NIXON 01 Portable Wireless Speaker User Manual

NIXON 01 Portable Wireless Speaker User Manual

LISTEN

BIGGER, BETTER, LOUDER, PROUDER AND ALL WITHOUT ANY BOTHERSOME WIRES OR CORDS TO GET IN YOUR WAY. MOBILE PORTABILITY BUILT TOUGH TO WITHSTAND THE ELEMENTS TO TAKE IT ANYWHERE. GRAB IT AND GO TO A HOUSE-PARTY, SKATE PARK, SNOW PARK OR BEACH – ALLWITH BLUETOOTH®” CONNECTIVITY MEANS THERE ARE NO LIMITS TO WHERE IT CAN GO.

ECOUTE

PLUS GRAND, PLUS FORT, PLUS CLASSE…BREF,  MEILLEUR. ET TOUT CELA SANS AUCUN FIL OU CORDON ENCOMBRANT. CONGU POUR ETRE MOBILE ET ROBUSTE, FAIT POUR RESISTER AUX ELEMENTS, TU PEUX LEMPORTER PARTOUT. SORS AVEC : DANS UNE SOIREE, UN SKATE-PARK, UN SNOW-PARK OU A LA PLAGE – GRACE A SACONNECTIVITE BLUETOOTH? TU PEUX ALLER QU TU VEUX, SANS AUCUNE LIMITE

IMPORTANT SAFETY INFORMATION

The Blaster, although rugged, is not bulletproof, waterproof or indestructible.
Failure to use common sense while enjoying The Blaster may cause permanent damage to the speaker, yourself and/or others.

• DO NOT expose to excessive moisture. This includes water, beer, any other liquids, or super wet environments. To clean, wipe down dirty surfaces with a lightly damp cloth then let dry. Do not use chemical cleaners or run directly under water.
• DO NOT expose to extreme high or low temperatures.
• DO NOT expose to direct sunlight, fire or other direct heat sources.
• DO NOT expose to extreme pressure, shock or impact.
• DO NOT attempt to open or disassemble.
• DO NOT dispose of in household garbage due to chemical battery contents. Please follow in accordance with your local laws and regulations.

FEATURES

-Wireless Bluetooth connectivity with most smartphones and computers Seamless rubber construction with built-in resistance to dirt and moisture Precision-tuned acoustics for big, full sound and ultra-low distortion -Rechargeable battery with extra capacity for up to 12 hours of continuous play -On-board volume and playback buttons for remote control of your music -Integrated microphone for hands-free wireless voice calls on most smartphones -Auxiliary stereo input to connect wired only devices with included audio cable

TECHNICAL SPECS

• Bluetooth v2.1 + EDR, A2DP, AVRCP, HFP, HSP
• Supported Codecs : AAC, apt-X
• Wireless Range : 10m (33 ft)
• Output Power : 3W RMS x2
• Frequency Response : 80-20,000 Hz Charging Input: DC 5V 500mA, DC 5V 1A
• Dimensions : 21.85 x 9.5 x 4.5 cm
• Weight : 525g

BLUETOOTH® COMPATIBILITY

Compatible devices must support Bluetooth v2.1+EDR or higher. Please consult the user manual of your music device or contact the manufacturer for specific compatibility information.

**CONTENTS

**

POWER IT UP

hold 2 seconds

Press and hold the Power Button for 2 seconds then release to power ON The Blaster.
The Power LED will illuminate solid red.

Press the Power Button again for 2 second then release to power OFF.

TIP: The Blaster will Power OFF automatically after 10 minutes of no music playback to save the remaining battery.

SYNCITUP

hold 2 seconds

Press and hold the Multi Button for 2 seconds then release to enter Bluetooth Pairing Mode, indicated by flashing blue LED.

TIP : When powered ON, the Blaster will reconnect automatically to the nearest known music device. Alternately, it will enter Bluetooth Pairing Mode if no known music device is found.

Locate the Bluetooth settings on your music device, enable Bluetooth, and select “NIXON BLASTER” from the list of local Bluetooth devices.

When Bluetooth® pairing is successful, the blue LED will illuminate solid.

TIP : Avoid sound dropouts by keeping the battery charged and staying within a reasonable wireless range (10 meters or less).

If your music device does not support Bluetooth connections, use the included audio cable to play music directly to The Blaster.

TIP : The remote control buttons and internal microphone will not function when using the AUX input.

CRANK IT UP

Use the Volume Up and Volume Down buttons to set the playback level of The Blaster.

TIP : Because the volume control buttons of The Blaster do not control the volume output of your music device, you must properly adjust the volume settings of each device independently.

If the sound is distorted, decrease the volume setting on your music device first, then set the volume level of The Blaster. A low battery can also cause the sound to become distorted, so it is important to keep a healthy charge.

TIP : Listening at lower volumes can significantly extend battery life.

