SENCOR SFN 4040 Stand Fan Instruction Manual

: June 16, 2024
: SENCOR

Table of Contents

SFN 4040 Stand Fan
WARNING
GENERAL DESCRIPTION
OPERATION INSTRUCTION
Operation
Oscillation
Positioning
Height adjustment
Cleaning
TECHNICAL FEATURES:
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
Documents / Resources

Stand Fan
Instructions Manual

SFN 4040 Stand Fan

SENCOR SFN 4040 Stand Fan SFN 4040

WARNING

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they will not play with the appliance.
Extreme precaution should be exercised when using any type of domestic appliances, especially the followings:
Read the instructions in conjunction with the illustrations before using for the ﬁ rst time and only use the appliance as described in the operation instructions.
Before you plug the appliance in, check if the voltage speciﬁ ed on the appliance corresponds to the mains voltage in your home.
Never plug in the appliance before it is completely installed.
Never operate the appliance with a cracked or damaged blade.
For your own safety and that of others: water and electricity are a dangerous combination! Do not use the appliance in the immediate surroundings of a bath, a shower or a swimming pool.
Do not use the appliance if the electrical cable is damaged or whenever any possible internal failure or incorrect operation has been detected.
The use of any electrical connections that are unauthorized or different from those supplied with the appliance could cause operational failure or short circuits.
Do not hold the electrical cable in hands and make sure it is not caught between furniture or any other object.
To prevent the possibility of short-circuit, do not place the appliance on window-sills.
Make sure that the electrical cable and plug cannot come in contact with water or humidity. Do not spray the appliance with any liquid.
Unplug the appliance by holding the plug; do not pull on the electrical cable.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualiﬁed person in order to avoid a hazard.
Disconnect the appliance from the power supply if it is to be moved or not to be used for a long time.
Exercise extreme care whenever the appliance is to be used by, or near, children.
Keep the appliance away from reach of children. Do not allow children to play with it. In case this appliance gets into the hands of children, injury or damage to the appliance could be incurred.
Do not use the appliance in explosive or inﬂ ammable environments.
Do not place the appliance near a naked ﬂ ame, stove or heater.
Always place the appliance on ﬂ at, dry surface.
Never immerse any part of the appliance in water or any other liquid.
Do not use the appliance without the protective grilles.
Do not attempt to force the grilles to turn or to stop.
Never put objects into the grilles when the appliance is connected to the mains.
It is not advisable to expose people (esp. babies or older people) to a continuous cold air stream for a long time.
Do not use the appliance outdoors.
This appliance is for domestic use only and should not be used industrially.
Always send the appliance to ofﬁ cial repair services for either mechanical or electrical repairs.

GENERAL DESCRIPTION

SENCOR SFN 4040 Stand Fan - GENERAL DESCRIPTION

A – Front guard
B – Front/rear guard ﬁ xing screw
C – Fan blade cap
D – Fan blade
E – Rear guard lock nut
F – Rear guard
G – Holes
H – Motor shaft
I – Round pins
J – Motor unit
K – Oscillation knob
L – Fan body| M – Speed selection knob (rotary)
N – Body set screw
O – Inner pipe
P – Height Adjustment Screw
Q – Outer pipe
R – Base Bar
S – Base Cap
0 – Stop (o.)
1 – Low speed
2 – Medium speed
3 – High speed
---|---

OPERATION INSTRUCTION

Assembly (ﬁ g. 1)

Loosen and remove the four screws from the base bars “R”.
Cross the two base bars as shown in ﬁg. 1 and align the four holes with those on the ﬂ ange.
Secure the ﬂ ange to the base bars “R” with the four screws.
Slide the base cap “S” down to cover the screws.
Pull up the inner pipe “O” from the outer pipe “Q” and hold it tightly by tightening the height adjustment screw “P”.
Mount the fan body “L” to inner pipe “O” and hold tightly by tightening the body set screw “N”:
Unscrew (turn counter-clockwise) the rear guard lock nut “E” from the shaft end of the motor unit “J”.
Mount the rear guard “F” onto the front of motor unit “J” by matching the positioning holes “G” on rear guard to the positioning round pins “I” on the front of motor unit.
Push in ﬁ rmly until the pins protrude through the holes.
Secure the rear guard “F” to the motor unit “J” with the rear guard lock nut “E”.
Insert the fan blade “D” onto the motor shaft “H”. Be sure that the pin in the shaft is matched with the slot on the fan blade.
Press ﬁ rmly until the fan blade stops. Secure the fan blade “D” with the fan blade cap “C”, turning counter-clockwise to tighten.
Test the fan blade “D” operation by rotating it with your hand. There should be no friction with the rear guard lock nut “E”. If the blade does not rotate freely, disassemble and repeat the procedure.
Attach the front guard “A” (with the guard ring) to the rear guard “F”.
Join the front/rear guards by pressing ﬁ rmly (“Click”).
Secure the two guards by the ﬁ xing screw “B”.

Operation

After checking the voltage, plug the appliance into the mains.
Select the operating speed by turning the speed selection knob “M” to “1” (low speed), “2” (mid speed) or “3” (high speed) (ﬁ g. 3).
To stop, set the speed selection knob “M” to “0”.

Oscillation

Press the oscillation knob “K” at the upper part of motor housing downward to start oscillation during operation (ﬁ g.2).
Pull the oscillation knob “K” upward to stop oscillation (ﬁg.3)

Positioning

The direction of the air stream can be adjusted in vertical direction:
Move the motor unit “J” upward or downward to alter the vertical angle (ﬁ g.4). You will hear a clicking sound while positioning.

Height adjustment

Loosen the height adjustment screw “P” and adjust the fan to the desired height by pulling upward or downward the inner pipe “O” (ﬁ g.5). Be sure to hold tightly the fan body while loosening the screw.
Tighten the height adjustment screw “P” after the adjustment.

Cleaning

Always remove the mains plug from the wall socket before cleaning.
Clean with a soft, dry or damp cloth, if required with a soapy detergent. Do not use abrasives or solvents.
Before removing the protective grilles make sure the appliance is disconnected from the power supply.

TECHNICAL FEATURES:

220 – 240 V ~ 50 Hz, 50 W
Protection class: II
Noise level: 52 dB (A)
The declared noise emission level for this appliance is 52 dB(A), which represents level A of the acoustic power relative to the reference acoustic power of 1 pW.

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS
Dispose of packaging material at a public waste disposal site.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES

** The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this product at your applicable collection point for the recycling of electrical & electronic equipment waste. Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product. The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health, which could be caused as a result of improper liquidation of waste. Please ask your local authorities or the nearest waste collection centre for further details. The improper
disposal of this type of waste may fall subject to national regulations for ﬁnes.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the correct disposal method from local government departments or from your seller.
** This product meets all the basic EU regulation requirements that relate to it.
Changes to the text, design and technical speciﬁ cations may occur without prior notice and we reserve the right to make these changes.

Copyright © 2012, Fast ČR, a.s.
Revision