DYNOJET 2006-2015 Yamaha FZ1 Power Commander 6 Installation Guide

2006-2015 Yamaha FZ1 Power Commander 6
Installation Guide

PARTS LIST

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

OPTIONAL ACCESSORY INPUTS

Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs.  You can use any open/close type switch. The polarity of the wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important.  Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the  Control Center Software. Once gear position is set up you can alter your map based on gear position and setup gear-dependent kill times when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a  certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about  10mm from its end. Push the wire into the hole of the PC6 until it stops and then tightens the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier

2 2006-2015 YAMAHA FZ1

INSTALLING THE POWER COMMANDER 6

1. Remove the main seat and the passenger seat.

2. Prop the front of the fuel tank up.

3. Remove the bolt on the left-hand side of the fuel tank bracket and loosen the right-hand bolt enough to route the PC6 harness beneath it.

4. Lay the PC6 module in the tail section temporarily.
   Route the PC6 harness through the tail section, towards the engine, beneath the fuel tank bracket, and following inside the left side frame rail.

5. Re-secure the fuel tank bracket.

6. Locate and unplug the stock connector for the Fuel Injector sub-harness.
   This is a GREY 16-pin connector located on the left side of the bike just rear of the air box.
   

7. Plug the pair of connectors from the PC6 wiring harness in-line of the stock Fuel Injector sub-harness connector.
   

8. Attach the PC6 ground wire with the small ring lug the negative (-) terminal of the bike’s battery.
   

9. Using the supplied Velcro, secure the PC6 module in the rear of the tail section.
   Make sure to clean the surfaces with the alcohol swab before attaching.
   You could also use the tool kit strap to hold the module in the tail.
   

10. Confi rm the wiring harness routing is correct and free and clear of any hot or moving parts.

11. Lower and secure the front of the fuel tank and reinstall the seats.

Download the latest map files from our website at dynojet.com/tunes.
Optional inputs:
Speed – PINK wire on WHITE 3-pin connector under the fuel tank.
Engine Temperature – GREEN/WHITE wire of the GREY 16-pin connector (connected to PC6).
12v source for Autotune – BLUE wire of the tail light connector.

2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –800-992-4993 – DYNOJET.COM
© 2006-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED

Documents / Resources

| DYNOJET 2006-2015 Yamaha FZ1 Power Commander 6 [pdf] Installation Guide
2006-2015 Yamaha FZ1, Power Commander 6, 2006-2015 Yamaha FZ1 Power Commander 6, FZ1, FZ1 Power Commander 6
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>