GOLD MEDAL 3052-00-001 Auto Breeze EZ Kleen Head Instruction Manual

GOLD MEDAL 3052-00-001 Auto Breeze EZ Kleen Head

Product Information

Specifications:

• Model No: 3052-00-001
• Part No: 110026
• Manufacturer: Gold Medal Products Co.
• Address: 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
• Website: https://manual-hub.com/

Safety Precautions:

DANGER: Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

DANGER: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

WARNING: Floss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection.

WARNING: Keep all foreign objects out of floss head. To avoid eye injury, DO NOT fill floss head with sugar while the head is on and rotating.

WARNING: Burn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or servicing. Avoid contact with molten sugar.

WARNING: ALWAYS wear safety glasses when servicing this equipment.

WARNING: No user serviceable parts inside.
Refer servicing to qualified service personnel.

WARNING: Read and understand operator’s manual
and all other safety instructions before using this equipment. To
order copies of the operator’s manual go to gmpopcorn.com or write
to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH
45241 USA 1-(800)-543-0862

WARNING: DO NOT allow direct contact of this
equipment by the public when used in food service locations. Only
personnel trained and experienced in the equipment operation may
operate this equipment. Carefully read all instructions before
operation.

WARNING: This machine is NOT to be operated by
minors.

Installation Instructions

Inspection of Shipment: After unpacking (reference unit Quick Start Guide), check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit or damage caused by abuse or consequential damage due to the operation of this machine since it is beyond our control (reference warranty in the back of the manual).

FAQ

Q: Can I immerse any part of the equipment in water?

A: No, you should not immerse any part of the equipment in water. This could result in electrical shock or damage to the equipment.

Q: Can I make alterations to the equipment?

A: No, any alterations to the equipment will void the warranty and may cause a dangerous condition. It is important to read the Installation, Operating, and Maintenance Instructions thoroughly before making any changes.

Q: Can minors operate this machine?

A: No, this machine is not to be operated by minors.

Q: Where can I order copies of the operator’s manual?

A: You can order copies of the operator’s manual by visiting gmpopcorn.com or writing to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA. You can also contact them at 1-(800)-543-0862.

Auto Breeze® EZ Kleen Head
Model No. 3052-00-001

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

© 2018 Gold Medal Products Co.

SAFETY PRECAUTIONS

Note: Improvements are always being made to Gold Medal’s equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only.

INSTALLATION INSTRUCTIONS

Inspection of Shipment
After unpacking (reference unit Quick Start Guide), check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual).

Manual
Read and understand the operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Model Description

3052-00-001: Auto Breeze cotton candy machine with EZ Kleen Head and an aluminum floss pan.

Items Included with this Unit

Setup for Use

(General reference images shown)

Whirlgrip Floss Stabilizer

Installation Instructions
Unit must be OFF, and cool to install Floss Stabilizer. Place Floss Pan on unit and install Whirl Grip Floss Stabilizer (Item No. 3010) as shown below. Kit includes: Floss Stabilizer/screening (P/N 43032), and (6) Whirlgrip Clips (P/N 77470). Clips are designed to provide air space between screening and floss pan.

Electrical Requirements

The following power supply must be provided:

3052-00-001: 120 V~, 1440 W, 60 Hz

A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.

Before You Plug In Machine

1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.

OPERATING INSTRUCTIONS

Controls and Their Functions (3052 Auto Breeze)

• POWER SWITCH
  Two position, ON/OFF lighted rocker switch – supplies power to the Candy Switch. The green switch light ON indicates there is power to the unit.
  Immediate Power Off: To bypass the cooling cycle and immediately remove power from the machine, turn the Power Switch OFF.

• CANDY SWITCH
  Two position, “White” rocker switch – turns the motor and heating element ON/OFF.
  When turned OFF, the cooling cycle will start. After one (1) minute the cooling cycle completes, and the spinner head will stop rotating. Cooling is necessary to keep carbon from forming in the spinner head.

• AUTO COOLING INDICATOR LIGHT
  When lit, this amber light indicates the unit is in the cooling cycle. During the cooling cycle the spinner head will remain spinning.
  If the Auto Cooling Light is blinking during machine operation, it indicates there is a low voltage supply to the machine (less than 105 VAC). The machine may not operate properly (see Troubleshooting section of this manual).

