JVC LT-24HA48E 24 Inch Smart LED TV Instruction Manual

JVC LT-24HA48E 24 Inch Smart LED TV

• Model Numbers: LT-24HA48E, LT-29HA48E, LT-39HG48E
• Frame : Extra-slim frame with a superblack screen’s rim (3mm approx.)
• European Conformance
• In compliance with European directives and standards regarding electromagnetic compatibility and electrical safety
• Manufacturer’s European Representative: ORION ELECTRIC (POLAND) SP.ZO.O. OSTASZEWO 57 87-148 LYSOMICE POLAND

Product Usage Instructions

Important Safety Information

• To prevent fire, never place any type of candle or open flame on the top or near the TV set.
• Loud music can damage your hearing irreversibly, therefore do not set the volume to a high level when listening through headphones, particularly for extended listening periods.
• Use TV benches specifically constructed for this purpose.
• Maintain a distance between eyes and the screen that is about 3 ~ 4 times as long as the height of the screen.
• Avoid leaving the TV on for long periods of time while displaying a fixed (non-moving) pattern, as it can cause permanent ghost images on the LCD screen. This type of damage is not covered by the warranty.  Follow the cleaning instructions provided to clean the LCD TV.

How to Attach the Stand

1. Place the TV on its front onto a table.
2. Align the stand’s base-plate (supplied) as seen in the manual.
3. It will fit in only one direction. Make sure the locating pegs project through the locating holes.

Carefully hold the base plate in position and secure it with screws (4x16mm) LT-24HA48Ex3, LT-29HA48E/LT-39HG48Ex4 (included).

Dismantling the Base for Wall Mounting

1. To wall mount the TV, the base must be dismantled. Follow these steps
2. Remove screws (J) from the back of the TV.
3. Take off the base entirely.

Fit a VESA wall mounting kit (LT-24HA48E/LT-29HA48E: 100x100mm, LT-39HG48E: 200x100mm).

Cleaning Instructions for your LCD TV

• Before cleaning, switch off the TV and disconnect the plug from the mains power supply
• For complete disconnection from the mains power supply, remove the supplied power cable from the socket.

Frequently Asked Questions (FAQ):

• Q: What should I do if a fixed pattern remains on the LCD screen for a long time?
  A: If a fixed pattern remains on the LCD screen for long periods of time, it can cause permanent ghost images. This type of damage is not covered by the warranty. Avoid leaving the TV on for long periods of time while displaying fixed patterns.

• Q: How should I clean my LCD TV?
  A: Follow these steps to clean your LCD TV: – Switch off the TV and disconnect the plug from the mains power supply. – Use a soft, lint-free cloth to gently wipe the screen. – If necessary, dampen the cloth with water or a mild cleaning solution specifically designed for LCD screens. – Do not spray liquid directly onto the screen. – Avoid using abrasive cleaners or rough materials that may scratch the screen. – Dry the screen completely before reconnecting the power.

LED TV

• LT-24HA48E
• LT-29HA48E
• LT-39HG48E

Operating Instructions

Features

• 16:9 LCD screen
• LED-Backlight-Technology
• DVB-T-HDTV-Tuner
• Electronic Progr. Guide (EPG) for DVB USB-Media player
• Auto Power Off
• PVR (Personal Video Recorder) Time Shift
• New Thin-frame design*

Battery notice (valid in EU only)
Look after our environment – contact your local authorities for advice on how to safely dispose of exhausted batteries. The crossed out wheelie bin symbol indicates that used batteries should not be disposed of with your normal household waste! A separate collection system for used batteries is in place to allow the correct treatment and recycling in accordance with current legislation. Please contact your local authority for details on collection and recycling schemes in your area.

Information for the DVB-T function

• Any function relative to the digital television (with the DVB logo) is available only within the country or area where such signals are transmitted. Verify with the salesman if it is possible to receive a DVB-T signal in the zone where you live.
• Remove the CAM for DVB-T reception, if it has been inserted.
• A DVB-T antenna must be connected for DVB-T reception.
• Even if the television conforms to the DVB-T specifications, the compatibility to future digital DVB-T transmissions is not guaranteed.
• Some digital television functions may not be available in some countries.
• The DVB-T system present in this device is FTA (Free to air).

Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing – and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range.

Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
European representative of the manufacturer is:

• ORION ELECTRIC (POLAND) SP.ZO.O.

• OSTASZEWO 57 87-148 LYSOMICE

• POLAND

• The extra-slim frame allows more than a full view to the TV’s screen. Even the super black screen’s rim (3mm approx.) is now visible.

Important safety information

This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use.

• Although this appliance has been carefully manufactured and rigorously checked prior to leaving the factory, as with all electrical appliances it is possible for problems to develop. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you should disconnect the plug from the mains power socket immediately.

• Ensure that the unit is sufficiently ventilated! Never place next to or underneath curtains!

• This set should be only be connected to an AC 220~240V / 50Hz mains power supply – do not attempt to connect it to any other type of supply.

• The socket-outlet must be installed near the equipment and easily accessible.

• Any repairs must be carried out by qualified service personnel only.

• Do not open this unit. A non-expert attempting to repair the unit could be dangerous and potentially cause a fire hazard.

• Keep away from rodents. Rodents (and also cockatiels) enjoy biting into electric flexes.

• The animal can cause a short cut (fire hazard!) and receive a fatal electric shock.

• Always hold plug when pulling out plug from power mains supply system. Do not pull on flex. The flex can become overloaded and cause a short cut.

• Never wet clean. Only use a damp cloth, the same as when cleaning furniture.

• Do not submerge in or under water!

• Set up unit so that no one is able to trip over the flex.

• This unit is recommended to be installed on shock-free benches in order to avoid any danger from falling. Take note that toddlers can pull the unit down from the table or cupboard by means of its flex. Children can hurt themselves when doing this.

• Do not use the unit near heat sources. The casing and flex could be damaged by the impact of heat.

• Watch out for kiddies copying what adults do! Do not stick any objects through the vents!

• The vents must remain open! No newspapers or covers should be put on the unit!

• The remote control is not a toy! Toddlers could swallow the batteries. If a battery has been swallowed, please seek out a doctor immediately.

• The screen is made of glass and can break if damage is done to it. Be careful when collecting sharp-edged glass splitters.

• You could be hurt or the unit could be damaged.

• If the unit is mounted on the wall, contact the shop where you purchased the unit for advice, and leave the installation work to experts. Incomplete installation work can cause you injuries.

• Taking fall-prevention measures

  • If these measures are not taken, the unit can fall and you could be injured.

  • Contact the shop where you purchased the unit to obtain full details of the measures.
    When a TV stand is used,

  • Ensure the unit is fully on the stand and placed in the centre.

  • Do not leave the stand doors open.

  • You could be hurt as a result of the unit falling or breaking, or your fingers being caught or jammed. Take extra precautions if you have children.

• Avoid placing the unit on any surfaces that may be subject to vibrations or shocks.

• To protect the unit during a thunder storm unplug the AC power cord and disconnect the antenna. Caution: Do not touch the antenna connector.

• When you leave your home for a long period of time, unplug the AC power cord for safety reasons.

