J-TECH DIGITAL JTECH-4K60-UNT ProAV Many Many 4K 60Hz HDMI Extender with IR User Manual

J-TECH DIGITAL JTECH-4K60-UNT ProAV Many Many 4K 60Hz HDMI Extender with

IR

Product Information

Model: JTECH-4K60-UNT JTECH-4K60-UNR

Brand: ProAV

Product Type: Many to Many 4K@60Hz HDMI
Extender with IR

JTD-ID: 327/328

Product Website: https://manual-hub.com/

Specifications

• Extends 4KX2K@60HZ HDMI signals up to 120m over a single UTP 00Cat5e/6 cable
• Multicasting and broadcasting architecture, adding more displays without adding LAN bandwidth loading
• Support Point-to-Point, Point-to-Many, and Many-to-Many network configuration
• Wideband IR (20-60kHz) control to the source
• Can be cascaded for many layers by adding Ethernet switches

Product Usage Instructions

Installation

To set up the JTECH-4K60-UNT JTECH-4K60-UNR HDMI Extender, follow these steps:

1. Connect the transmitter unit (TX) to the HDMI source device using an HDMI cable.
2. Connect the receiver unit (RX) to the display device using an HDMI cable.
3. Connect a UTP Cat5e/6 cable between the TX and RX units.
4. Ensure both the TX and RX units are connected to a power source using the provided power adapters.
5. If cascading is desired, connect additional RX units to the UTP Cat5e/6 cables and power them on.

Configuration

The JTECH-4K60-UNT JTECH-4K60-UNR HDMI Extender supports various network configurations:

• Point-to-Point: Connect one TX unit to one RX unit for a direct connection between a source device and a display device.
• Point-to-Many: Connect one TX unit to multiple RX units using Ethernet switches to distribute the HDMI signal to multiple display devices.
• Many-to-Many: Connect multiple TX and RX units using Ethernet switches to create a network where any source device can be displayed on any display device.

IR Control

The JTECH-4K60-UNT JTECH-4K60-UNR HDMI Extender supports IR passback function, allowing you to control the media playback of the source device at the display location.

To use the IR control feature, ensure that the IR cables are connected between the TX and RX units. Point the IR remote control towards the RX unit to control the source device.

Ethernet Switch

If you wish to cascade multiple layers of JTECH-4K60-UNT  JTECH-4K60-UNR HDMI Extenders, you can add Ethernet switches to expand the network. Simply connect the TX and RX units to the Ethernet switches using UTP Cat5e/6 cables.

Important safety notice

Please read below safety instructions carefully before installation and operation:

• Please pay attention to all the warnings and hints on this device.
• Do not expose this unit to rain, moisture and liquid.
• Do not put any stuff into the device.
• Do not repair or open this device without professional people’s guidance.
• Make sure good ventilation openings to avoid product overheating damage.
• Shut off power and make sure environment is safe before installation.
• Do not plug-in/out the network cables and IR cables when it is in using to avoid cables damage.
• Use DC5V/3A only. Make sure the specification matches if using 3rd party DC adapters.

Introduction

HDbitT HDMI extender includes a transmitter unit(TX) and a receiver unit(RX). It applied advanced HDbitT technology, and the resolution supported is up to 4Kx2K@60Hz ultra HD. It supports one-to-one, one to many and many-to-many connections. the transmission distance is up to 120 meters. With the IR passback function, it is very easy to control media playback of the signal source device at the display location.

Features

1. Use Gigabit/100M IP switch for extension and distribution
2. Extends 4KX2K@60HZ HDMI signals up to 120m over a single UTP Cat5e/6 cable
3. Multicasting and broadcasting architecture, adding more displays without adding LAN bandwidth loading
4.  Support Point-to-Point, Point-to-Many and Many-to-Many network configuration
5. With wideband IR (20-60kHz) control to the source
6. Can be cascaded for many layers by adding ethernet switches

Package Contents

Installation Requirements

1. HDMI source device (computer graphics card, DVD, PS3, HD monitoring equipment etc).
2. HDMI display device like SDTV, HDTV, projector with HDMI port.
3. Network cables: UTP/STP Cat5e/6 network cables, which following the standard of IEEE-568B.
4. Transmission length: CAT5 80m/CATE 100m/CAT6 120m.

Panel Description

HDMI EXTENDER TX

HDMI EXTENDER RX

Installation Procedures

How to make a Cat5e/6 network cable Follow the standard of IEEE-568B:

1. Orange/white
2. Blue
3. Orange
4. Blue/white
5. Green/white
6. Green
7. Brown/white
8. Brown

Connections

1. One-to-one connection: up to 120 meters transmission distance over a single CAT (High-quality cable can reach 150 meters).
2. One-to-many Connection: by using network router/switch, one sender to several receivers, realize extender and splitter function.
3. Many to many

Disclaimer

The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted from the user manual. The pictures on the user manual are just for reference, and there may be some slight differences with the real products. We reserve the right to make changes without further notice to a product or system described herein to improve reliability, function, or design.

www.jtechdigital.com

Product pictures are for reference only.
Specifications described herein are subject to change without prior notification.
All trademarks are the sole property of their respective companies.
Copyright ©J-Techdigital, Inc. All rights reserved.

FAQ

What is the maximum transmission distance of the JTECH-4K60-UNT JTECH- 4K60-UNR HDMI Extender?

The JTECH-4K60-UNT JTECH-4K60-UNR HDMI Extender can transmit HDMI signals up to 120 meters over a single UTP Cat5e/6 cable.

Can I connect multiple display devices to a single TX unit?

Yes, you can connect multiple display devices to a single TX unit by using Ethernet switches in a Point-to-Many configuration.

Can I control the source device from the display location?

Yes, the JTECH-4K60-UNT JTECH-4K60-UNR HDMI Extender supports IR passback function, allowing you to control the source device using the IR remote control at the display location.

Q: TV display “Waiting for connection” on the right corner?

A: Please check if the power supply of TX (Sender) and switcher (if used) is connected, and make sure all the cables are connected well.

Q: TV display “Please check the TX input signal”?

A: Please check if there is an HDMI signal input of TX.
Try to connect the signal source directly to the display device to see if there is a single output from the source device or change the signal source, HDMI wire, and try again.

Q: When playing 4Kx2K source, the screen is black without any content?

A: Please check and make sure both the display and HDMI cable comply with HDMI 2.0.
(Input cable length supported ≤5m(AWG24))

Q: Display is not fluent, not stable?

A: Please check the cable length between the TX to switch, the switch to the RX and the connection between each level is within the required range.
Press the” reset” button on the TX/RX front panel, reset and reconnect.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>