Sugar for Your Candy

• Ready to Use Flossugar
  Our ready to use Flossugar is the preferred sugar for your new cotton candy machine; however 100% pure cane or beet sugar will do just fine. Our Flossugar gives you good rich colors, and great flavors, too. It is packed in handy half-gallon sealed cartons, with an E-Z pour spout for filling your machine. Flossugar comes in many flavors, and you can easily change flavors for greatest variety, and best sales.

• Mix Your Own
  If you want to mix your own, use our Flossine®, and please follow our directions. If you want a deeper color, slightly dampen the mixed sugar. Use a tablespoon of water per five pounds of sugar, sprinkle water over sugar, and mix well. DO NOT USE EXCESS COLOR! Too much color will ruin the element on your machine and could create a bitter taste to the candy. There is a limit as to how dark you can make cotton candy. That’s because cotton candy is 98% air, and we cannot color the air.

• Sugar Considerations

  • Today 99% of the sugar manufactured is extra fine granulated, which does have some small particles which can slip thru the ribbons without being melted. If this becomes objectionable, you can seek out medium coarse or sanding sugars. The larger crystal size will require a little more heat to melt.
  • Read the label on the bag of sugar, today we see some free flowing sugars for restaurants. Free-flowing sugars contain cornstarch which will burn onto your element/band clogging them rapidly. We have also seen some off-brand sugars that are a blend of sugar and dextrose or corn syrup. This product makes very poor cotton candy. Please make sure you get good sugar for your cotton candy machine.

Machine Operation

Floss Machine Operation (3052 Auto Breeze)

1. Follow the guidelines described in the Electrical Requirements Section for supplying power to machine.

2. With the Candy Switch OFF, turn the Power Switch ON. The spinner head will not start to rotate.

3. With the spinner head stopped, pour flossugar into the spinner head. Always fill it 90% full with sugar. This 90% level is necessary to obtain a balanced condition in the floss head. DO NOT OVERFILL!
   IMPORTANT: NEVER add sugar when motor is running.

4. Turn the Candy Switch ON. The spinner head will rotate and heat. After about 30 seconds the machine will start to make cotton candy.

5. When the spinner head needs to be refilled with sugar, or to stop making cotton candy, turn the Candy Switch OFF. The cooling cycle will start. After 1 minute the cooling cycle completes, and the spinner head will stop rotating. When the spinner head is stopped, refill with flossugar. Turn the Candy Switch ON, and continue to make cotton candy.
   Note: During the cooling cycle the spinner head will remain spinning. Cooling is necessary to keep carbon from forming in the spinner head. DO NOT use the Power Switch for normal operation of the machine. This will bypass the cooling cycle.
   IMPORTANT: Failure to cool down the floss head could result in leaving melted sugar in the floss head. If the motor is restarted, this melted sugar will exit the floss head and could cause burns.
   In addition, sugar left in the floss head may smoke or cause carbon build up.
   Immediate Power Off: To bypass the cooling cycle and immediately remove power from the machine, turn the Power Switch OFF.

When completing operation for the day (or any prolonged period), follow the instructions in the Shutdown Procedure/Cleaning and Care section of this manual.

Making Floss

Pick a cone, if it sticks in the stack of cones, twist it off the stack.

Hold an inch or two of the pointed end of a cone between two fingers and a thumb. With a light flicking action, roll cone in the web of floss building up in the pan. Lift the cone up with the ring of floss attached and rotate the cone to wrap the floss. DO NOT roll floss while the cone is inside the pan. This will pack the floss too tightly. See steps 1 thru 8 shown below.
If the floss fails to stick to the cone, pass the cone near the spinner head to pick up a “starter” of melted sugar. Lift the cone out of the pan and wrap the floss with a “figure eight” movement of the hand. This leaves giant pockets and makes the final product appear larger. Make sure room humidity is not too high, or product will be “heavy”.

Rubber Float Adjustment

In operation, the floss will collect on the FLOSS STABILIZER. If the floss collects “low” on the stabilizer, twist the front (leading) edge of the rubber floats down (as shown below). This creates a lifting action to float the floss higher on the wall of the floss pan.
Be sure the rubber floats are fully inserted in the float holders on the Quick Release Floss Cap
(see image below).