• The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to prevent overheating. The ventilation holes are not to be blocked. Do not set up near radiators. Do not place in direct sunshine. When placing on a shelf leave 10 cm free space around the whole unit.

• Make some space around TV (Correct shelf assembly).

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

• Liquids spilled into the unit can cause serious damage. Switch the set OFF and disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again.

Please pay attention to the following instructions in order to avoid receiving a life-threatening electric shock

• Protect against moisture. Never use in the bath or sauna.
• Never use near a bath, shower or swimming pool.
• Never use the unit if it has got wet. This can also mean condensation moisture, which occurs in the winter when the cold unit is brought into a heated flat. Wait before operating the unit especially after it has been transported in the winter, until the cold unit has adjusted to the room temperature.
• Do not place any heavy objects on the flex. Electrical isolation could be damaged.
• Never wrap insulating tape around damaged flexes or on damaged plugs. These should be repaired or replaced by qualified service personnel.
• Never use this unit if the cabinet is defective. Do not make provisional repairs if the cabinet is damaged – this  should be replaced by a new cabinet if necessary.
• Unplug the unit from the mains power supply prior to the cleaning of the unit.
• Never try to repair a damaged AC power cord with isolation-tape – this should be repaired by a specialist or replaced. Do not let your pet loose near the cable. Animals biting into the cable could receive a fatal electric shock, and could cause a hazard to others. https://manual-hub.com/

How to attach the stand

NOTE

• Unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on.
• Do not support the TV by the screen as sharp objects and too much pressure may cause damage.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.

1. Place the TV on its front onto a table.

2. Align the stand’s base-plate (supplied) as seen here.
   It will fit in only one direction. Make sure the locating pegs project through the locating holes.

3. Carefully hold the base plate in position and secure it with screws (4x16mm) LT-24HA48Ex3, LT-29HA48E/LT-39HG48Ex4 (included).

NOTE
To detach the base plate, perform these steps in reverse order.

Dismantling the base
For wall mounting, the base must be dismantled. To do this, remove screws (J, see page 10) from the back. Take off the base entirely. Fit a VESA (LT-24HA48E /LT-29HA48E: 100x100mm, LT-39HG48E: 200x100mm) wall mounting kit.
Notes when mounting the TV on a wall
Before wall-mounting, please check carefully the location of the TV’s mounting-holes. (see, “Dimension” on inside back cover)

WARNING To prevent fire, never place any type of candle or open flame on the top or near the TV set.

Headphone Warning
Loud music can damage your hearing irreversibly, therefore do not set the volume to a high level when listening through headphones, particularly for extended listening periods.
Moving the unit or carrying by hand

When the unit is moved a long way, unplug the power cord and disconnect the antenna, connecting cables and any fall-prevention apparatus.
Moving without doing so could result in damage to the power cord, a fire, electric shocks or injuries from dropping the unit.

Ensure that unpacking and transfer of the unit is carried out by two or more people and that the unit stays upright when doing this.
When the TV stand has casters, remove caster cups from the stand and push it while supporting the unit.

• Ensure that you support the unit when the stand is pushed, as this can cause the unit to fall and you could be injured.
• The appliance could leave indentations in wooden tables with extremely soft wooden surfaces due to  its heavy weight.
• Furniture polish could corrode and dissolve rubber feet. Black imprints could be visible on the table. You should therefore only use TV benches, which have been constructed for this specific purpose.

Secure the casters when the unit is installed on a TV stand with casters.
The stand can move and you could be hurt if the casters are not secured.
Remove casters when the stand is placed on a soft surface such as a mat and carpet.

The distance between eyes and the screen should be about 3 ~ 4 times as long as height of the screen.
Viewing from too close a distance can cause strain for your eyes.

When installing the Monitor on a table, be careful not to place the edge of its stand.
This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Possible Adverse Effects on LCD Screen : If a fixed (non-moving) pattern remains on the LCD screen for long periods of time, the image can become permanently engrained in the LCD TV panel and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for long periods of time while it is displaying the following formats or images

• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.
• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on a normal (4:3) display (Black bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen (16:9) display (Black bars on left and right sides of screen).

Attention!
Cleaning instructions for your LCD TV.

Safety note

• Before you start to clean, switch the set’s power off completely and disconnect the plug from the mains power supply.
• Be careful not to scratch the plastic coated front panel – it is highly vulnerable to accidental scratching (e.g. by fingernails or other sharp items). (While cleaning, do not wear jewelry) that could cause surface scratch-ing (such as rings, wrist-watch, etc.). Use a lint-free cloth and pure water to clean with, but make sure the cloth is thoroughly wrung out so that it is just damp and not soaking wet – also make sure that the cloth is free from any dirt that could cause scratching to the surface.
• Wipe the set clean using minimal pressure.
• Do not use standard window cleaning fluid. Its alcohol / ammonia will dissolve the front window’s coating. Never use solvent or thinner. Never use special cleaners which are designed for cleaning PC Monitors or CRT TVs.
• Finally carefully rub dry with a clean dry lint-free cloth.
• Do not use paper towels or tissues to clean the set – paper can disintegrate when wet or may leave a trail of dust behind. Some paper can also be abrasive and scratch your screen.

Saving electricity
The max. energy consumption during operation is reached only with maximal brightness of the display light. Maximal brightness is only necessary in a daylight environment in order to get a luminous and full of contrast picture. With less light in the environment, e.g. in the evening, the picture already can be too bright and might dazzle. The brightness of the display light can be reduced to the desired value in the menu Backlight (see p. 18). If the Back Light is set to a smaller value you can save up to 30 % of energy.

Note
The biggest energy saving effect is reached with minimal setting of Back Light.

Location of controls

Description of Indicators and Controls

1. Loudspeakers
2. Power indicator : The power indicator lights up red in standby mode, and green in power – ON mode.
3. Remote sensor
4 . TV/AV/ENTER button : Select input mode. In Menu : Using as ENTER button.
5. (Channel) / /▲/▼ buttons : Press to change to a higher numbered channel set into memory. Press to change to a lower numbered channel set into memory. In Menu: Setting.
6. (Volume) +/–/◀/▶/MENU buttons : Volume / In Menu :To display the menu screen. Press hold (Volume) +/– the same time about 1 second the menu will be appear.
7. (Power)-button : Preparation : Connect power-cable to AC220~240V/50Hz.
Press power-button to enter standby mode or turn on the power.
If you want to cut the mains power-supply, please power-off with your remote- unit first. Wait for the red light, before you cut the line. Failure to do so, might hinder the TV to save (memorize) recent settings.

For complete disconnection from the mains power supply, remove the supplied power cable from the socket.

Remote Control

Install the batteries
Use batteries type UM-4 (AAA-Size).
Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries – this could cause an explosion.

Note

• Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote control – therefore remove exhausted batteries immediately.
• Batteries should not be exposed to excessive heat such as sunshine, fire or the like.

1. Open the battery compartment.
2. Install the batteries as shown below, ensuring the correct polarity.
3. Close the battery compartment.

