JVC TS-C421SPG Speaker Unit Instruction Manual

: June 16, 2024
: JVC

Table of Contents

TS-C421SPG Speaker Unit
SAFETY PRECAUTIONS
Accessories
Names of parts
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TS-C421SPG Speaker Unit
Instruction Manual

TS-C421SPG Speaker Unit

SPEAKER UNIT
TS-C421SPG
TS-C421SPGU

SPEAKER UNIT FOR A JVC PLASMA DISPLAY MONITOR

SAFETY PRECAUTIONS

Regarding the “safety precaution” symbols
Various symbols are indicated on the product and in this Installation Manual.
These symbols are provided in order to prevent physical injury and material damage. Be sure you understand the meaning of the symbols before reading this manual.

Explanation of symbols

This symbol (including a warning) indicates that CAUTION should be exercised.
General caution
Prohibited actions are indicated by the following symbols.
Prohibited Disassembling prohibited
Actions that should be performed (compulsory and instructed actions) are indicated by the following symbol.
General instruction

WARNING Failure to observe what is mentioned under this symbol could lead to physical injury and material damage. Extreme caution should be exercised.

Do not modify (disassemble) the front speakers.
This could result in fire or electric shock.

CAUTION Failure to observe what is mentioned under this symbol could lead to physical injury and material damage. Extreme caution should be exercised.
• Connect the power cord plug to a wall outlet only after all necessary equipment has been connected.
Making connections while the power cord plug is connected to the wall outlet could result in electric shock.

Accessories

Check to be sure you have all of the supplied accessories. The number in the parentheses is the quantity of the pieces supplied. If anything is missing, contact your dealer immediately.

Names of parts

Attaching the front speakers to displays other than the GD-V42XX series

Using the speaker brackets, you can attach the front speakers to the side of the display.

For attaching the front speakers to the GD-V42XX series display, see page 4.
In this section, the GM-P420 series displays are shown in the illustrations. The mounting screw positions of the other displays are almost the same as those of the GM-P420 series, therefore you can attach the front speakers as in the procedure below.
Do not loosen the screws other than the mounting screws.
Use only the screws already attached to the display.

Loosen the mounting screws on the back of the display.
Loosen the mounting screws with Philips screwdriver, leaving a length of about 3 mm.
Attach the front speaker to the back of the display.
Hook the speaker bracket onto three mounting screws through the screw holes (A), and slide it down.
Tighten the mounting screws firmly with Philips screwdriver.

When moving the display, do not hold the speakers.
The speakers are not of anti-magnetic type.
Do not place anything susceptible to magnetism, such as a video tape, nearby when setting the speakers.

Connecting the speaker cord
Attach to the speakers
When you connect the supplied speaker cord to the terminal clamp of the speakers, fold the end of each speaker cord to avoid short-circuit.

Connect the cord with black stripes to the (black) terminal and the other cord to the (red) terminal.
Be careful that connection of the speaker cords to incorrect polarity terminals ( and ) degrades stereo feeling and sound qualities.

Attach to the display

Connect the cord with black stripes to the (black) terminal and the other cord to the (red) terminal.
Be careful that connection of the speaker cords to incorrect polarity terminals ( and ) degrades stereo feeling and sound qualities.

Bundling the speaker cords
You can bundle the speaker cords neatly with the supplied cord clamp, as illustrated.

Stick the cord clamp after removing its protective seal. Give an amount of time before bundling the speaker cords, or the cord clamp may be detached.
If you are sticking the cord clamp to the back of the display, be careful not to block the ventilation hole.

Attaching the front speakers to the GD-V42XX series display
Using the speaker brackets, you can attach the front speakers to the side of the display.

Do not loosen the screws other than the protective screws.
Use only the supplied mounting screws for attaching the front speaker.

Remove the protective screws on the back of the display with Philips screwdriver.
Before removing them, make sure which screws to be removed by placing the front speaker.
Place the front speaker on the back of the display so that the screw holes (B) of the speaker bracket are put on those of the display.
Tighten the three supplied mounting screws firmly with Philips screwdriver.
Use the rest of three supplied mounting screws on the other side. • When moving the display, do not hold the speakers.
• The speakers are not of anti-magnetic type.
Do not place anything susceptible to magnetism, such as a video tape, nearby when setting the speakers.

Connecting the speaker cord
Attach to the speakers
When you connect the supplied speaker cord to the terminal clamp of the speakers, fold the end of each speaker cord to avoid short-circuit.

Connect the cord with black stripes to the (black) terminal and the other cord to the (red) terminal.
Be careful that connection of the speaker cords to incorrect polarity terminals ( and ) degrades stereo feeling and sound qualities.

Attach to the display

Connect the cord with black stripes to the (black) terminal and the other cord to the (red) terminal.
Be careful that connection of the speaker cords to incorrect polarity terminals ( and ) degrades stereo feeling and sound qualities.

Bundling the speaker cords
You can bundle the speaker cords neatly with the supplied cord clamp, as illustrated.

Stick the cord clamp after removing its protective seal. Give an amount of time before bundling the speaker cords, or the cord clamp may be detached.
If you are sticking the cord clamp to the back of the display, be careful not to block the ventilation hole.