Shut Down Procedure/ Care and Cleaning

Shut Down Procedure (3052 Auto Breeze)

1. When completing operation for the day (or any prolonged period), run the floss head completely empty of sugar.
2. Turn the Candy Switch OFF. The cooling cycle will start. When the cooling cycle completes, the spinner head will stop rotating.
3. When the spinner head is stopped, turn the Power Switch OFF.
4. NEVER put water in the floss head.

Care and Cleaning

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product.
Follow the directions below to clean and sanitize the unit each day after use.

1. Unplug the machine and wait for the floss head to cool down to room temperature.
2. Make sure to clean all pans/accessories in order to sanitize them before each use.
3. Wipe all surfaces with a clean, damp cloth.
4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
   DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine.

Floss Band and Element

Disassembly and Removal of Floss Band

1. Unplug the machine from the power source and allow floss head to cool completely.
2. Remove all sugar from the head of the machine before disassembling. If needed, carefully turn the machine on its side and shake the sugar out.
3. Rotate the Quick Release Floss Cap clockwise to unlock, then lift cap off of the floss head retaining bolts (see image below).
4. Remove the Take-Apart Spinner Cap.
5. Unscrew the ball knob counterclockwise and remove. This knob secures the terminal lock.
6. Lift off the terminal lock which fastens the element lead wires.
7. Lift the two (2) element lead wires off the power studs, then the band and element can be removed from the spinner head.
8. If there is excessive sugar build-up, run hot water over band and element until the sugar dissolves (be careful to keep element leads dry). When the sugar has been removed, allow the band and element to air dry overnight.
   Note: For models with separate heat and motor switches, the best way to dry the floss head after reassembly is to spin it dry for 10 minutes WITHOUT HEAT (use motor switch only).

Reassembly of Floss Band and Element

1. When reassembling, the floss band and element must be properly seated on the spinner head groove provided for the Quick Release Floss Cap to correctly and easily lock into place. The band is marked to show correct orientation for installation (see image below).
2. Reattach the (2) element lead wires to the (2) power studs, and secure with the terminal lock and ball knob.
3. Slide the Take-Apart Spinner Cap onto the retaining bolts.
4. Place the Quick Release Floss Cap over the spinner cap and make sure it is fully rotated counterclockwise into the locking position.
5. Check the rubber floats to make sure they are fully inserted in the float holders on the Quick Release Floss Cap.

Troubleshooting

instructions for removing and cleaning band and element (see Floss Band and Element section).
B. Low line voltage.| B. If the Auto Cooling Light is blinking during machine operation, it indicates there is low wall line voltage to the machine (less than 105 VAC). A primary reason for low production and poor equipment performance is low line voltage. Have a qualified electrician check the wall line voltage (where the machine is plugged in), and add new lines for all the various equipment plugged into the electric circuit if there is not enough current for the requirement listed on the equipment nameplate.

The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. If the use of an extension cord cannot be avoided then be sure it is no longer than 10 to 12 ft., and is at least 14 AWG wire.

C. Foreign objects in the spinner head.| C. Foreign objects in the head assembly can short out an element or cause an out-of-balance condition.
Excessive Smoke| A. Bypassing the cooling cycle.| A. Bypassing the cooling cycle will cause excessive smoke and melting sugar. This can cause carbon buildup. See Floss Band and Element section of this manual for cleaning the band and element.
B. Product mixture.| B. Check the product mixture being used. For best results, use nothing with a cornstarch base.
C. Excessive sugar buildup.| C. Check the band for excessive sugar buildup and remove if needed as described in the Floss Band and Element section of this manual.
Excessive Vibration| A. Packing material not removed.| A. If the equipment is new, check that all packing materials were removed from the machine.
B. Lock-N-Go Handles not in operating position.| B. Verify that the Lock-N-Go Handles have been rotated into the operating position.
C. Low on sugar.| C. Refill the floss head; this will normally eliminate excessive vibration. When adding sugar to the floss head, always fill it 90% full to obtain a balanced condition in the head and eliminate vibration. Do not add sugar with the motor running!
 |  |
---|---|---
Issue| Possible Cause| Solution
 | D. Foreign objects or sugar lumps.| D. Run the sugar completely out, then check for foreign objects or sugar lumps in the head assembly.
E. Stretched or uneven suspension springs.| E. If the suspension springs are stretched or uneven this can cause unwanted vibrations. Have Qualified Service Personnel replace if needed.
Lock-N-Go Handles are Hard to Rotate| A. Clamping Cam friction.| A. If handles are hard to move, Qualified Service Personnel may need to apply Petro Gel (Gold Medal Item No. 1110), or a food safe lubricant, to the top surface of the Clamping Cam to reduce friction where the cam contacts the bell housing.
Quick Release Floss Cap is Hard to Rotate| A. Hard to twist OFF (sugar build up)| A. If Quick Release Floss Cap is hard to twist off, clean any sugar build up before reinstalling.
B. Hard to twist ON (band/element position)| B. If cap is hard to twist on, check that the band and element are properly seated in spinner head groove provided (see Reassembly of Floss Band and Element).