Distance of Remote Control Operation

The remote control handset will not work properly in the following cases

• If bright sunlight directly beams onto the unit front.
• If an obstacle is placed between the unit and the handset.
• If the batteries have not been installed according to their polarities.
• If the batteries are weak.

Antenna connection

Note : Before you connect other appliances

• To avoid potentially damaging your set, make sure all items are switched off and disconnected from the mains power when you make the connections.
• Arrange the desired connection.
• When you have finished making the connections, reconnect the mains power to the unit and switch it back on.

Connect your antenna as shown below (C). Connections to other equipment is explained further on P.26-27. If you have problems with reception, consult a specialist of antenna.

• (A) AUDIO (L/R) IN : Input for Audio input for component/AV (Sharing). See P.26-27.

• (B) DIGITAL AUDIO COAXIAL output : digital audio output. See P.26.

• (C) ANT.: Connect an antenna.
  The built-in tuner receives all DVB-T channels.

• (D) HEADPHONE jack : Plug headphones with a mini plug (3.5 mm) into this jack.

• USB input : See P.22-25. Use of this port by other than Service Personnel may void this products warranty.

• HDMI (LT-29HA48E/LT-39HG48E : HDMI1/2/3) input: See P.26.

• Y(VIDEO)/Pb/Pr input : Input for analogue Component-Signal. See P.26-27.
  Note : AV-CVBS input is sharing with component input.

• (H) C.I. slot : for CA- module (CAM) (if PayTV-provider supports this).
  Note : To prevent malfunctions and damages, be sure to turn off the TV before inserting or removing the CAM card.

• (I) Bracket holes : Fix a wall mounting bracket (not supplied) here.

• (J) To hang the television on a wall, remove these screws and then remove the stand.
  Before performing work spread cushioning over an area to lay the TV on.

Auto setup

At the first time you operate after the purchase, “Initial Setup” menu will appear.
You can repeat this process via the menu system (see page 19).

Preparation
Turn on TV-unit (see P.7) and connect antenna.

1. Initial Setup menu will appear.
   Press ▲ or ▼ to select desired language. Then press ▶ or ENTER.

2. Press ▲ or ▼ to select your country. Then press ▶ or ENTER.

3. Press ▲ or ▼ to select “Home Mode”, then press ▶ or ENTER.

4. If you cancel Auto Sleep (see page 19), press or ▼ to select Off, then press ▶ or ENTER. 

5. Connect your DVB-T antenna now.
   Press ▲ or ▼ to select “Scan”. Then press ▶ or ENTER.
   The tuning’s progress will be displayed in percent for confirmation. Note
   Please be patient – the Auto Tuning process can take several minutes to complete.

6. When the display reads 100%, press ENTER to exit the menu.
   Note
   To cancel the auto tuning, press RETURN, then press ◀ to select “YES” during the process, or press RETURN in the tuning progress.

THE AUTOMATIC TUNING PROCESS WILL ONLY START BY ITSELF THE FIRST TIME YOU SWITCH THE SET ON. HOWEVER YOU CAN RESTART THIS PROCESS VIA THE MENU SYSTEM (see page 19).
If you could not set up a correct language in this auto setup process, you will be able to make your preferred language selection as illustrated in page 12 (On-screen Language Selection).

Selecting the input source
Press INPUT SELECT to view a signal from another device connected to your TV, such as a VCR or DVD player.You can select each input source depending on which input jacks you used to connect your devices.
To select the video input source, press ▲/▼, then press ENTER.

On-screen Language Selection

1. Press MENU. Then press ◀ or ▶ to select “Setup”, then press ▼ or ENTER.
2. Press ▲ or ▼ to select “OSD Language”, then press ◀ or ▶ to select the desired language.
3. Press RETURN to exit the menu.

Station search
Warning! All previously saved DVB-T channels are deleted in Step 3. A new channel search then starts automatically.
Preparation
Make sure your antenna is connected to the antenna input (see P.10). Then press MENU.

1. Press ◀ or ▶ to select “TV”, then press ▼ or ENTER.

2. Press ▲ or ▼ select “Channels”, then press ▶ or ENTER.

3. Press ▲ or ▼ select “Channel Scan”, then press ▶ or ENTER.
   Press ◀ or ▶ to select desired country, then press ENTER.

4. The Channel Scan will search for available TV-channels and store the channels in the correct order.

5. When TV programme have been stored 100%, return to normal TV screen automatically.

Manual Channel Scan

• Preparation
  Select “Analogue Manual Scan” or “Digital Manual Scan” in Step 3 of Station search.

• Analogue Manual Scan
  Press ▲ or ▼ to select “Scan Up” or “Scan Down” to start searching. Then press ▶ or ENTER.

• Digital Manual Scan
  Select RF Channel that you want to setup, then press ENTER to start searching.
  You can verify the signal strength and quality of the selected service here. If necessary, adjust the direction of the DVB-T antenna to obtain the maximum signal strength.

Channel Setup

The Automatic station presetting stores the stations in a specific order. However, this order n be changed if you wish.

1. Press MENU. Press ◀ or ▶ to select “TV”, then press ▼ or ENTER.
2. Press ▲ or ▼ to select “Channels”, then press ▶ or ENTER.
3. Select desired option, then press ▶ or ENTER.

Description about the each setting option
Channel Skip : Press ▲ or ▼ to select the channel that you want to skip, then press ENTER. The mark will appear.
Channel Sort: Press ▲ or ▼ to select the channel that you want to move, then press ENTER. The mark will appear.
Press ▲ or ▼ to select the position that you want to move the channel to, then press ENTER.
Channel Edit : Press ▲ or ▼ to select the channel that you want to edit, then press ENTER. Following options are displayed.

• Channel Number : Press 0-9 buttons to enter the desired memory position number, then press ENTER.
• Channel Name : Press ENTER to enter edit mode, then press ▲/▼ to select desired letter, or ◀ to erase the letter, then press ENTER repeatly. – Frequency (only for Analogue TV): You can also directly enter the frequency value with Number buttons (0-9), then press ENTER.
• Color System (only for Analogue TV) : Color System has already been preset to Auto. Do not change anything here. Any changes can cause picture or sound disruption.
• Sound system (only for Analogue TV): Correct sound system is already installed. Any changes can cause sound disruption.

Analogue Channel Fine Tune (only for Analogue TV)
Already correctly and optimally installed. Do not change anything here. Any changes can cause picture or sound disruption. The video can also be affected.
Clean Channel List : Press ◀ to select “OK” and ENTER to delete all Channel.

Auto Synchronization
This feature can display the time based on the DVB signal information.
If you wish to set the time manually, select “Off” as follows and then perform the “Date” and “Time” options.

1. Press MENU. Press ◀ or ▶ to select “Setup”, then press ▼ or ENTER and press ▲ or ▼ to select “Time Setup”, press ▶ or ENTER.

2. Press ▲ or ▼ to select “Time”, then press ▶ or ENTER.
   Press ▲ or ▼ to select “Auto Synchronization”, then press ◀ or ▶ to select “Off”.

3. Press ▲ or ▼ to select “Date” or “Time”, then press ◀ or ▶, 0-9 to enter the correct time.

4. Press RETURN to exit the menu.

Power On/Off Timer
This feature allows you to programme the TV to turn on or off automatically at a set time.

