode (21 default dynamic mode cycles).
• Press Speed/Sensitivity to increase or decrease the speed.
• Press Mode Switching to switch between modes.
• Press Brightness to increase or decrease the brightness.
• Press Switch the light colour to select the desired colour (red/green/blue/yellow/cyan/purple/white).
• Press Turn off the lights regularly to set a timer for turning off the lights after 1 or 2 hours.
• Press Locked/Unlock to lock or unlock the timing function.
• Press Switch respectively to switch between different models: snowflake/romantic/starry sky model.

Note:
When adjusting the brightness, if the speed is set to a high value, the light will flash to indicate that it has been adjusted to the maximum or minimum state.

Frequently Asked Questions (FAQ)

• Q: What should I do if the remote control does not work?
  A: Please check the following:

  • Make sure the battery-insulated tape has been removed.
  • Ensure the battery is properly inserted with the correct polarity.
  • Check if any barriers are obstructing the line of sight between the remote control and the main unit.
  • Try replacing the battery with a new one.

• Q: How can I reset the controller to its default settings?
  A: To reset the controller to its default settings, you can unplug the power of the main unit and plug it back in after a few seconds.

  • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Overview

• 213 Dynamic Modes
• 256 Static Colors
• Very Smooth Effects
• SpeedAdjustable
• Brightness Adjustable
• Card Type RF Remote
• Ultra Slim Design
• Dynamic Demo Mode
• Easy remote pairing
• Direct Color Select

Operation manual of remote controller

1. Using Remote Controller;
   Please pull out the battery-insulated tape before using it. The 2.4G remote signal can pass through a barrier, so it’s not, necessary to aim at the main unit when operating.

2. Free Remote Pairing Mode;
   In some specific cases, the main unit may need to be paired with any remote controllers. Please do the following steps for free remote pairing mode: Plug off the power of the main unit and plug-in after seconds.

3. Switch Output Color Sequence;
   The controller’s default output signal sequence 1sCommon-Green-Red-Blue.If the LED application is in a different cable sequence, the direct colour keys will not match the LED colour. ln this case, the user can adjust the output signal sequence.

Note:
Adjust the brightness, when the speed is large, the light flashes to indicate that it has been adjusted to the maximum or minimum state.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

This device has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>