DYNOJET PC6-23007 Power Commander 6 Installation Guide

: June 4, 2024
: Dynojet

Table of Contents

DYNOJET PC6-23007 Power Commander 6
PARTS LIST
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
WIRE CONNECTIONS
INSTALLING THE POWER COMMANDER 6
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DYNOJET PC6-23007 Power Commander 6

DYNOJET-PC6-23007-Power-Commander-6-product

PARTS LIST

1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
2 POSI-TAPS

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

DYNOJET-PC6-23007-Power-Commander-6-fig-1

OPTIONAL ACCESSORY INPUTS

Map: (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
Shifter: (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed: If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is set up you can alter your map based on gear position and setup gear-dependent kill times when using a quick shifter.
Analog: This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
Launch: You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS

To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.

NOTE: If you tin the wires with solder it will make inserting them easier.

INSTALLING THE POWER COMMANDER 6

DYNOJET-PC6-23007-Power-Commander-6-fig-3

Remove the seat and the plastic panel on the left hand side of the bike.
Route the PC6 harness from the left side of the bike and go towards the throttle body.
Unplug the stock wiring harness from the fuel injector.
Plug the PC6 connectors in-line of the fuel injector and the stock wiring harness.
Locate the stock Throttle Position Sensor on the right side of the throttle body and unplug the wiring harness from the TPS.
Plug the PC6 harness in-line of the stock wiring harness and the TPS.
Using the supplied Positaps, attach the crank signal input wires of the PC6 to the stock Crank Position Sensor wires. This connection can be found near the bundle of wires towards the rear of the throttle body. The PC6 WHITE/BROWN wire should attach to the stock GREEN wire.
Unplug the stock wiring harness from the ignition coil.
Plug the PC6 harness in-line of the ignition coil and the stock wiring harness.
Attach the ground wire of the PC6 to the negative side of the battery.
Using the supplied Velcro, attach the PC6 module to the inside of the left radiator shroud. Clean both surfaces with the supplied alcohol swab before attaching the Velcro.
Reinstall the seat.