1. Press MENU. Press ◀ or ▶ to select “Setup” press ENTER, then press ▲ or ▼ to select “Time Setup”, then press ▶ or ENTER.

2. Press ▲ or ▼ to select “Time”, then press ▶ or ENTER.
   Press ▲ or ▼ to select “Power On Timer” or “Power Off Timer”, then press ◀ or ▶ to select “Off”, “On” or “Once”.
   If you set the “Power On Timer”, you can also set the “Power On Channel”.

3. Press RETURN to exit the menu.

Basic Operation

Channel selection
With the Numbered buttons (0-9). Example

• No. 2: Press 2.
• No. 29: Press 2 and within 2 seconds, press 9.
• No. 929: Press 9, 2, 9 same as above.

Press P + or – to change up or down a channel. This takes approx. 2 seconds. If the auto search only stored 5 stations, only these 5 will appear. Skipped channels will not appear (see P.13).

Channel List

• The Channel List shows a list of all receivable programmes.
• Press CH LIST to display the Channel List.
• Press Yellow to select display details.
• Press ▲ or ▼, then press ENTER to select the desired channel.
• Press CH LIST to display the selected channel.

Information display

Press . The programme information will appear.

If you press twice, and 3 times, more information will appear.
The following figure is an example of DVB-channel reception.

1. Channel Name
2. DVB Teletext available
3. DVB Subtitle available
4. Audio Language
5. Audio Format
6. Video Format
7. Channel Number
8. There are more than 2 pages.
9. Programme Detail
10. Next Programme Duration
11. Parental Rating
12. Programme Duration
13. Programme Title
14. Visual Impaired Audio

Audio/Subtitle language for DVB-channel
If the current watching DVB-channel has more than one audio language or subtitle language, you can change them with AUDIO I/II or .
Press AUDIO I/II several times to select the Audio language.
Press to select the Subtitle language.

Note

• Some DVB-broadcasts may not provide subtitle language service.
• When a DVB-channel with HE-AAC audio is selected, the sound will be output as PCM audio from DIGITAL AUDIO COAXIAL output jack.

Still picture
Press FREEZE to make a still picture. To cancel the still picture, press FREEZE again.

Note

• During still picture mode, Aspect Ratio feature is not available. (If you press PICTURE SIZE, still picture mode will be canceled.)
• During the playback of a movie file in MEDIA mode, still picture function is not available.

Note

• During TV or external input mode, if there is no signal reception, the TV will change to standby after approx. 15 minutes.
• Some functions are activated and de-activated with the same button. Others require RETURN button for de-activating.

Teletext
Teletext is sent page by page. This unit is able to automatically store up to 899 pages, but they can only be accessed once they have been stored. This can take a few moments.

The Teletext language menu allows the installation of the teletext language.
The languages displayed are only those supported by the channel.

Fastext/TOPtext
The Fastext/TOPtext is teletext with a special directory. On the lower part of the screen there are four different coloured fields (red, green, yellow and blue). These fields lead directly to the pages shown within. The coloured buttons on the remote control correspond to the coloured fields. Press the appropriate coloured button in order to activate the desired colour field.

Switch on / off Teletext
Teletext is not transmitted by all channels.
Select a channel that shows teletext.

• Press You will now see a teletext page.
  (If “100” is shown without any text information, it may mean that the channel you have selected does not support teletext.)

• Press again. Teletext and TV picture are shown simultaneously.

• Press again in order to switch off teletext.

• Press again in order to switch on teletext again. The last page which was stored is now shown.

Note
You cannot select any other channels as long as teletext is switched on. Switch teletext off when you want to switch over to another channel.

Select Page

Press P + or – until the page you desire appears. Or
… enter the requested page number by using the 10 Number Buttons.
And if you mistype something, just enter the complete 3-digit wrong page number then enter the desired number again. Or … press one of the coloured teletext buttons so that a page from Fastext/TOPtext is shown.

Hold Pages
Some pages are divided up into subpages by the channel. Subpages are automatically shown in turn, as they are transmitted. In order to hold the page, press . Press again in order to display the next subpage.

Directly Select Subpages
You can directly select the subpages if required. You may use one of two operations.

1. Press in order to select subpage (S ***) is shown. Enter 0 0 0 2. It can take a minute before subpage 0002 appears .Or

2. Wait a few seconds, and the right now available subpages will be shown in the top left of screen. Select your page with  .

Enlargement
In order to enlarge the display, press ****.
Either the upper or lower half of the screen is enlarged. Each time you press you switch between the display of the upper or lower half of the screen or the full picture.

Answering Quiz Questions
Some pages contain quiz questions with concealed answers.
Press in order to show the answers.

Stereo reception in analogue cable TV channel mode
You can see the each signal type of STEREO, Nicam Mono, and DUAL I/II, etc. on the TV-screen when you press .
When 2-channel sound reception is available, you can select your preferred audio with the AUDIO I/II.
Each time you press AUDIO I/II, the sound channel will switch to the alternative channel available.

Note

• In case of bad reception, the stereo sound also can be disturbed.
• The sound multiplex displayed when pressed is user selected sound. It may not the same one which is from the programme being broadcasted.

Remarks on DVB-T system **

**

DVB-T is at present still being developed. You can get information regarding the current stage of development from your specialist retailer.
As a digital service DVB-T basically works differently to previous analogue TV reception.

• Reception Possibilities
  In contrast to cable TV, DVB-T is received via room or roof antennas. A room antenna is sufficient for reception within the reception area of a DVB-T transmitter. A roof antenna may perhaps be necessary for reception in a fringe area. Existing roof antennas may have to be turned in a different direction.
  Contact your specialist retailer to find out about the location of the reception areas or fringe areas. You cannot get DVB-T reception outside the fringe area. Ask a certified antenna specialist for advice on interference with reception. The tuner of this appliance cannot provide active room antennas with operating voltage. Active room antennas have to be equipped with a separate power supply.

• Reception Quality
  DVB-T reception principally either works really well or not at all. There is not a smooth transition with a constant reduction in reception quality. Digital interference occurs at maximum reception range:
  the image freezes, the picture becomes blocky, the sound breaks up or reception cuts out altogether
  at times. If you notice interference with DVB-T reception then this is usually not due to a fault on the TV appliance. Please contact an antenna specialist if you have interference with reception. Inspection of the quality of DVB-T reception is not included in the free warranty to be provided by the manufacturer of the TV appliance.

• Image and Sound Quality
  An individual transmitter transmits up to 4 TV channels on one transmission frequency. This is possible through compression in accordance with the MPEG standard, which is similar to digital data storage on a DVD. The data rate of DVB-T is just a lot lower; at present the max. video bit rate is approx. 4Mbps and the max. audio bit rate is at 256kbps. Visible interference (e.g. blocky picture) can result at extremely low data rates despite there being excellent reception quality within vicinity of the transmitter. Blocky pictures are no fault of the receiver. They are the result of the low data rate transmitted. The digital DVB-T sound can be transmitted to the digital amplifier via the digital output of your TV set.

• Image Format
  Images are transmitted in 4:3 format, 4:3 letterbox format (with black bars above and below the picture) and anamorphic 16:9 format (without black bars). The max. transmitted resolution at present is 704×576.

• Child Lock
  Like DVDs, DVB-T offers can also provide age-restricted access. At the moment, no channels are equipped with this restriction. This appliance does, however, already offer the feature of setting up password protected age restrictions, which only work when the respective programmes are broadcast.

• DVB-T Update
  The DVB-T norm earmarks the transfer of firmware updates. The transfer of firmware updates is called Over Air Download or OAD for short.
  If this product happens to require a firmware update in future, this update could be received via DVB-T. If the available software for updating is detected, the confirmation message whether start the software to download is displayed. The rest please proceed to download-operation according to the directions of a TV screen.
  EPG (Electronic Programme Guide)
  EPG is part of the DVB-signal with 8-days-schedule. This TV can receive and display the EPG-information included into DVB.

Password Setup (Parental lock)

Parental Guidance is a function of the channel provider. If it is not supported by the channel, parental lock is without function. Currently there are no channels supporting parental lock.

1. Press MENU. Press ◀ or ▶ to select “Lock”, then press ▼ or ENTER.

2. Press 0 0 0 0 using the Number buttons (0-9). (This is the default password.)

3. Press ▲ or ▼ to select “System Lock” and press ◀ or ▶ to select “On”, then press ▲ or ▼ to select the desired option. Then press ▶ or ENTER.
   Channel Block: Press ▲ or ▼ to select desired channel, then press ENTER to set Channel Block active/disactive.
   Parental Guidance (DTV mode only): Press or ▶ to select desired Age Rating level (None/4-18).
   Change Password
   New Password
   Enter your chosen new password (please call service, if you have forgotten the new number).

   • Confirm Password
     After you have entered the new password, you need to enter the same password again for confirmation.

   • Clean All : Press ◀ or ▶ to select “OK”, then press ENTER. All settings are return to normal setting.

4. Press RETURN to return the normal screen.

While toggling between channels, if a service which has a parental rating (higher than your setting) and you have set the “System Lock” to “On”, the channel will be locked. The password entering screen
will appear. Then enter the password to view that channel.

EPG (Electronic Programme Guide)
The Guide menu shows the available programme listings for the next 8 days only.

1. Press GUIDE (EPG) to display the Guide menu.

2. Service list :
   Lists all the services that are currently available. As you scroll through the service list by pressing ▲ or ▼.

3. Events list :
   List the events in a grid of rows.
   You can press ◀ or ▶ to navigate through the rest of the events.
   You can easily move to the previous day or next day in the Events List by pressing Red or Green button (the date of the programme information you are currently viewing is shown in the top left hand corner).

4. The “View detail” shows the extended event description of an event.
   Each time you press Yellow, detail text will scroll page down.

   • Detail text will not shown when “System Lock” feature is “On” and selected programme is locked.You should enter the password for display it.
   • To add schedule to schedule list, press Blue. (See more detail on page 23.)

To clear the menu screen, press GUIDE (EPG) or RETURN.

Other convenience functions

Picture
| Picture Mode
| Standard / Vivid / Soft / User| Select the most suitable picture mode according to your lighting condition.
Brightness / Contrast / Colour / Sharpness / Tint|

• You can adjust the picture to your preference.
•  “Tint” is available in NTSC-signal mode or Component/HDMI-signal wilth 60Hz.

Back Light| You can use the Back Light feature to adjust the screen brightness for improved picture clarity.
Color Temperature| Standard (Neutral) / Warm (Reddish) / Cool (Bluish)
Advanced Video
| DNR|

• You can clear up analogue TV signal by reducing the dot noise.
• “Auto” is available only in analogue signal.

| Medium / Strong / Auto / Off / Low
MPEG NR| Similar with the Noise Reduction, you can set to reduce the block noise.
| Low / Medium / Strong / Off
Audio
| Balance / Bass / Treble| You can adjust the sound quality to your preference.
Surround|

• The Surround feature processes the audio signal to expand the listening field wider and deeper to create a ‘pseudo surround-sound’ from the TV’s speakers.
• The feature works with stereo signals from TV broadcast or AV input.

| On / Off
Equalizer| Select the most suitable sound mode according to your watching contents.
| Off / Rock / Pop / Live / Dance / Techno / Classic / Soft
Stable Sound| This will automatically adjust volume so each channel and input has the same average volume level.
| On / Off
Sound Type| You can select your preferred audio with the ◀/▶.
Type| You can set audio output.
| Normal /Visually Impaired| Select type of audio for output .
Visually Impaired|

• You can set the output audio of Visually Impaired audio. Visually Impaired audio is verbal narration inserted to explain detailed scene in parallel with normal audio for people with visual impairment.
• This option is available, when the setting of “Type” above is “Visually Impaired” only. Press ▶ to enter the following options.

| Speaker| On/Off| Select to turn On/Off the Visually Impaired audio.
Volume| You can adjust the audio volume of Visually Impaired audio.
TV
| Country Region ID (Appears only if the selected country is Spain or Portugal)| Set the different time zone for Spain and Portugal.
Channels| See page 12-13.
Schedule List| See page 17, 23.
Selected Items| Setup hint
---|---
Setup
| OSD Language| See page 12.
Aspect Ratio| See page 21.
Blue Screen| You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent.
| On / Off
Time Setup
| Time Zone| If the time displayed on the Channel Information differs from the actual time, adjust the time offset until the correct time zone is shown.

•   Normally, this would be done by selecting “As Broadcaster”.

Time| See page 13.
Sleep Timer| Sleep timer switches the TV to standby after a defined period of time.

To cancel the Sleep Timer, set to “Off”.

| Off / 10 / 20 / 30 / 40

/ 50 / 60 / 90 / 120

Minutes

Auto Sleep| When the Set and Remote button operation are not operated with specified period by this setting (3/4/5 Hours), the power status is changed to stand by mode automatically
| Off / 3 / 4 / 5 Hours
OSD Timer| The OSD is cleared automatically as per this setting.
| None / 5 / 10 / 15 / 30 /

45 /60 S

Subtitle
| Subtitle| On /Off| Select subtitle On or Off.
Digital Subtitle Lang. 1st| Select preferred subtitle language, if the current watching DVB channel has more than one subtitle language.
Digital Subtitle Lang. 2nd| Select second preferred subtitle language.
Subtitle Type| Select the subtitle type (Normal / Hearing Impaired).
Teletext
| Digital Teletext Language|

• First preferred Videotext language can be set here, which is used in case that the currently viewed DVB channel has more than one Videotext Languages.
• If the channel does not have the Videotext language set in “Digital Teletext Language”, the Videotext language is displayed with first receiving language.

Decoding Page Language| Set language for the decoding page.
Audio Language
| Audio Language 1st| Select preferred audio language, if the current watching DVB channel has more than one audio language.
Audio Language 2nd| Select second preferred audio language, if the current watching DVB channel does not have the language set in “Audio Language 1st” option above. If the “Audio Language 2nd” set here is not transmitted in the channel, the first language included in the channel is selected.
Common Interface| You can access the Common Interface module information from this menu option.
•   This unit supports the C.I. card of “Top Up TV” and “Boxer”
Disk Setup| See page 22.
Format Disk| You can format the USB devices.
First Time Installation| See page 11.
Reset Default| Press ▶ or ENTER to enter the Reset Default screen. Press ◀ to select “OK”, then press ENTER. Reset the
TV function will now begin.
Lock| See page 17.

