LOPOLIGHT 200-014 Series 2NM 360 Degree Red Black Anodized Installation Guide
- June 16, 2024
- LOPOLIGHT
Table of Contents
LOPOLIGHT 200-014 Series 2NM 360 Degree Red Black Anodized
Product Information
- Specifications:
- Part Number: P/N 601-324 Rev 2.00
- Supply Voltage: Any DC voltage between 10 and 32 volts (12- and 24-volt systems)
- Recommended Fuse or Circuit Breaker: Less than 2A (slow)
- Mounting:
- To mount the Lopolight product, follow these steps:
- Go to www.lopolight.com or use the QR code provided to access the “products” section.
- Find the datasheet, which includes the dimensional drawing, for your specific product.
- Ensure proper alignment to the vessel centerline.
- Open or close the light as illustrated, making sure the lock screw engages correctly.
- Connecting Power:
- To connect power to the Lopolight product, follow these guidelines:
- Cabled Lights:
- Red Wire: Positive (+)
- Black Wire: Negative (-)
- For Double Lights: Use two cables with the same color coding.
- Light with Green Connector:
- Single Light:
- Pin 1: Positive (+)
- Pin 2: Negative (-)
- Pins 3-5: Not used
- Double Light:
- Pin 1: Positive (+)
- Pin 2: Negative (-)
- Secondary Light:
- Pin 4: Positive (+)
- Pin 5: Negative (-)
- Pin 3: Not used
- Ensure the recommended fuse or circuit breaker is used (less than 2A, slow).
- Grounding: Do not connect the navigation light housing to the ground (Earth). It is recommended to connect the cable screen to the ground (Earth). Route the cabling away from sources of heat and large inductive fields, such as electric motors, to avoid chafe.
- Cleaning Your Product:
- To clean your Lopolight product, follow these steps:
- Ensure the product is disconnected from power.
- Use a soft cloth or sponge dampened with water or a mild detergent to gently clean the product’s surface.
- Rinse the cloth or sponge and wipe off any remaining detergent.
- Dry the product thoroughly before reconnecting to power.
- Troubleshooting:
- If the light does not function, please check the following:
- Ensure the power supply voltage is within the specified range (10-32 volts DC).
- Check the wiring connections, making sure the polarity is correct (avoid accidentally wiring the polarity wrong).
- End-of-Life Signaling:
- Your Lopolight product is equipped with a microprocessor that ensures the light maintains the required intensity over a projected lifetime of 50,000 hours. The product will signal when it is nearing the end of its useful life. The following signals may be observed:
- [Signal 1]
- [Signal 2]
- [Signal 3]
- Warranty:
- Lopolight provides a warranty for their products. For warranty inquiries and claims, please fill out the form at www.lopolight.com, under the Warranty tab.
- Approvals:
- The light in this package is type-approved to the following standards:
- [Standard 1]
- [Standard 2]
- [Standard 3]
FAQs
- Q: Where can I find the dimensional drawing for my Lopolight product?
- A: You can find the dimensional drawing on the Lopolight website under the “products” section or by using the provided QR code.
- Q: What is the recommended power supply voltage for the Lopolight product?
- A: The Lopolight product can be powered by any DC voltage between 10 and 32 volts (12- and 24-volt systems).
- Q: How should I connect the power cables for a double-light setup?
- A: For a double light setup, the primary light should be connected using Pin 1 (Positive) and Pin 2 (Negative). These secondary lights should be connected using Pin 4 (Positive) and Pin 5 (Negative). Pin 3 is not used.
- Q: What should I do if the light does not function?
- A: If the light does not function, please check the power supply voltage and wiring connections. Ensure the polarity is correct and there are no accidental wiring errors.
Installation
- Thank you for purchasing a Lopolight product.
- Our products are built to ensure a long lifetime in the most extreme marine conditions.
Mounting:
- Go to www.lopolight.com. or use the QR code to get to the ‘products’ section where the datasheet, which includes the dimensional drawing, is found.
- The alignment to the vessel centerline is very important.
- The light is opened/closed as illustrated, please ensure the lock screw engages correctly.
Connecting power:
- Supply Voltage: Any DC voltage between 10 and 32 volts. (12- and 24-Volt systems)
Cabled lights:
- Red wire: Positive (+)
- Black wire: Negative (-).
- ( Double light: 2 cables, same color coding)
Light with green connector:
- Single light:
- Pin 1: Positive (+)
- Pin 2: Negative (-) (pin 3-5: not used)
- Double light:
- Primary light:
- Pin 1: Positive (+)
- Pin 2: Negative (-)
- Secondary light:
- Pin 4: Positive (+)
- Pin 5: Negative (-) (pin 3 not used)
- Recommended fuse or circuit breaker: Less than 2A (slow).
- Grounding: The navigation light housing should not be connected to the ground (Earth). (We recommend that you connect the cable screen to the ground (Earth).
- Cabling: Avoid chafing and route it away from sources of heat and large inductive fields such as electric motors.
- Cleaning your product:
- Wipe off your product with a normal detergent, on a damp cloth DO NOT use alcohol or thinner for cleaning your light – this could damage the lens.
Troubleshooting
- If the light does not function:
- Check that you have a supply Voltage between 10 and 32 Volt DC.
- Check that the polarity is right (you will not damage the Lopolight by accidentally wiring the polarity wrong).
End-of-life signaling:
Your Lopolight product has a microprocessor inside that ensures that the light has the required intensity over a 50.000-hour projected lifetime. The light will signal to you when it is getting to the end of its useful life. The following signals can be observed:
- All OK: 5 seconds after turning on the light it will go dark for 0,1 second and turn on again. This is just a check for you to ensure that the microprocessor is working.
- Less than 2000 working hours left: The dark period is extended to 2 seconds: you should change the light at your next service within the next 12 months.
- Light Expired: The dark period is extended to 5 seconds: You should change the light immediately. (The light will still be working, even in the expired state)
Warranty
- This product is covered by our 5-year limited warranty.
- If you want to claim a warranty for your product, please fill in the form at www.lopolight.com, under the Warranty tab.
Approvals:
- The light in this package is type-approved to the following standards:
- EN-14744, UL-1104, COLREG72, IEC 60945
- Recognized by the following authorities:
- IMO, MED (EU-wheelmark), USCG
- P/N 601-324 Rev 2.00 / 06 April 2022
- Lopolights with 2-core cabling or green connector
- P/N 601-324
- Rev 2.00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>