MAINTENANCE INSTRUCTIONS

How to Check a Triac

1. Set the Multimeter for ohms or continuity.
2. Disconnect all machine leads from the Triac.
3. Connect the positive ohmmeter lead to MT2 and the negative lead to MT1. The ohmmeter should indicate no continuity (OL) through the Triac.
4. Using a separate jumper lead, connect the gate of the Triac to MT2. The ohmmeter should indicate continuity (less than 100 ohms).
5. Reconnect the Triac so MT1 is connected to the positive ohmmeter lead and the negative lead to MT2. The ohmmeter should indicate no continuity (OL) through the Triac.
6. Using a separate jumper lead, connect the gate of the Triac to MT2. The ohmmeter should indicate continuity (less than 100 ohms).

ORDERING SPARE PARTS

1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)

2. Use only approved replacement parts when servicing this unit.

3. When ordering, please include part number, part name, and quantity needed.

4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order.

5. Address all parts orders to:

   • Parts Department Gold Medal Products Co.
     10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online: Phone: 800-543-0862 /513-769-7676

   • Fax: 800-542-1496 /513-769-8500

   • E-mail: info@gmpopcorn.com

   • Web Page: gmpopcorn.com

Cabinet Exterior and Lock-N-Go Handle Assembly

Cabinet Exterior and Lock-N-Go Handle Assembly – Parts List

3052-00- 001

1

| SPINNER HEAD, TUBULAR 5IN HEAD (Complete

Assembly) See Spinner Head Assembly section for individual parts breakdown.

| ****

55139C

2

| BRUSH HOLDER ASSY (includes Brushes, Caps and Holders) See Brush Assembly Breakdown section for individual parts breakdown.| ****

42382W

3| BELL HOUSING, DUAL BRUSH| 42190
4| LABEL,FLOSS ADVERTISEMENT| 42159
5| BOWL, SEAL RETAINER| 56561
6| BELL HOUSING SEAL| 56571
7| THREADED BUMPER,1/4-20| 102017
8| NAME,INSTRUCTION OVERLAY| 102028
9| SWITCH, LIGHTED ROCKER GR| 42798
10| PILOT LIGHT, AMBER 125V| 55039
11| SWITCH, ROCKER DPDT| 48615
12| 10-24 X 1/2 PH TRUSS M/S| 42826
13| HEX NUT #10-24 ESLOK| 74691
14| RUBBER FOOT 3/4IN HIGH| 47155
15| HANDLE UNLOCK DECAL| 102253
16| LOCK N GO HANDLE, NEW CAB.| 56563
17| 5/16-18 X 1/2 PH TR M/S| 12183
18| WASHER SS .5 ID X 1.10 OD| 48428
19| CLAMPING SHAFT, LOCK N GO| 56565
20| CLAMPING CAM| 42460
21| 5/16 FLAT WASHER ZINC PLT| 74134
22| HEX NUT 5/16-18 ESLOK| 12001
23*| POWER SUPPLY CORD| 22038
24| STRAIN RELIEF SR-6P3-4| 76026
25| WARNING LABEL CORD| 68720
26| 8-32 X 3/8 PHIL PAN HEAD| 87515
27| 1/4-20 X 3/4 GRADE 5 BOLT (w/Lock Washer)| 74520
28| TINNERMAN NUT 1/4-20| 42125
29| 8-32 X 3/8 SLT. HWH M/S| 42044
30| #8-32 TINNERMAN FASTENER| 47299
31| INSPECTION BRUSH COVER| 42381
32| LABEL,CLEAN EVERY 500 LBS| 42002

5” Take Apart Spinner Head (Model No. 55139C)

5” Take Apart Spinner Head (Model No. 55139C) – Parts List

55139C
1| MOLDED RUBBER FLOAT| 56549
2| QUICK RELEASE FLOSS CAP (includes 2 Molded Rubber Floats| 102039
3| TAKE-APART SPINNER CAP| 43166C
4| BREEZE BAND ASSEMBLY (includes element)| 48784
5| FLOSSHEAD RETAINING BOLT| 56550
6| BLACK BALL KNOB| 102050
7| TERMINAL LOCK| 56551
8| FLOSS ELEMENT BRACKET| 55118
9| 8-32 LOCKNUT, REVERSIBLE| 48767
10| #8 INTERNAL TOOTH L/W 410SS| 12132
11| COUNTER WEIGHT| 55006
12| .188ID FLATWASHER| 77052
13| 8-32 X 5/16 PH PAN M/S| 89247

14

| SPINNER BOTTOM, TUBULAR (Complete bottom assembly includes Terminal Lock, Ball Knob, and

items listed below.)

| ****

42284T

15| UPPER SPINNER HEAD| 42437
16| 1/4-20 x 3IN SET SCREW| 102038
17| 1/4-20 SERRATED LOCK NUT| 46311
18| HEX NUT #10-32 BRASS| 42301
19| #10 INTERNAL TOOTH WASHER| 12573
20| SLIP RING STUD| 42127
21| SLIP RING MACHINED| 42126HD
22| LOWER SPINNER HEAD 1/2| 42281
23| SET SCREW 1/4-20 X 3/8

(2 required for the Lower Spinner Head)

| 74125
24| BOTTOM PHENOLIC WASHER| 20054

Bell Housing Interior – Brush Assembly

3052-00- 001
1| HEX NUT #10-24 ESLOK| 74691
2| .188ID FLATWASHER| 77052
3| MOTOR MTG PLATE| 42119
4| MOTOR, FLOSS MACHINE| 48649
5| 6-32 X 1/2 PH PAN HD M/S| 47516
6| 6-32 GRIP NUT ZINC PLATED| 47517
7| BRUSH HOLDER ASSEMBLY (includes Brushes, Caps and Holders)| 42382W
8| DUAL BRUSH HOLDER W/LEADS| 42436W
9| CARBON BRUSH| 55007
10| CAP, BRUSH HOLDER| 42138

Cabinet Interior – Parts Breakdown

Cabinet Interior – Parts List

3052-00- 001
1| MOTOR, FLOSS MACHINE| 48649
2| SWITCH, ROCKER DPDT| 48615
3| PILOT LIGHT, AMBER 125V| 55039
4| SWITCH, LIGHTED ROCKER GR| 42798
5| AUTO WATT CONTROLLER| 55447
6| 6-32 X 3/8 PHIL PAN M/S| 39000
7| WASHER #6 INTERNAL TOOTH| 76188
8| TRIAC, 35A 600V| 55155
9| HEAT SINK| 48673
10| 10-32 X 1/2 TRUSS HEAD| 12189
11| TERMINAL BLOCK, 2 POS| 55620
12| 8-32 X 3/4 PHIL PAN MS SS| 39007
13| HEX NUT #8-32 STAINLESS| 89129
14| ACORN NUT 1/4-20| 49068
15| SPRING, SUSPENSION MEDIUM| 42524
16| SCREW 1/4-20X3/8 PN HD PH| 42360
17| 10-24 TINNERMAM FASTENER| 42221

Floss Pan and Whirlgrip Stabilizer

3052-00- 001
1| FLOSS PAN, 0.080 ALUM| 42040
2| WHIRLGRIP STABILIZER (Includes Floss Stabilizer and Clips)| 3010
3| FLOSS STABILIZER (Web)| 43032
4| WHIRLGRIP CLIPS| 77470

Wiring Diagram

Model No. 3052-00-001

WARRANTY

• Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for “Perishable Parts” on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.

• THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
  NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.

• In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.

• The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.

• THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.

• NOTE: This equipment is manufactured and sold for commercial use only.

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com

Phone: 800-543-0862 /513-769-7676

Fax: 800-542-1496 /513-769-8500

© 2018 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.

References

• Concession Supplies & Equipment | Gold Medal Products Co.
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>