HELLA ONYX.SWITCH Radio Wall Transmitter Instruction Manual
- June 5, 2024
- HELLA
Table of Contents
HELLA ONYX.SWITCH Radio Wall Transmitter
Preliminary remarks ONYX.SWITCH
With this HELLA product, you have opted for a high-quality product with a most up-to-date technology that can nevertheless be easily installed and operated. In these instructions, we describe the basic use of the wall-mounted radio transmitter ONYX.SWITCH. The following symbols will assist you with the installation or use and require safety-conscious conduct:
Attention!
- This symbol indicates instructions that, if disregarded, can put the user in danger.
- This symbol indicates instructions that, if disregarded, can potentially result in damage to the product.
- This symbol indicates instructions for use or helpful information.
- This symbol requires you to act.
- This symbol indicates parts of the product, for which you will find important information in these installation instructions.
General notes
Questions
In case of questions concerning the installation or the use of your product,
please consult your authorized specialist shop.
Warranty
Warranty claims are subject to statutory limitation periods. Service parts are
excluded from the warranty; the same applies for changes in colour and changes
in characteristics caused by UV radiation.
Liability
Should the notes and information given in these instructions be disregarded or
if the product is misused or used for the wrong purpose, the manufacturer
declines the guarantee for damage to the product. In these cases the liability
for consequential damage to any parts or persons is ruled out as well
Legal notes
The graphs and texts of these instructions were carefully prepared. We cannot be hel liable for any errors and their potential consequences! Subject to technical modifications to the product and to these instructions! These instructions include copyrighted information. All rights reserved! The listed product or brand names are trademarks of the respective owners.
EC declaration of conformity
The HELLA Sun and weather protection technology GmbH hereby declares that thi
product complies with the basic requirements and the other applicable
regulations of th EC directives. The complete declaration of conformity can be
found in the download area of our website https://www.hella.info.
Safety instructions
The safety instructions as well as the appropriate instructions must be read
carefully before installation and use. In case of non-observance of the
directions and information given in these instructions and in case of improper
installation and operation or unintended use, the manufacture shall not accept
any warranty claims concerning any damage to th product. In these cases the
liability for consequential damage to any parts or persons is ruled out as
well.
- Follow the described installation steps and pay attention t recommendations and notes.
- Keep these instructions in a safe place.
- Observe the regulations for prevention of accidents of the employer’s liability insurance association!
- Before operation check the unit for visible damage. If the unit is damaged, it should not be used; please consult authorized specialist staff immediately.
- Only use unmodified original parts from HELLA.
- In case of unauthorised opening of the device, improper use, incorrect installation or incorrect operation, there is a risk of damage to personsor property.
- Never let children play with the unit.
- Never randomly press the pushbuttons of your wall-mounted radio transmitter when the sun protection element is not within your sight.
Observance of regulations and rules
The building owner is responsible for the observance of statutory rules and country-specific provisions on site If the wall-mounted radio transmitter ONYX.SWITCH is mounted nearby a junction box/flush-mounted box, a junction plane must be provided by the customer! ONYX.SWITCH may not get in contact with a 230 V AC voltag circuit!
Scope of delivery
The following components are included in the scope of delivery:
- Wall-mounted radio transmitter ONYX.SWITCH without frame
- Mounting plate
- Mounting material
- CR2032 Battery (already inserted)
Device description
- ONYX.SWITCH
- Art.-No. 50680601
- 868MHz/ 2.4GHz
ONYX.CLICK is a 5-channel wall-mounted radio transmitter which can be used in
combination with all ONYX control devices/sensors. In addition, the wall-
mounted radio transmitter can quickly and easily be linked to the ONYX smart
home control system wit ONYX.CENTER. As ONYX.SWITCH works bi-directionally,
feedback signals by the contro commands are directly displayed on the wall-
mounted radio transmitter. The wall-mounted radio transmitter ONYX.SWITCH is
compatible with all standard designs of the 55 mm frame systems
Legend
- O UP (tilting)
- DOWN (tilting)
- Group pushbutton
- Pushbutton with heart symbol
- Status/channel bar
- Battery compartment
- QR QR code
Technical data
| Power supply | 3V DC CR2032 lithium battery (230mAh) |
|---|---|
| Operating time of the battery | 3 years |
| IP rating | IP20 |
| Permitted storage temperature range | -20 °C to +70 °C |
| Permitted operating temperature range | 0 °C to +60 °C |
| Radio frequency | 868,3 MHz/2,4 GHz band |
| Transmission power | 12.6 mW (868.3 MHz) |
2.5 mW (2.4 GHz)
Channels| 5
Device per channel| 5 (there are no restrictions on the number of devices per
channel when used in
combination with ONYX.CENTER)
Dimensions LxWxH| 55 x 55 x 9.5 mm
Weight| 20 g
Installation
- Fix the mounting plate. The mounting material enclosed may be used for this.
- Place the frame onto the mounting plate.
- Press the wall-mounted radio transmitter ONYX.SWITCH in the frame and in the mounting plate.
Configuration
Before configuring ONYX.SWITCH, download HELLA’s free “ONYX” app from the App store / Google Play to your smartphone. Bluetooth must be activated at your smartphone to configurate the wall-mounted radio transmitter ONYX.SWITCH. Bluetooth is not necessary for the later operation of the wall-mounted radio transmitter.
Configuration of ONYX.SWITCH without ONYX.CENTER
Open the “ONYX” app. Now press the group button (3) and the heart button (4) together on the wall-mounted radio transmitter for 3 seconds. The wall-mounted radio transmitter appears in the app and can be selected. Then follow the instructions on the screen. “Settings for motor and pushbuttons” can usually be adopted. When using a weather sensor you should activate the respective sensor for each taught-in control unit. As soon as the first control device/the first weather sensor has been taught in, you can add additional control devices with “+”. Only after the connection of all control devices/ sensors, go to “←” on the top left. Now tap on one of the 5 groups and assign the devices as you like. The configuration is completed with “Done”. You can close the app now. If, after the configuration of the ONYX.SWITCH, your shading elements move into the wrong direction, connect the wall-mounted radio transmitter with the app “ONYX” as described above. Under “Configure devices” you now can tap on the pencil symbol of the respective device (top right). Under the menu item “Advanced settings” tap now on “Reverse direction of rotation”. By tapping on “Done” these settings are adopted. To actuate your shading unit brightness dependent, tap under “Configure devices” on the pencil symbol of the respective device (top right). Under the menu item “Advanced settings” you find the item “Brightness range “. Here two ranges can be adjusted via the two scroll bars. Both ranges can be assigned the action “Extend” or “Retract”. These settings can only be made, if a weather sensor ONYX.WEATHER is available. You can find additional information regarding the adjusting possibilities at the control device in the respective “Instructions for use”.
Configuration of ONYX.SWITCH with ONYX.CENTER
First of all, ONYX.CENTER must be configured completely according to the “Instructions for use” enclosed. As described in the respective instructions for use, all control devices and sensors must also be connected to ONYX.CENTER. Now connect with ONYX.CENTER. The “Configuration mode” in the app must be activated. You find it under “Settings”. ONYX.SWITCH can be taught in under “Devices” and “+”. Then follow the instructions on the screen. The configuration is completed with “Done”. Wall-mounted radio transmitters ONYX.SWITCH are only visible in the app “ONYX”, when the “Configuration mode” is active. If you want to adjust the configuration at the wall-mounted radio transmitter, activate the “Configuration mode”. You find it under “Settings”. Then tap on the respective ONYX.SWITCH. The groups can be adjusted under “Advanced settings”.
Operation
- With the two pushbuttons UP (1) and DOWN (2) you can extend or retract your shading element with a click on the relevant latching pushbutton. Outdoor blinds are tilted with a brief click. If the respective latching pushbutton is pressed for 2 seconds, the outdoor blind raises or lowers. With a brief click on the respective pushbutton the lighting is switched off or on. By pressing the respective pushbutton for 2 seconds, the lighting i dimmable, if it is combined with the matching ONYX control device. Successfully transmitted control commands are displayed by a backlight i the status/channel bar in the corresponding channel colour.