Picture size and resolution

Resolution and picture quality
Broadcast wide screen films in different resolutions. The following table shows the resolution options for wide screen film broadcast media.

| Broadcast media
---|---
Resolution of the wide screen signal| Analogue cable TV| Digital cable TV| DVB-T| Satellite (DVB-S)| DVD| HDTV

Satellite (DVB-S2)

| Blu-ray- Disc
432i x 768 (Letterbox)| Yes| Yes| Yes| Yes| Yes| Yes| No
576i x 768 (anamorphic)| No| Yes| Yes| Yes| Yes| Yes| No
720 x 1280 (HD)| No| Yes| No| No| No| Yes| Yes
1080i x 1920 (HD)| No| Yes| No| No| No| Yes| Yes
1080p x 1920 (HD)| No| No| No| No| No| No| Yes

Best picture quality is achieved when the input signal has a resolution of 1920 x 1080i. If a signal with a lower resolution is input (e.g. analogue cable TV), there is a visibly poorer picture quality.
This is understandable as, if the same picture quality were available at a lower resolution, the broadcasting companies would not need to take the trouble to send the signal at the higher resolution.

Why are there different resolutions?
Analogue cable TV uses a standardised TV signal. Each analogue 4:3- tube TV, however old it is, can process this signal. That is the advantage of standardisation. The disadvantage is that the resolution has not changed since the end of the Second World War. The resolution has been max. 576 x 768 for over 60 years. For comparision: today’s TVs feature a FullHD-resolution of 1080 x 1920.
The analog cable-network offers the 16:9-format at a low resolution of only 432 x 768. This input covers only 16% of a FullHD-screen’s area. 84% of the screen would stay black, if the TV would not make up the rest by some special mathematics. 84% of what you see had been made up artificially by magnifying the tiny input-signal to full-screen-size. That’s the reason for the analog cable-network’s low picture-quality seen on every FullHD-TV.

Picture quality and black bars
Wide screen films come in different formats. The format is the relationship between the width and height of the picture. For example, with a 16:9 film the width to height ratio is 16:9 or 1.78:1. Only 16:9 films can fill a HD-ready screen without black bars. Therefore, black bars are always visible when a format other than 16:9 is received. E.g. 4:3, A 4:3 displays vertical black bars to the right and left.
If a 4:3 picture is increased to 16:9 format then it either appears distorted (see illustration) or some parts of the picture are cropped off at the top and the bottom. This is completely normal and is not a fault in the wide screen TV.
Super Cinemascope films are wider than 16:9 films. They are in the format 2.4:1 or 22:9, for example. This is clearly wider than16:9. Therefore, Super Cinemascope films display black bars at the top and bottom on any HDTV set.

Picture format and resolution
There is no connection between the picture format and the resolution received. For example, the Super Cinemascope format can be received in all resolutions, even in the HD resolution1080ix1920. For HDTV reception too an HDTV set may display black bars at the top and bottom.

Picture format

Picture Size
The required picture format can be set by pressing the PICTURE SIZE button. Press PICTURE SIZE until the required format is displayed.
You move through the following formats when you press the button: Auto, 16:9, 4:3, Zoom1, Zoom2, 1:1 (DTV/HDMI mode only).
Auto (ATV/DTV/AV only)
The picture is automatically only then shown in
a format-filling display when a WSS-TV signal is received.
Example
If the analogue tuner receives a letterbox image with WSS signal then the resulting image looks like this

WSS
Public broadcasters include 16:9 identification, the WSS signal (Wide Screen Signaling), during transmission in order to ensure automatic conversion to 16:9.
Some private broadcasters do not transmit a WSS signal. Automatic does not recognise anything without WSS signal and does not automatically alter the picture size. Use the PICTURE SIZE button to set the required picture size for private channels.
The picture’s size does not follow the WSS properly or the size switches unexpectedly with a faulty input from antenna or channel: this is not the TV’s fault. Countermeasure: Select a fixed-size for those channels manually with the PICTURE SIZE key. Do not set the AUTO position.

• Other formats
  Press PICTURE SIZE until the desired size is reached.

• 16:9
  The width of the picture will be zoomed evenly. 16:9 is particularly suitable for DVD players, DVB-T and satellite receivers, which can transmit and show 16:9 feature films without black bars. In the set-up menu of the set, adjust it to show that a 16:9 TV set is connected.

• 4:3
  The picture is displayed in 4:3 format with black bars to the right and left.

• Zoom1/Zoom2
  The picture is increased.

• 1:1 (DTV/HDMI mode only)
  All images are displayed on the TV screen of 16:9 ratio without  over scanning. This is only a signal of 1920 x 1080 full frame. Other formats (eg. 576p) are smaller, with black border.

Information for recording function

Preparation
Plug-in an external storage device into the USB port.

Note

• The Power indicator of the unit will blink green and red while the recording is in progress. Time shift will not work for ATV or external inputs. You cannot play the recorded programme back on a PC or other device.
• We cannot guarantee compatibility with all USB memory types/brands.
• We do not accept responsibility for loss of files on your USB devices caused by connection to this unit. This TV will only work with FAT16/32 formatted USB devices. This unit is not compatible with NTFS formatted devices for recording function. Recorded video is saved in the following location on your device: [root]/pvr/. You can play back by entering the “Media” menu (See page 24.)
• Do not use a USB extension cable.
• When using the PVR/Media functions the subtitles are set to “Off”. (in order to activate subtitles you will need to change the subtitles setting to On.)
• If you want to display the subtitle of recorded programmes, press .
• Please be advised that if your TV fails to complete your programmed recording due to loss of signal or power there will not be any error message displayed.
• Only use USB Memory or HDD for PVR. A correspondence format is FAT16/32. Recommend the high speed USB device (more than 2MB/s). Connected using a USB Hub is not detected, devices should be connected directly to the TV’s USB port.
• For connect the USB device, please refer the Owner’s Manual provided with your USB device. Use of a USB device capable of operating below 500mA/5V is recommended. This unit is capable of supplying power of up to approximately 0.8A/5V (LT-24HA48E: 1.5A/5V). Should the electricity supply exceed the said amount, power to the connected device may be automatically cut off as a protective measure. For USB devices with large power requirements, use devices that have their own power supply sources.
• Do not connect this product to a non-specified device. It may cause damage to the device and TV.
• When recording or setting up a timed recording, please check to see if your USB memory or HDD has sufficient available memory.
• If the available memory is insufficient, your recording or timed recording may not be executed or may be cut off while recording.

Recording the TV programme
You can record a digital programme (Free view) onto a compatible USB stick or external hard drive.

1. Press REC to start recording. The information screen will appear.
2. To stop recording, press ■ (STOP). Press ◀ or ▶ to select “YES” in the confirmation screen, then press ENTER.

