J-TECH DIGITAL JTECH-HT4K70 HD BaseT HDMI Extender 4K Reciever User Manual
- June 17, 2024
- J-TECH DIGITAL
Table of Contents
J-TECH DIGITAL JTECH-HT4K70 HD BaseT HDMI Extender 4K Reciever
Product Information
Specifications :
- HDMI INPUT: Input HDMI signal
- IR IN: Connect to IR receiver extension cable
- IR OUT: Connect to IR blaster extension cable
- RS232: RS232 Serial interface
- DC12V: Input DC12V power
- HDBT OUT: Output HDBaseT signal
Product Usage Instructions
Source Equipment:
The product is designed to work with various HDMI source devices such as
computer graphics cards, DVD players, PS3, HD monitoring equipment, etc.
Display Devices:
The product can be connected to display devices that have an HDMI INPUT port,
including SDTVs, HDTVs, and projectors.
Network Cables:
Use UTP/STP CAT5E/CAT6/CAT6A/CAT7 network cables that follow the IEEE-568B
standard to connect the transmitter and receiver.
LED Indicator
The LED on the device indicates the power status and connection status:
- The LED will turn on once the transmitter and receiver are connected.
- The LED lights up when there is an HDMI input and the display device has an image.
Thank you for purchasing this product. For optimum performance and safety, please read the instructions carefully and keep the manual for future reference.
Important safety notice
Please read below safety instructions carefully before installation and
operation:
- Please pay attention to all the warnings and hints on this device.
- Do not expose this unit to rain, moisture and liquid.
- Do not put any stuff into the device.
- Do not repair or open this device without professional people’s quidance.
- Make sure good ventilation openings to avoid product overheating damage.
- Shut off power and make sure environment is safe before installation.
- Do not plug-in/out the connected cables when it is in using.
- Make sure the specification matched if using 3rd party DC adapters.
Introduction
This HDBaseT single network cable extender transmits HDMI signal up to 70 meters over cat fluently and clearly. It is lossless in signal and supports 3D,24bits deep color, CEC and HDCP. Support ultra HD 4Kx2K @60Hz. This product supports power over CAT cable, connect the power adapter either into the Transmitter unit or into the Receiver unit, and both can keep this device working normally. However, it is recommended to power from the Receiver unit.
Features
- Apply HDBaseT extend the technology
- Uncompressed HDMI video signal
- Support ultra HD 4K×2K@60Hz 4:2:0
- Extend 1080p signal over cat6a up to 70 meters
- Support bi-directional IR pass-back
- RS232 command pass-through
- Support HDCP, CEC, 24 deep
- Support uncompressed LPCM audio and compressed DTS-HD, Dolby True HD
- Can be powered by network cable. It only needs to input 12V power for either transmitter or receiver for normal working
Package contents
Installation Requirements
-
Source equipment :
HDMI source device (computer graphics card, DVD, PS3, HD monitoring equipment etc). -
Display devices:
With HDMI INPUT port, SDTV, HDTV, projector -
Network cables:
UTP/STP CAT5E/CAT6/CAT6A/CAT7 network cables, which following the standard of IEEE-568B
Panel description
HDMI to HDBaseT TX Transmitter
- HDMI INPUT : Input HDMI signal.
- IRIN : Connect to IR receiver extension cable.
- IR OUT : Connect to IR blaster extension cable.
- R$232 : RS232 Serial interface.
- DC12V: Input DC12V power.
- HDBT OUT: Output HDBaseT signal.
HD BaseT to HDMI RX Receiver
- DC12V: Input DC12V power.
- HDBT OUT : Output HDBaseT signal.
- HDMI INPUT: Input HDMI signal.
- IRIN : Connect to IR receiver extension cable.
- IR OUT: Connect to IR blaster extension cable.
- RS232: RS232 Serial interface.
LED indicators’ working status
- To indicate the power status of the device.
- The LED will on once transmitter and receiver are connected.
- The LED lights up when there is HDMI input and the display has an image.
Installation procedures
To make a Cat5e/6 network cable
Follow the standard of EFF_568B
Connections
NOTE : It is recommended to power from the Receiver unit. 6.3 Bi- directional IR pass back
- It supports bi-directional IR passback. The user can control the DVD at TX end and control TV at RX end.
- If control at RX end, please connect IR blaster extension cable with IR OUT of TX and connect IR receiver extension cable with IR IN of RX. If control at TX end, please connect IR receiver extension cable with IR IN of TX and connect IR blaster extension cable with IR OUT of RX.
Specification
Disclaimer
The product name and brand name may be registered trademark of related
manufacturers. TM and ® may be omitted on the user manual. The pictures on the
user manual are just for reference, and there may be some slight difference
with the real products. We reserve the rights to make changes without further
notice to a product or system described herein to improve reliability,
function or design.
- Product pictures are for reference only.
- Specifications described herein are subject to change without prior notification.
- All trademarks are the sole property of their respective companies.
- Copyright ©J-Techdigital, Inc. All rights reserved.
FAQ’S
What type of HDMI source devices are compatible with this product?
This product is compatible with various HDMI source devices such as computer graphics cards, DVD players, PS3, HD monitoring equipment, etc.
Can I connect product to a projector?
Yes, you can connect this product to a projector as long as the projector has an HDMI INPUT port.
What type of network cables should I use?
Use UTP/STP CAT5E/CAT6/CAT6A/CAT7 network cables that follow the IEEE-568B standard.
How can I know if the device is powered on and connected properly?
The LED on the device will turn on once the transmitter and receiver are connected. It will also light up when there is an HDMI input and the display device has an image.
No image output?
Check the led indicator status to make sure all connections are good and stable.
Signalled
Check the HDMI display device has been switched to the right HDMI input channel.
Check whether the TX's HDMIIN has signal input and make sure RX's HDMI OUT is well connected with HDMI display.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>