- With the group pushbutton (3) you can change over to other channels, which you configured earlier in the app “ONYX” (see chapter Configuration). The fixed assigned channel colour is displayed in the status / channel bar (5).
- With the pushbutton with heart symbol (4), one favourite position per channel can be saved, which is then ready for later use. Press this pushbutton for 3 seconds to save the selected position. With a brief click on this pushbutton, the position saved before can be accessed again.Successfully transmitted control commands are displayed by a backlight in the status/channel bar in the corresponding channel colour
Replacing the battery
- To replace the CR2032 button cell, remove the battery from the battery slot (6) on the back of ONYX.SWITCH.
- Use a pointed object (e.g. pencil) to remove the button cell from the battery slot. When replacing the battery, please observe the correc alignment of the battery in the battery slot (6) (when inserting the button cell, the + pole must be aligned towards the top).
Ideal use of the radio signal
- In case of bad reception, the position of the ONYX.SWITCH must be changed.
- Radio systems that send on the same frequency may cause interference with reception.
- It must be considered that the range of the radio signal is limited by statutory regulations and structural measures.
Fault removal
| Problem | Possible cause | Troubleshooting |
|---|---|---|
| Status/channel bar flickers red | CR2032 Battery is empty | Replace the CR2032 |
battery as
described in point “Replacing the battery”
No backlight in the status/channel bar. ONYX.SWITCH is
inoperative.
| Battery CR2032 is empty or is inserted in the wrong direction| Open the
battery slot , check the battery and replace it, if necessary, or turn it
around
No backlight in the status/channel bar when pressing the pushbutton
“Favourite position” (4)
| A favourite position has not been configurated yet| Teach-in the favourite position as
per point “Operation”
Drive runs in the wrong direction| Directions were interchanged when connecting the motor
cable
| Perform the reversal of the direction in the “ONYX” app as per point
“Configuration”
The backlight in the status/channel bar shows red when giving
a control command
| Unfavourable position of the ONYX.SWITCH,
poor or no radio reception
| Reposition ONYX.SWITCH or control device slightly
Backlight in the status/channel is
rainbow-coloured
| ONYX.SWITCH is not configurated yet| Configure ONYX.SWITCH as per
point “Configuration”
Status/channel bar flashes in the channel colour, the shading product is extended and retracted by a few
centimetres
| One or more control devices from the respective group are locked due to a possible wind alarm| Wait until the wind has weakened, afterwards the respective control device is released after 15 minutes
Disposal
Dispose of the device in accordance with the current country-specific
regulations for electronic scrap (e.g. suitable collecting points). According
to the current regulations, batteries are to be disposed of at the retailer or
the municipal collection points.
HELLA Interior Venetian Blinds
regulate the lighting in a room very comfortably, immediately gracing it with
much more atmosphere.
HELLA Insect screens
and you decide who is allowe to come in and who isn’t.
HELLA Pleated Blind
folds up very compactly and protects very well against the sun and nosey
glances where only little space is available.
HELLA Outdoor Blinds
serve for the light regulation, as view protection, anti-glare blind and heat
protection.
HELLA Front-mounte Roller Shutter
for more safety and protection against rain, wind, heat, the cold, noise,
incident light and nosey glances, also available for subsequent installation
HELLA Facade Awning
with toggle catch mechanism for a lovely facade design with perfect heat and
glare protection.
For questions, wishes and ideas:
- HELLA Infoline +43/(0)4846/6555-0
- HELLA Sonnen- und Wetterschutztechnik GmbH
- A-9913 Abfaltersbach, No. 125
- Phone: +43/(0)4846/6555-0
- Fax: +43/(0)4846/6555-134
- e-mail: office@hella.info
- Internet: http://www.hella.info
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>