To disable the various sound effects prompts, hold the Volume Down button with the Power Button when you power ON on the Blaster. To enable the sounds again, hold the Volume Up button with the Power Button next time you power ON.

hold 1 second

SWITCH IT UP

You can control many functions of your music device directly from The Blaster when connected via Bluetooth.

PLAY/PAUSE
NEXT TRACK
PREVIOUS TRACK
FAST-FORWARD HOLD
REWIND HOLD

TIP : When you first power ON The Blaster and reconnect to your music device, simply pressing the Multi Button will begin music playback from where you last stopped.

TALKITUP

You can also use The Blaster as a “speakerphone” when connected via Bluetooth. Incoming and outgoing calls will automatically pause music playback, then resume when the call is ended.

ANSWER CALL
REJECT CALL    2 SECONDS
END CALL
REDIAL    =

Press both volume buttons at the same time to MUTE the microphone during a call. The two LEDs will alternate flashing to let you know MUTE is enabled. Press both buttons again to UNMUTE the microphone playback, then resume when the call is ended.

TIP: The internal microphone is designed to pick up your voice from a reasonably short distance (1m). It is not necessary hold The Blaster close to your mouth.

CHARGE ITUP

Connect the USB Charging Cable between The Blaster and a USB port on a notebook or desktop computer, or use the included USB to AC adapter. While charging, the Power LED will flash in a repeating pattern to indicate the current battery status as shown on the next page.

When charging is complete, the Power LED will stop flashing and illuminate solid if The Blaster is already powered ON, or turn off completely if The Blaster is powered OFF.

TIP : A full charge will take about 6 hours when connected the USB port of a computer. However you may use a 3rd-party USB-to-AC adapter (commonly included with smartphones to reduce the charge time to only 3 hours. Check that your adapter has an output rating of 5V at 1000mA (1A).

BATTERY CHECK

**Press

**

Press the Power Button once then release. The Power LED will turn off briefly, and then flash in a repeating pattern to indicate the battery status. In addition to the flashing lights, a voice prompt will tell you your battery power level.

TIP: Because the volume control buttons of The Blaster do not control the volume output of your music device, you must properly adjust the volume settings of each device independently.

TIP : You can also see the battery in the Status Bar of Apple iOS devices when connected via Bluetooth.

When the battery is LOW, the Power LED will change from RED to YELLOW while powered ON.

TIP : The Battery Check function is most accurate when music playback is stopped.

POWER RESET

In the rare case that your speaker becomes unresponsive, press the small Reset Button using a pen to perform a hard power reset. It is located directly above the micro-USB port.

TIP: Such unresponsiveness is typically caused by compatibility issues with specific versions of mobile device operating systems. To avoid, make sure your device is always using the latest software version.

RESTORE FACTORY SETTINGS

To clear the internal memory of all known paired devices and reset the software to factory default, press and hold the four top control buttons simultaneously until you hear a tone. Then to complete the process, Power OFF and then Power ON the unit.

CONTACT

To find a service center close to you
Go to: nixon.com
Select your country/support/service
Nixon will involve you returning the defective goods to us, at your expense.

WARRANTY

Nixon offers a limited warranty on defects in materials and workmanship for a period of one (1) year after original purchase from an authorized Nixon dealer. This means that if the materials in your speaker aren’t right or if it isn’t put together correctly, we’ll repair or replace it, at our option. But, this doesn’t mean you can abuse your speaker and expect us to fix it for free. We don’t cover normal wear and tear or blown speakers, cut cords, scratches and gouges, loss or theft. You will void your warranty if you disassemble your speaker or if you submerge it into liquids. This includes lava, the ocean, beer or other wet substances.

Problems? You can return the product to the store of purchase and they will initiate the warranty claim and return the product to Nixon for you. Alternatively, if you would like to return the product directly to us, please contact your closest Nixon Service Center and we’ll get you a Return Authorization number and provide you with instructions on how to initiate service. Headphones sent back to us without a Return Authorization number will not receive service. Any claim made under this warranty directly with Nixon will involve you returning the defective goods to us, at your expense.

SPECIFIC TO NIXON SPEAKERS SOLD IN AUSTRALIA

Our goods come with guarantees that cannot be excluded from the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality or the failure does not amount to a major failure.

Australia Warranty Contact Info:
NIXON AUSTRALIA
Nixon Pacific Pty Ltd
1 Billabong Place
Burleigh Heads QLD 4220 Australia

FCC COMPLIANCE AND ADVISORY STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or locate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet apparel s’accorde avec Industry Canada licence-exempte RSS standard.
(1) cet apparel ne peat pas causer intervention, et (2) cet apparel droit accepter de intervention, y comprise intervention qui peat causer l’opération non desire de.
This Class B digital apparatus complies with Canadian ICES-003. Cet apparel numérique de la classed B Est conformed à la normed NMB-003 du Canada.

Under Industry Canada regulation this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Hereby, Nixon, declares that this is incompliance with the essential requirements and other relevant provisions of Directive 1999/5/EC

References

• Nixon US | Watches, Backpacks and Premium Accessories
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>