Watch the recorded programme

Press REC LIST. Recorded file list will appear. Press ▲/▼/◀/▶ to select desired file, then start playback with ENTER.
You can use special function for playback. See page 25.

Preparing your USB device for playing Time Shift recordings

1. Press MENU. Press ◀ or ▶ to select “Setup”, then press ENTER. Press ▲ or ▼ to select “Disk Setup”, press ▶ or ENTER.
2. Select “Auto” or “Manual”, then setup your device following the on-screen guide.

Auto setup
Press ▲ or ▼ to select “Auto”, then press ENTER.

The system will execute automatically
“Analyzing” ⇒ “Creating timeshift file” ⇒ “Speed testing” ⇒ Conclusion.

Manual setup
Press ▲ or ▼ to select “Manual”, then press ENTER. Press ▲ or ▼ to select “Format” or “Skip”, then press ENTER.

If you select “Format”, The confirmation screen will appear. Select your desired option, then press ▲/▼ and press ENTER.
After formatting, you will be prompted to select the size of the recording.

Select desired file size and press ENTER to enter the next prompt menu (“Creating timeshift file” ⇒ “Speed testing” ⇒ Conclusion).

Time Shift

You can record a digital programme by using the USB storage device. This function is for your convenience, and allows you to pause/record a live programme for a period of time based on the size of the USB drive inserted.

Preparation
Plug-in an external storage device into USB port.

1. To start recording, press ▶ (PLAY) button. The recording will start and the picture will be paused.
2. To view a recorded programme, press ▶ (PLAY) button again.
3. To stop recording, press ■ (STOP) during viewing a recorded programme, the pop-up will appear select “YES” then press ENTER to confirm stop recording.

EPG Recording

Preparation
Plug-in an external storage device into USB port.

1. Press GUIDE (EPG) to enter EPG Menu Screen press ▲ or ▼ to select the programme which you want to record, then press Blue button to enter the Schedule List page.
   Note
   You can also enter the Schedule List page by press T-REC then press Blue.

2. Press ▲/▼/◀/▶ to select desired option, then press number buttons (0-9) to set date and time.
   Channel number : Press ◀ or ▶ to select channel number, and it will show the channel information below.
   Start date : Set the start date of record / reminder.
   Start time : Set the start time of record / reminder.
   Stop time : Set the stop time of record.
   Schedule type : Select the schedule type (Record / Reminder).
   Repeat type : Select the repeat type (Once / Daily / Week).

3. Make sure the start time is later than the current time, then select “Add” and enter the schedule record list page.
   In the schedule record list page, you can add more schedule by press Blue button, or delete the schedule you had selected by press Red button.

4. When the time is up, you will see the reminder dialog box. Select “YES” to record. Or, no answer about 30 seconds, recording will start.

Note

• Schedule List page also can be displayed by select “Schedule List” in “TV” menu.
• When the TV is in standby mode, and the time to start record, TV will record the programme with no power-on.You can check TV status by power indicator on the front of TV (while recording the programme, the indicator will flash red and green alternately).

Media Operation

1. Connect the USB storage device into the Media Input terminal.
2. Press MEDIA to display the Media menu.

Note

• Do not disconnect a USB storage device while it is being accessed. Doing so can damage the device or the files stored on the device. You can safely connect or disconnect the USB storage device when the TV is not in MEDIA mode. Back up all the data in the USB storage device in case if data was lost due to unexpected accident. We do not assume any liability for the losses by misuse or malfunction.
• Not all USB storage devices are compatible with this TV.
• The character that exceeds the display area is not displayed.
• We cannot guarantee compatibility with all USB memory types/brands.
• Can use FAT16/32 and NTFS (for USB playback only) formatted USB devices only.
• Do not use USB extension cable.
• “tshift” folder is only for Time Shift function. Cannot use in the Media menu.

Media Browser

Media Selection

File Selection

Playback screen

1. Press ◀/▶ to select the desired media type Photo/Music/Video or Text at Media Selection and press ENTER. File selection window will appear.
2. Select folder or file with ▲/▼/◀/▶, and then start the playback with ENTER.

• Press MENU in File selection screen, you can call various operational options. Select the option by ENTER/▲/▼/◀/▶.
• Sort : Select the desired sort type.
• Media Type : Select the desired media type.
• Thumbnail Size : Select the thumbnail icon size.
• Copy / Paste / Delete : You can copy/paste/delete the file. When you delete the file, you cannot recover it!
• Recursive Parser / Normal Parser : Only display all of the files which are associated with the current folder(the folder is photo, music, video or text), such as; if the current folder is photo, only display all pictures in this folder.
• Photo Frame : Press ENTER. Then select “One photo mode” to show only one photo continuously. Or select a folder (eg. C:\) to show all the photos in that folder one by one. Press ENTER to start playback.
• Press MENU. “Sleep time” is shown. Press ENTER, then select length of time to turn off the unit. Off: Playback runs infinitely.
• Press RETURN to exit photo mode.

Playable File Types

AAC-LC (.m4a), HE-AAC

(.m4a), MPEG1 (.mp2), MPEG4 (.m4a)

Video| Container| AVI (.avi), MKV (.mkv), MP4 (.mp4/.m4v), PS (.mpg/.mpeg),
TS (.ts/.tp/.trp), VOB (.vob)
Video Codec| Xvid, MPEG1, MPEG2, MPEG4 SP/ASP, H.264, MJPEG
Audio Codec| MPEG1, MPEG2, MPEG4, AAC, AAC-LC, HE-AAC, PCM/ADPCM, AC3, WMA
Text| Text (.txt)

Playback files

1. Press ◀/▶ to select Photo, Music, Video or Text at Media Selection and press ENTER. File selection window will appear.
2. Select folder or file with ▲/▼/◀/▶, and then start the playback with ENTER.
   Press RETURN to return to Media Selection.

You can playback the files with the following remote control butt

Note
The content will change in accordance with each media setting screen.

Press MENU in Playback screen.You can use various playback operation with appropriate Operation menu. Select the option by ENTER/▲/▼/◀/▶

do not function.

Note
For large image sizes, the display time will be longer than the slide show interval set.

Connecting an HDMI or a DVI device to the HDMI input

The HDMI input receives digital audio and uncompressed video from a HDMI equipped device or uncompressed digital video from a DVI equipped device.
When you connect to a DVI device with a HDMI-to-DVI adapter cable, it only transfers the video signal, so it is necessary to connect the external speaker units to output the audio signals. Select the HDMI input mode (see P.11).

Note

• Please notice the operating manual for the HDMI device to be set up.
• This unit cannot support PC signal from HDMI input.

Connection to other equipment
Attention: Preparation

• Disconnect all equipment from the AC-supply, to prevent any possible damage.
• Make the necessary connections.
• Make sure all connections are safe & secure before reconnecting your equipment the AC-supply.

Note
Select an appropriate external input mode. (See page 11).

1. Connecting a Video camera or Games console to AV
   • Connect Video (Yellow) cable from devices to supplied Mini-pin cable (Green connector). Then connect to the unit.

