Oben BE-126 Dual Action Ballhead Instruction Manual
- June 16, 2024
- Oben
Table of Contents
Oben BE-126 Dual Action Ballhead
Product Information
Specifications
- Product Name: BE Series Dual Action Ballhead
- Brand: Oben
- Mounting Thread: 1/4 inch
FAQ
- Q: Where can I find more Oben products?
- A: Visit our website at www.obensupports.com for more Oben products.
Introduction
Thank You for choosing Oben!
This sturdy Oben BE Series Dual-Action ballhead provides smooth, effortless operation. Two locks provide independent adjustment and locking of the ball and the panoramic base. A snap-in quickrelease plate is included for quick, simple mounting/ dismounting of the camera. An integrated bubble level ensures accurate alignment of the camera with the horizon. The panoramic base of the ballhead allows for full 360° panning—ideal for shooting panoramic photos.
Please read through this entire manual before using the BE series ballhead.
Note: Images are for illustrative purposes only. Actual product may vary.
KEY FEATURES
- A. Quick-Release Plate
- B. Bubble Level
- C. 1/4”-20 UNC Mounting Screw
- D. Quick-Release Knob
- E. Main Locking Knob
- F. Locking Index Scale
- G. Pan Knob
- H. Panoramic Base With 360° Markings
- I. 90° Groove
OPERATION
Mount Ballhead To Tripod
- To mount the ballhead on the tripod, first tighten all of the knobs on the head.
- Then, being careful to properly align the tripod stud and the ballhead hole to avoid damaging them, rotate the ballhead clockwise onto the tripod, and tighten it by hand.
Converting Mounting Thread
- For tripods with a 1/4″ threaded mounting stud: insert the supplied Reducer Bushing into the threaded mounting hole of the head to enable a proper fit.
Main Locking Knob Operation
The single Locking Knob locks and unlocks the ballhead, which allows you to change the position of the camera. When changing camera position using the Locking Knob, always keep one hand on the camera. Turn the knob counterclockwise to unlock the head and clockwise to lock it. Ensure that the knob is firmly tightened before letting go of the camera.
Mount Quick-Release Plate
Remove the quick-release plate from the ballhead by turning the quick-release knob counterclockwise. This loosens the quick-release clamp, allowing you to remove the quick-release plate. Mount the quick-release plate to the threaded hole on the base of your camera. Use the supplied hex key to tighten the screw. The plate utilizes a 1/4″- 20 screw that will fit most cameras.
Warning
- Some manufacturer’s plates do not meet our specifications and may not lock your equipment securely in the Oben quick-release clamp.
- Please test all camera and lens plates made by manufacturers other than Oben to ensure compatibility.
Mount Camera
- After mounting the quick-release plate to your camera, ensure that all knobs except for the quick-release knob are tightened on the ballhead.
- Loosen the quick-release knob by turning it counterclockwise until it stops.
- Mount the camera to the ballhead by sliding one edge of the quick release plate into the ballhead, then lower the other side until the quick-release plate is lying flat in the quick-release clamp. Turn the quick-release knob clockwise to lock the plate.
Warning: Always use one hand to secure the camera while adjusting the ballhead, and ensure that the lock is engaged before letting go of the camera.
Panoramic Base
The base of the ballhead can be independently rotated 360°. The base is controlled by loosening the pan knob. This is the smallest knob, at the base of the head. Twist the knob counterclockwise to unlock the base, rotate the base to the desired position, and lock the base by turning the knob clockwise. Degree markings on the base of the ballhead can be used to accurately set up panoramic shots.
Warnings
- Do not exceed the ballhead’s maximum load capacity (see packaging for details).
- Ensure that all appropriate locks are engaged when necessary.
- Ballhead should only be used in temperatures ranging between -22° and 140° F. Do not operate in saltwater. Dry ballhead if it becomes wet.
- Remove the camera from the ballhead during setup or transport.
- Keep out of reach of children.
Visit our website at ObenSupports.com for more Oben products.
© Copyright 2013 The Gradus Group
All other trademarks are the property of their respective owners
References
- Oben | Tripods, Monopods & Tripod Accessories
- Oben | Tripods, Monopods & Tripod Accessories
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>