WHIRLPOOL UXT52 Range Hood User Guide
- June 16, 2024
- Whirlpool
Table of Contents
WHIRLPOOL UXT52 Range Hood
Product Information
Specifications
- Model Numbers: UXT20, UXT30, UXT40, UXT41, UXT42, WVU37U
- Switch Types: Two-Speed (with rocker switch), Intermediate (with rotary switch), Three-Speed (with push buttons)
- Electrical Requirements: 120-volt, 60 Hz., AC-only, 15-amp fused electrical circuit
- Tools Needed: Wire stripper, #2 Phillips screwdriver, Flat-blade screwdriver
- Parts Needed: UL Listed/CSA Approved wire connectors, 1/2 (13 mm) strain relief, UL Listed #14 (minimum) 3-wire cable
Installation Instructions
WARNING: Electrical Shock Hazard. Disconnect the power before
installing the light switch. Electrically ground the range hood and light
switch by connecting the ground wire to the ground screw in the switch box.
Replace all parts and panels before operating. Failure to do so can result in
death or electrical shock.
Mounting the Switch Box
Mount the switch box on the wall in an easily accessible area 15 (38 cm) to
40 (1 m) above the floor. Avoid reaching over the cooking surface. For a
single-pole toggle light switch, install a 3 1/2 (8.9 cm) deep single-gang
switch box.
Attaching the Power Cable
Attach the power cable to the switch box. Clamp wiring to switch box and
unit using a UL Listed or CSA Approved 1/2 (13 mm) strain relief. Provide 6
(15.2 cm) leads inside the box and fan for easier wiring.
Connecting Wiring
General instructions for all models:
-
* Make sure both the single pole toggle light switch and the range hood are properly grounded.- Make sure the ground wire is securely fastened to the single pole toggle light switch ground screw. Tighten the ground screw.
- Use proper wire nut sizes for the number and size of wires.
- Tighten screw terminals.
- Make electrical connections, following the appropriate diagram.
Mounting the Single Pole Toggle Light Switch
Mount the single pole toggle light switch in the switch box. Tuck wires
into the switch box and fasten the control to the box using the attached
screws.
Attaching the Switch Plate
Fasten the switch plate to the control using the short screws from the
parts bag.
Setting Fan Speed and Light
Set the fan speed and light on the range hood to your preference. The light
switch will turn the range hood on and off using your settings.
For questions about features, operation/performance, parts, accessories, or service, call: 1-800-253-1301. In Canada, for assistance, installation, and service, call: 1-800-607-6777. Residential range hoods can be installed to comply with Sections 308 and 309 of ADA Guidelines when used with appropriately mounted controls installed at 15″ (38.1 cm) to 40″ (101.6 cm) above the floor, and control access should not require reaching over a cooking appliance. The following range hoods can work in an ADA- compliant situation when the range hood is wired to operate from a dedicated standard electrical wall switch. To facilitate this application, share the information on the following pages with your electrician when preparing for the installation.
NOTE
All the models can be controlled only by one remote switch. The switch
activates or deactivates the motor and the light of the hood.
INSTALLATION REQUIREMENTS
**Tools and Parts
**
Tools Needed
Parts Needed
Electrical Requirements
Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A copy of the above code standards can be obtained from:
-
National Fire Protection Association
-
1 Batterymarch Park
-
Quincy, MA 02169-7471
-
CSA International
8501 East Pleasant Valley Road -
Cleveland, OH 44131-5575
-
A 120-volt, 60 Hz., AC-only, 15-amp fused electrical circuit
WARNING
Electrical Shock Hazard Disconnect power before installing the light switch. Electrically ground the range hood and light switch by connecting the ground wire to the ground screw in the switch box. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.
- White wires (N)
- Black wires (L)
- UL Listed wire connector
- Green (or bare) ground wire
- Home power supply cable #14 UL Approved cable
- Range hood cable
- UL Listed or CSA Approved 1/2″ (13 mm) strain relief
- Green ground screw
- UL Listed single-pole toggle light switch
-
Mount the switch box on the wall in an easily accessible area 15″ (38 cm) to 40″ (1 m) above the floor. Avoid reaching over the cooking surface. For a single-pole toggle light switch: Install a 31/2″ (8.9 cm) deep single‑gang switch box. Attach the power cable to
-
the switch box. Clamp wiring to the switch box and unit using a UL Listed or CSA Approved 1/2″ (13 mm) strain relief. Provide 6″ (15.2 cm) leads inside the box and fan for easier wiring.
-
Connect wiring.
General instructions for all models- Make sure both the single pole toggle light switch and the range hood are properly grounded.
- Make sure the ground wire is securely fastened to the single pole toggle light switch ground screw. Tighten the ground screw.
- Use proper wire nut sizes for the number and size of wires.
- Tighten screw terminals.
- Make electrical connections, following the appropriate diagram
-
Mount a single-pole toggle light switch in the switch box. Tuck wires into the switch box and fasten the control to the box using the attached screws.
-
Attach the switch plate.
-
Fasten the switch plate to the control using the short screws from the parts bag.
-
Set the fan speed and light on the range hood to your preference. The light switch will turn the range hood on and off using your settings.
© 2017 All rights reserved. Used under license in Canada Tous droits réservés. Utilisé sous licence au Canada.
FAQ
Q: What are the electrical requirements for the range hood?
A: The range hood requires a 120-volt, 60 Hz., AC-only, 15-amp fused electrical circuit
Q: What tools are needed for installation?
A: You will need a wire stripper, a #2 Phillips screwdriver, and a flat-blade screwdriver.
Q: How should I mount the switch box?
A: The switch box should be mounted on the wall in an easily accessible area 15 (38 cm) to 40 (1 m) above the floor. Avoid reaching over the cooking surface.
Q: How do I connect the wiring?
A: Make sure both the single pole toggle light switch and the range hood are properly grounded. Make sure the ground wire is securely fastened to the single pole toggle light switch ground screw. Use proper wire nut sizes for the number and size of wires. Tighten screw terminals. Make electrical connections following the appropriate diagram.