JENSEN VX7020A 6.2 Double DIN Multimedia Receiver Installation Guide
- June 16, 2024
- Jensen
Table of Contents
JENSEN VX7020A 6.2 Double DIN Multimedia Receiver Installation Guide
What’s in the Box
The following items are supplied with the VX7020A:
- VX7020A Head Unit
- Trim Rings
- Hardware
- Power / Speaker Output / Accessory Harness
- Remote Control
- External Microphone
- GPS Antenna
- Operation / Navigation Manual / Warranty Card
- Installation Guide
Optional Equipment
- Steering Wheel Control (SWC) – The VX7020A is SWC ready for vehicles equipped with the option. See wiring diagram for installation details. For SWC programming details, please see the operation manual.
- Rear Camera – The VX7020A is Rear Camera ready for vehicles equipped with the option. See wiring diagram for installation details.
Disconnect the Battery
- To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VX7020A is to be installed in a car equipped with an on- board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.
Replacing the Fuse
- When replacing the vehicles radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating could damage the unit and cause a fi re.
ISO-DIN Installation
The VX7020A is designed to fi t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation.
-
Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.
-
Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer screws may damage components inside the chassis. -
Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, plug the connector into the mating socket on the rear of the chassis. Turn the unit on to confirm operation (vehicle ignition switch must be “ON”). If the unit does not operate, re-check all wiring until the problem is corrected.
-
Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation fl
exibility. This unit will fi t into most import dashes with little or no
modifi cation to the dash board/cavity. Some US domestic vehicle dashes will
accept a Double-DIN chassis, but there is usually a small gap between the
radio and dash piece after installation is complete. In this case, use the
trim ring to conceal any gaps that may be present.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the unit is mounted within this limitation.
Wiring Diagram
CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit.
Follow the wiring instructions
carefully, or have the installation handled by an experienced technician.
The VX7020
A has a built-in SWC Interface compatible with most resistive type OE steering
wheel controls. In most installations, only two of the three wires will be
needed to interface the OE steering wheel controls to the VX7020 A.
SWC A – Primary SWC Wire
SWC B – Secondary SWC Wire try the SWC B and SWC Grou Initial wiring of
the SWC interface should include the SWC A and SWC Ground wire. If this
combination of wiring does not support your vehicle functions, then SWC Ground
– Chassis ground nd wire combination. Do not use only SWC A and SWC B. The SWC
Ground must be connected.
Some vehicles may not support all SWC functions. Professional Installation
is recommended.
www.asaelectronics.com
© 2015
Printed in China
Documents / Resources
|
JENSEN VX7020A 6.2 Double DIN Multimedia
Receiver
[pdf] Installation Guide
VX7020A 6.2 Double DIN Multimedia Receiver, VX7020A, 6.2 Double DIN Multimedia
Receiver, DIN Multimedia Receiver, Multimedia Receiver, Receiver
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>