J-TECH DIGITAL JTECH-WE300 200M Wireless HDMI Extender User Manual

J-TECH DIGITAL JTECH-WE300 200M Wireless HDMI Extender

Product Information

Specifications

• Transmitter Interface : IR output; HDMI in (Type A female); 2 Antenna port (RP-SMA male); DC input; USB2.0(Type A)
• Supply Voltage Range : 5V DC
• Power Consumption: N/A
• Weight : N/A
• Size : N/A

Packing List

1. Transmitter : 1 piece
2. Receiver : 1 piece
3. 5V/2A Power Adapter (Pair Locked Adapter): 2 pieces
4. Antenna : 4 pieces
5. R Emitter : 1 piece
6. IR Receiver: 1 piece
7. Mount: 4 pieces

Contact Information

• Website: www.jtechdigital.com
• Toll Free: 1-888-610-2818
• Email: support@jtechdigital.com

Product Usage Instructions

1. Step 1: Connecting the Transmitter
2. Connect the IR output cable to the IR output port on the transmitter.
3. Connect the HDMI cable to the HDMI input port on the transmitter.
4. Connect the antennas to the antenna ports on the transmitter.
5. Connect the power adapter to the DC input port on the transmitter.
6. (Optional) Connect a USB device to the USB2.0 port on the transmitter.
7. Step 2: Connecting the Receiver
8. **** Connect the HDMI cable to the HDMI input port on your display or device.
9. Connect the antennas to the antenna ports on the receiver
10. Connect the power adapter to the DC input port on the receiver.
11. Step 3: Setting Up the IR Remote Control Extension
12. **** Place the R Emitter near the IR sensor of the device you want to control.
13. Place the IR Receiver near your remote control.
14. Step 4: Mounting
15. Use the provided mounts to secure the transmitter, receiver, and other components in your desired locations.
16. Step 5: Powering On
17. Ensure that all connections are secure.
18. Plug in the power adapters for both the transmitter and receiver into a power outlet. 3. The system will power on automatically.

Frequently Asked Questions (FAQ)

1. Q: What is the purpose of the IR Remote Control Extension?
   A: The IR Remote Control Extension allows you to control devices that are not in direct line of sight with the remote control.

2. Q: Can I connect multiple transmitters and receivers together?
   A: No, this system is designed for one-to-one connectivity between a single transmitter and a single receiver.

3. Q: Can I use this product with any HDMI device?
   A: Yes, as long as the HDMI device supports the require specifications.

• Website : www.jtechdigital.com
• Toll Free : 1-888-610-2818
• Email : support@jtechdigital.com

USER MANUAL

• J-Tech Digital® Wireless Extender WE300 1080P 200M
• Model : JTECH-WE300

PACKING LIST

1. Transmitter : 1pcs
2. Antenna: 4pcs
3. Receiver : 1pcs
4. R Emitter: 1pcs
5. 5V/2A Power Adapter(Pair Locked Adapter) : 2pcs
6. IR Receiver: 1pcs
7. Mount ： 4pcs

PARAMETERS

INTRODUCTION

• The wireless high-definition video transmission system, using today’s highest level of wireless communication technology, supports HDMI 1080p@60Hz HD signals. This set includes one Transmitter and one Receiver, which both utilize the 5.1-5.8GHz frequency band. Different preset wireless channels can be selected based on different countries’ requirements, or to connect several Transmitters and Receivers within the same location.
• This extender supports one-way IR, making it easy for customers to control an HDMI source from the Receiver/display side. This extender has a transmission rate of up to 8Mbps, which ensures that HD video and audio can be transmitted smoothly & synchronously. It also supports point-to-point signal transmission and allows multiple units to be used in the same area. Customers can distinguish multiple units through different indicator lights. Its effective transmission range is 200 meters (660 feet) in direct LOS (line-of-sight). With 5V/2A adapters and 5dBi antennas, all the ports pass the ±4KV ESD test (HBM, Human contact discharge model), and the reliability of the device can be ensured.

PRODUCT INTRODUCTION

TRANSMITTER

1. HDMI Input
2. Pairing Button
3. IR Output
4. Reset Button
5. USB port
6. 5V DC

RECEIVER

1. HDMI Output
2. Pairing Button
3. IR Input
4. Reset Button
5. USB port
6. 5V DC

PRODUCT INSTALLATION AND USE

Equipment installation and use

1. Place your Transmitter near your source device and your Receiver near your display, then attach the high-gain antennas on both devices and connect the power adapters to each component.
2. Connect an HDMI source to the Transmitter using an HDMI cable, and connect the display to the Receiver with an HDMI cable as well.

Paring introduction

This product supports a 1 to 1 signal transmission and arrives already paired by default. When connecting several sets of wireless extenders or after a power outage, pairing the
Transmitter and Receiver may be necessary. The pairing steps are below:

1.  Power the Transmitter and Receiver, then connect your signal source and display respectively.
2. After powering them on, press the pair button on the receiver and transmitter at the same time for about 6 to 10 seconds until the light stays on, which means that they have paired successfully. The video signal from the source should now appear on your display.

COMMON TROUBLESHOOTING

1. Poor video quality
2. Check and ensure that the HDMI input and output cables are connected properly
3. Adjust the angles of the antennae on both the Transmitter and Receiver, adjust until a stable video signal is attained.
4. Make sure that the Transmitter and Receiver are within  the effective distance and within direct line-of-sight
5. The display keeps showing the status message: “Searching TX xxxx….”
6. Check that the Transmitter is receiving power, then check if the HDMI cable is connected properly
7. Check if the video source output format is compatible with this product (resolutions with a 16:9 aspect ratio are recommended for optimal compatibility)
8. The Transmitter and Receiver may not be paired and may have to be repaired. Please see the Pairing instructions found under Product Installation and Use section.
9. The video is not smooth, or is dropping intermittently
10. Check that the Transmitter’s and Receiver’s HDMI cables are properly connected
11. Adjust the angles of the antennae on both the Transmitter and Receiver, adjust until a stable video signal is attained. Please check the packet loss rate in the Network of the
12. OSD menu, and determine whether the wireless signal is in the normal range, also please confirm the protocol is set to UDP
13. Reposition the Transmitter and Receiver, or move close to each other, and eliminate any obstacles in between if possible.
14. No output on display
15. Check to make sure both the Transmitter and Receiver are receiving power and ensure that their respective HDMI cables are connected properly.
16. Test the extender with new or different HDMI cables on both the Transmitter and Receiver. If there is still no display after changing HDMI cables, contact our Tech Support team

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation

Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

www.jtechdigital.com

• J-Tech Digital®12803 Park One DriveSugarland, TX 77478
• Product pictures are for reference only.
• Specifications, pictures & software described herein are subject to change without prior notification.
• Only use the provided power supply when operating this unit. J-Tech Digital® is not responsible for any damage due to customer neglect. All trademarks are the sole property of  their respective companies.
• Copyright ©J-Tech Digital, Inc. All rights reserved.

References

• J-Tech Digital ® Official Site | Professional AV Solution Provider
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>