HONDA Civic LX 4dr Sedan Car Instruction Manual

HONDA Civic LX 4dr Sedan Car

Product Information

Specifications

• Model: i-MID
• USB Update Device: T/N 07AAZ-TR0A300
• Tool Number: 07AAZ-TR0A300
• Operation Number: 8415A2
• Flat Rate Time: 0.3 hours
• Failed Part: 78260-TR0-A11
• Defect Code: 03214
• Symptom Code: 03217

Product Usage Instructions

Step 1: Connect the USB update device

Locate the USB port in the centre console of your vehicle. Connect the USB update device (T/N 07AAZ-TR0A300) to the USB port.

Step 2: Turn on the ignition

Turn the ignition switch to the ON (II) position.

Step 3: Access the Vehicle Menu

Push the MENU button on the steering wheel to access the Vehicle Menu.

Step 4: Enter engineering diagnosis mode

Press and hold the MENU button, and then press the SOURCE button five times to enter the engineering diagnosis mode. Highlight “Version” and press the SOURCE button.

Step 5: Check the software version

Scroll down and check the software version displayed on the screen.

Step 6: Perform software update

Scroll down, highlight “Version Up”, and press the SOURCE button. The update process will begin.

Step 7: Wait for the update to complete

Do not remove the USB update device or turn the ignition switch to the LOCK (0) position during the update. The update should take about 15 to 20 minutes. If you are in a brightly lit area, the screen may dim.

Step 8: Reset and finalize the update

When the update is completed and the i-MID resets, the clock will begin flashing. The update process is now complete.

FAQ

• Q: Can I use the USB update device in other vehicles?
• A: No, the USB update device (T/N 07AAZ-TR0A300) should only be used in the vehicles listed in this bulletin. Using it in other vehicles may cause incorrect operation of their systems.
• Q: What should I do if I lose or don’t have the USB memory stick?
• A: If you lose or don’t have the USB memory stick, call the Special Tools hotline at 1-800-346-6327 for assistance.
• Q: How long does the software update take?
• A: The software update process should take about 15 to 20 minutes to complete.

USING INSTRUCTIONS

The i-MID Does Not Display Odometer, Trip, Fuel Range, and Economy Statuses
(Supersedes 13-017, i-MID Software Update, dated April 4, 2013, to revise the information marked by the black bar)

REVISION SUMMARY
The title was updated to be more symptom-based.
SYMPTOM
The odometer, trip computer, fuel range, and fuel economy statuses are not visible on the i-MID display.
POSSIBLE CAUSE
There is a problem with the i-MID unit which may prevent it from receiving B-CAN communication messages from other devices on the CAN bus line.
NOTE: Do not use this USB update device (T/N 07AAZ-TR0A300) in any other vehicle other than those listed in this bulletin because it will result in that vehicle’s system(s) operating incorrectly.
CORRECTIVE ACTION
Update the i-MID software.

TOOL INFORMATION

• USB Update Device: T/N 07AAZ-TR0A300 Each dealer was sent a USB update device.
• If the USB memory stick is lost or not available, call the Special Tools hotline at 1-800-346-6327.

WARRANTY CLAIM INFORMATION

The normal warranty applies.

• Operation Number: 8415A2
• Flat Rate Time: 0.3
• Failed Part: 78260-TR0-A11
• Defect Code: 03214
• Symptom Code: 03217
• Skill Level: Repair Technician

REPAIR PROCEDURE
NOTE

• Keep the ignition switch in the ON (II) position. Connect a jumper battery to the vehicle. (Do not use a battery charger.)
• To prevent i-MID damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update.

1. Connect the USB update device to the USB port located in the centre console.

2. Turn the ignition switch to the ON (II) position.

3. Push the MENU button on the steering wheel to access the Vehicle Menu.

4. Press and hold the MENU button, and press the SOURCE button five times to enter the engineering diagnosis mode. Highlight the Version, then press the SOURCE button.

5. Check the software version.

   • If the software version is MajorV105 or later (shown on the i-MID display as Major 105 or later), this service bulletin does not apply. Continue with normal troubleshooting.
   • If the software version is MajorV104 (shown on the i-MID display as Major 104), go to step 6.

6. Scroll down, highlight Version Up, and press the SOURCE button.

7. Highlight the SYSTEM, and press the SOURCE button.
   NOTE: If you are in a brightly lit area, the screen may dim. The update should take about 15 to 20 minutes. Do not interrupt the update during this time or the i-MID will be damaged.

8. The update begins, and then the following screens appear.
   NOTE: Do not remove the USB update device or turn the ignition switch to the LOCK (0) position.
   NOTE: The following screen appears when there is about 1 minute left .

9. When the update is completed and the i-MID resets, the clock will begin flashing.

10. Repeat steps 3–5 to check that the software is updated to MAJORV105. If the software is not updated, go to step 1 and repeat this procedure.

11. Press the MENU button to exit the diagnosis mode and reset the clock to the correct time. Remove the USB update device.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>