2. Connecting an digital audio system
   Connect Digital-amplifier to the Digital-Audio-output of the TV-unit with a coaxial digital cable.

3. Connecting to other equipment
   Please make the following settings inside your receiver’s / DVD-player’s setup-menu:
   Video signal : composite (CVBS)
   TV-Format : 16:9
   Volume : MAX
   If you miss to make these settings properly, picture quality will be inferior and parts of the picture might be missing. This is not a fault of this TV-set.
   In case you need help to make this adjustment with your satellite-receiver / DVD-player, please consult the related instructions or contact the supplier or maker of those apparatus for support.
   Please use the satellite’s remote-control handset to select Teletext or desired TV-station. Generally it is not possible to store satellite TV- stations into a standard TV.
   Press INPUT SELECT, select AV. Press PICTURE SIZE several times, until appropriate size is displayed.

4. Connecting to a DVD player or other AV device with Component Video outputs
   If your DVD player (or other device) has Component Video output jacks, use a suitable set of leads (RCA/Phono) to connect these to the Component Video inputs on this TV via supplied Mini-pin cable as shown
   it can greatly enhance the picture quality and performance. Please remember that you will also need to connect separate leads (RCA/Phono) for the audio signals.

Note
The Component Video input of this unit are for use with equipment which outputs interlaced signals (PAL: 576i/1080i or NTSC: 480i/1080i) and progressive signals (PAL: 576p/720p or NTSC: 480p/720p).

Troubleshooting table

Please check the following list before requesting service.

Check that the mains power outlet is properly connected. Select appropriate input mode.
Unplug unit for 1 minute, then plug it back in.| 7

11

No reception| Have you tuned in the TV stations? Press 1 on the remote control.
Connect the antenna.
Make sure the set is ON and not in Standby mode|

10

11

The TV switches off with missing antenna input signal| This is normal.
15 minutes after the antenna signal has disappeared, the set will change to standby mode.|

14

The Channel option cannot be selected.| The unit is set to AV mode. Press 1 on the remote control.|
Wrong Colours| Colour and Brightness errors can occur when the viewing angle/ambient air temperature (see technical specifications) are exceeded.|
While viewing a DVB (digital) channel, there is sound but no picture.| Some channel offers audio content only. It is normal.|
Blocky image or image stops intermittently.| Check all antenna connections.
Move the antenna away from areas of possible interference. Try using an antenna booster.| 10
Some digital channels cannot be viewed.| Contact the service provider to subscribe.|
A cracking sound is sometimes heard from the unit.| If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing very slight contractions in response to changes in the room temperature.
There are no adverse effects on the performance or other aspects.|

The LCD panel is a very high technology product, giving you fine picture details. Occasionally, a few nonactive pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

Specifications

| LT- 24HA48E| LT- 29HA48E| LT- 39HG48E
---|---|---|---
System:

Video Colour System: Preset channels: Frequency Range:

LCD:

HDMI input:

Audio Output Power:

|

• Analogue : PAL (B/G, D/K, I), SECAM (B/G, D/K)
• This product is not compatible with analogue SECAM L broadcasting.
• Digital : DVB-T, DVB-T HD (H.264) PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60Hz
• 4000 Service in total of Analog and Digital
• Analogue : 45.75~858MHz Digital: E2~E69
• TFT low-glass Active Matrix Colour LCD
• HDMI compliant (type A connector), HDCP compliant Suggested scan rates: 50Hz: 576i/576p/720p/1080i/1080p
• 60Hz : 480i/480p/720p/1080i/1080p
• 24Hz : 1080p
• HDMI Audio: 2-channel PCM, 32/44.1/48 kHz sampling frequency 16/20/24 bits per sample

approx. 2.0W (MAX) x 2| approx. 10.0W (MAX) x 2
GENERAL
Power Source:

Energy efficiency class: Visible screen size (diagonal): Power Consumption (Rating):

Power Consumption in on mode:

*Energy consumption per year¹:**

Power Consumption in standby mode:

*Power Consumption in recording standby mode²:**

*Power Consumption in recording mode²:**

Screen resolution:

Weight: Dimensions:

VESA wall mount is required: Surrounding temperature:

Operating Humidity:

| AC 220-240V, 50Hz
B| A
60 cm / 24 in| 72 cm / 29 in| 98 cm / 39 in
45 W| 57 W| 77 W
27 W| 39 W| 54 W
39 kWh| 57 kWh| 79 kWh
0.49 W| 0.29 W
10.4 W| 8.6 W
11.5 W| 9.6 W| 9.7 W
1,366 pixel (horizontal) x 768 pixel (vertical)| 1,920 pixel (horizontal) x 1,080 pixel (vertical)
3.6 kg| 4.7 kg| 10.2 kg
55(W)x37(H)x14(D)cm| 67(W)x43(H)x17(D)cm| 89(W)x57(H)x24(D)cm
100×100 mm (M4x10mm)| 200×100 mm (M6x10mm)
Operation: 5°C ~ 40°C/Storage: –20°C ~ 60°C
Less than 80%RH
ACCESSORIES
2 batteries (AAA/R03/UM-4)/Remote control unit/Base plate/Screws for base plate (4x16mm) LT-24HA48Ex3, LT-29HA48E/LT-39HG48Ex4/Mini pin cable (Y (CVBS)/Pb/Pr)/SCART-RCA Adapter/AV-Cable (CVBS/L/R)

• ¹ Energy consumption per year, based on the power consumption of the television operating 4 hours per day for 365 days. The actual energy consumption will depend on how the television is used.
• ² Based on the power consumption of the television unit only (when TV does not output picture and sound signal). Not include any other USB devices.
  Weight and Dimensions are approximate. Because we continuously strive to improve our products we may change specifications and designs without prior notice.

License information

• The “HD ready” Logo and “1080p” qualifier Logo are trademarks of DIGITALEUROPE.
• DVB and the DVB logos are trademarks of the DVB project.
• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
• This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
• THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR
• THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.
• THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
• All other trademarks are property of their respective owners.

Information on software license
The following open source software component is included in this product

• Posix Compatibility Layer
  Portions of this software is
  CYGPKG_POSIX Copyright © 1990, 1999 The Regents of the University of California.
  All rights reserved.

• MIPS HAL
  Portions of this software is
  CYGPKG_HAL_MIPS Copyright © 1992 The Regents of the University of California.
  All rights reserved.

• Standard C Library
  Portions of this software are
  CYGPKG_LIBC_STDIO Copyright © 1990 The Regents of the University of California.
  CYGPKG_LIBC_STDLIB Copyright © 1990, 1992, 1993 The Regents of the University of California.
  CYGPKG_LIBC_STRING Copyright © 1988 Regents of the University of California.
  CYGPKG_LIBC_TIME Copyright © 1999 Kungliga Tekniska Hogskolan (Royal Institute of
  Technology, Stockholm, Sweden).
  All rights reserved.

Dimension

References

• Tesco Supermarkety | Clubcard, Letáky & Recepty | Tesco
• Tesco Supermarkety | Clubcard, Letáky & Recepty | Tesco
• Tesco - Szupermarket | Clubcard, Újság & Receptek, Bevásárlás | Tesco
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>