LOPOLIGHT 300-138-PRO-I Double Stacked Ice Class Masthead Light Installation Guide

June 13, 2024
LOPOLIGHT

LOPOLIGHT 300-138-PRO-I Double Stacked Ice Class Masthead Light

Product Information

  • Product Name: Lopolight

  • Part Number: 601-322

  • Revision: 2.00

  • Supply Voltage: Any DC voltage between 20 and 32 volts (24 Volt systems)

  • Recommended Fuse or Circuit Breaker: Less than 2A (slow)

  • Grounding: The navigation light housing should not be connected to ground (Earth). It is recommended to connect the cable screen to ground (Earth).

  • Cleaning: Follow the instructions provided below for cleaning your Lopolight product.

  • Troubleshooting: If the light does not function, refer to the troubleshooting section for assistance.

  • End of Life Signaling: The Lopolight product has a microprocessor inside that ensures the required intensity over a projected lifetime of 50,000 hours. The light will signal when it is nearing the end of its useful life.
    Warranty: For warranty details, please visit the Lopolight website and fill out the warranty form under the Warranty tab.

  • Approvals: The light in this package is type approved to the specified standards.

Product Usage Instructions

  1. Mounting:

  2. Visit www.lopolight.com. or use the QR code provided to access the “products” section and find the datasheet with the dimensional drawing.

  3. Ensure proper alignment to the vessel centerline. This is crucial for mounting.

  4. If horizontally mounted, open/close the lights as illustrated. Make sure the lock screw engages correctly.

  5. Connecting Power:

  6. Red wire: Positive (+)

  7. Black wire: Negative (-)

  8. In case of double light, both cables have the same color.

  9. Single light:

  10. Pin 1: Positive (+)

  11. Pin 2: Negative (-)

  12. Pins 3-5: Not used

  13. Primary light:

  14. Pin 1: Positive (+)

  15. Pin 2: Negative (-)
    Secondary light:

  16. Pin 4: Positive (+)

  17. Pin 5: Negative (-)

  18. Pin 3: Not used

  19. Cabling:

    •   * Avoid chafing and route the cable away from sources of heat and large inductive fields such as electric motors.
  20. Cleaning Your Product:

Follow the manufacturer’s instructions provided in the user manual for cleaning your Lopolight product.

Thank you for purchasing a Lopolight product. Our products are built to ensure a long lifetime in the most extreme marine conditions.

Mounting

  • Go to www.lopolight.com. or use the QR code to get to the ‘products’ section where the datasheet, that includes the dimensional drawing, is found.
  • The alignment to vessel centerline is very important. Horizontally mounted lights are opened/closed as illustrated. Please ensure lock screw engages correctly.

Connecting power

  • Supply Voltage: Any DC voltage between 20 and 32 volts (24 Volt systems).

Cabled lights:

  • Red wire: Positive (+) Black wire: Negative (-).(Double light: cables, same colour)LOPOLIGHT-300-138-PRO-I-Double-Stacked-Ice-Class-Masthead-Light-FIG-1 \(3\)

Light with green connector:

  • Single light: Pin 1: Positive (+) Pin 2: Negative (-) (pin 3-5: not used)

Double light:

  • Primary light: Pin 1: Positive (+) Pin 2: Negative (-)
  • Secondary light: Pin 4: Positive (+) Pin 5: Negative (-) (pin 3 not used)
  • Recommended fuse or circuit breaker: Less than 2A (slow).
  • Grounding: The navigation light housing should not be connected to ground (Earth). (We recommend that you connect the cable screen to ground (Earth)).
  • Cabling: Avoid chafe and route it away from sources of heat and large inductive fields such as electric motors.

Cleaning your product

  • Wipe off your product with a normal detergent, on a damp cloth.
  • DO NOT use alcohol or thinner for cleaning your light – this could damage the lens.

Troubleshooting

If the light does not function:

  • Check that you have a supply Voltage between 20 and 32 Volt DC.
  • Check that the polarity is right (you will not damage the Lopolight by accidentally wiring the polarity wrong).

End of life signaling:
Your Lopolight product has a microprocessor inside that ensures that the light has the required intensity over a 50.000-hour projected lifetime. The light will signal to you when it is getting to the end of its useful life. The following signals can be observed:

  • All OK: 5 seconds after turning on the light it will go dark for 0,1 second and turn on again. This is just a check for you to assure that the microprocessor is working.
  • Less than 2000 working hours left: The dark period is extended to 2 seconds: you should change the light at your next service within the next 12 months.
  • Light Expired: The dark period is extended to 5 seconds: You should change the light immediately. (The light will still be working, even in the expired state)

Warranty

  • This product is covered by our 5-year limited warranty.
  • If you want to claim a warranty for your product, please fill in the form at www.lopolight.com, under the Warranty tab.

Approvals: The light in this package is type approved to the following standards:

  • EN-14744, UL-1104, COLREG72, IEC 60945

Recognized by the following authorities:

  • IMO, MED (EU-wheelmark), USCG

P/N 601-322 Rev 2.00 / 06 April 2022 24 Volt Lopolights P/N 601-322 Rev 2.00

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals