NB1TX Nooie Baby Monitor User Manual

Nooie Baby Monitor
User Manual

In the Box

Camera

Monitor

Getting Started

Step 1: Long-press the power button for 3 seconds to power on the monitor.

the monitor cannot be turned on due to low battery, please charge it first.
Step 2: Plug in the camera and wait for its LED to turn solid white (live view activated), and the LED will automatically switch off after one minute.

If step 2 doesn’t work, please refer to “Operation & Features”> “Manual Setup” to set it up manually.

Step 3: Place the camera where you can adjust the view to your preferred angle while prioritizing the safety of the baby.

Maintain a minimum distance of 3 feet (10 meters) between camera and the baby to avoid electrical and wire-related hazards.

Operation & Features

Status Icons

(from weak to strong)
| Signal Strength
(from weak to strong)
| Camera Auto-Rotation

Manual Setup

Step 1:

1. Short-press the camera’s pair button while plugged-in.
2. Confirm that the LED indicator is flashing white rapidly. Step 2: 1. Press the menu button on the monitor.
   2. Navigate to “Live View “Add Camera.”
   3 .Select “Start Pairing” to begin “Searching..” The monitor will start pairing to the camera for one minute. If connection fails, please repeat steps 1 and 2.
   Step 3: Successful pairing will grant you access to the camera’s live view on the monitor. 1.Repeat these steps to connect additional cameras. You can pair up to 4 cameras with each monitor.
   2 The monitor can simultaneously display live feeds from 2 cameras.

Power ON/OFF the Monitor

To power the device on or off, press and hold the power button for 3 seconds.

To activate sleep mode or awaken the screen, press the power button once.

Reset the Monitor

Press and hold the reset button for 3 seconds using a pin to reset the device to its factory settings.

This will restore the monitor to its factory settings and unlink the connected cameras. Please refer to “Operation & Features”> “Manual Setup” to add cameras manually after a reset.

Extending & Retracting the Antenna

When extending the antenna, ensure it’s pulled to the highest fixed point for secure placement. Conversely, when retracting the antenna, push it down to the lowest fixed point.

Extending the monitor’s antenna will improve the camera’s signal reception.

Camera Rotation

Rotate the camera by using the navigation buttons on the monitor while viewing its live feed.

camera rotation cannot be controlled in the multi-view mode.

Operation & Features

Temperature Alarm
By enabling the temperature alarm, you can effectively monitor your baby’s environment and ensure their comfort.

Setup Method

1. Press the menu button .
2. Navigate to “Settings “Temp Alarm.”
3. Activate the temperature alarm.
4. Specify the desired maximum and minimum temperature thresholds.

Sound Detection

With sound detection activated, you will promptly receive notifications if any unexpected sounds are detected in your baby’s surroundings. The device comes preconfigured with high sensitivity, which can be tailored to your specific requirements.

Setup Method

1. Press the menu button
2. Navigate to “Sound Detection”1[][.
3. Adjust the sensitivity based on your needs.
   If you would rather not receive notifications, simply deactivate the sound detection.

Multi-View

When multiple cameras are added to the monitor, you can watch the live streaming from two cameras simultaneously.

Setup Method

1. Press the menu button .
2. Navigate to “Live View’ “Multi-View”
3. Select the cameras (up to 2).

In multi-view mode, use the left or right button to choose the camera if you wish to use the two-way audio feature.
Other features, such as camera rotation and music, are notcesible in this mode.

Music
Setup Method 1

1. Press and held the music button for 3 seconds to start playing music
2. Click the music button switch (6 songs in total).
3. Press and hold the music button for 3 seconds to stop playing.

Setup Method 2

1. Press the menu button. .
2. Navigate to ‘Music’ .
3. Choose a track or set it on repeat.
4. Press and hold the music button for 3 seconds to stop playing.

Two-Way Audio
Hold down the “Zoom/Two-Way Audio” button till the monitor screen displays “Speak Now.” Let go of the button to stop.
Zoom
Press the “Zoom/Two-Way Audio” button ( )to toggle between 1x, 2x, and 4x zoom ratios.
You can easily rotate the camera at any zoom level by using the navigation buttons on the monitor.

Troubleshooting

The monitor cannot be turned on.

1. Charge the monitor, press and hold the power button for 3 seconds.
2. If it still doesn’t power on, please refer to “Operation & Features” for instructions on resetting the device.

The camera cannot be turned on.

Please ensure you are using the provided adapter and power cord.
Additionally, verify that your power source is functioning. When the camera is connected to power, it should turn on automatically, and you’ll see its LED flashing in white.
Disconnected devices.
Connectivity issues may arise from the considerable distance between the monitor and the cameras. To ensure a more reliable connection, we suggest bringing them closer together.
The monitor is not displaying live feed or sound.

1. Ensure that the devices are within close proximity, as excessive distance can cause connectivity issues.
2. Check if the monitor has entered sleep mode; if so, you can wake it up by pressing the power button.
3.  Increase the volume by adjusting the volume control.

The live view turned black and white.
When the camera detects low ambient light, it automatically switches to night mode, displaying the feed in black and white. To revert to color mode, increase the ambient light in the camera’s vicinity.

The live view is flickering.
To address any flickering in the live feed, synchronize the camera’s frame rate with the power frequency of your country or region by following these steps:

1. Press the menu button
2. Navigate to “Settings” “Frame Rate.”
3. Choose the suitable frame rate:
   60Hz: Canada, United States 50Hz: China, Europe, Japan

Specifications

Transmission Technology
Radio Frequency Range: 2400 MHz- 2483.5 MHz
Number of Connectable Cameras: Up to 4
Camera
Input: 5V 1A
Antenna Interface: 2.4G External Antenna
Field of View: Horizontal 75° ± 5°, Diagonal 95° ± 5°
Lens Resolution: 1280720 pixels
Speaker: 4ohm 2W
Operating Temperature: 14°F -122°F (-10°C- 50°C)
Temperature Alarm Range: 32°F – 104°F (0°C – 40°C)
Monitor
Input: 5V 1A
Power: 100-240V-50/60Hz 150mA
Battery Capacity: 4000mAh
Charging Speed: 7 hours for a full charge
Screen: 5-inch TFT Display with a resolution of 1280720 pixels
Frame Rate: 50Hz/60Hz
Screen Time: Up to 9.5 hours

Caution

• Store and operate the product within a temperature range of 32°F to 104°F (0°C to 40°C).
• Avoid mounting the camera directly above the baby to prevent accidental falls.
• Maintain a minimum distance of 3 feet (10 meters) between the camera and the baby to avoid electrical and wire-related hazards.
• Prevent direct and prolonged contact of the device with a child’s skin to avoid the risk of burns.
• Utilize the provided adapters, and do not attempt to replace the battery.
• Avoid using the device in humid environments such as bathtubs or near water faucets to prevent water damage and malfunction.
• If the device will not be used for an extended period, please disconnect the power.
• This product is designed to assist with daily baby care and should not substitute for the parental responsibility of child supervision.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party.Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting tocomputer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement for Camera:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Specific Absorption Rate (SAR) information:
This Nooie baby monitor meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.
The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Nooie baby monitor has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the phone kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of the phone. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
RF Exposure Statement for Monitor :

ISED STATENMANT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

RF Exposure Statement for Monitor:
Specific Absorption Rate (SAR) information:
This Nooie baby monitor meets the government’s requirements for exposure to radio waves. The uidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. ISED RF Exposure Information and Statement the SAR limit of Canada(ISED) is 1.6 W/kg averaged over one gram of tissue. Device types: Tablet has also been testedagainst this SAR limit. This device was tested for typical body-worn operations with the back of theNooie baby monitorkept 0mm from the body. To maintain compliance with ISED RF exposure requirements,use accessories that maintain an 0mm separation distance between the user’s body and the back of the Tablet . The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with ISED RF exposure requirements, and should be avoided.

This product complies with the radio interference requirements of the European Community.

Declaration of Conformity

Hereby, Nooie LLC declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
This product can be used across EU member states.
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for Nooie and accessories is -20C-50C.
When charging, please place the device in an environment that has a normal room temperature and good ventilation.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Wi-Fi Operating Frequency Range: 2.4-2.4835GHz (2.4G) 2.4G Wi-Fi Max Output Power: 16.42dBm (TRP for Nooie);
The following importer is the responsible party (contact for EU matters only)
Importer: WSJ Product LTD
Importer Address: Eschborner Landstrasse 42-50, 60489 Frankfurt, Germany
The following importer is the responsible party (contact for UK matters only)
Importer: WSJ Product LTD
Importer Address: Unit 1 Alsop Arcade, Brownlow Hill, Liverpool L3 5TX, GB
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.This product is designed and manufactured with high quality
materials and components which can be recycled and reused.

Contact Info & Warranty

Customer Care
Hey, did we forget something?
Check out the FAQ on our website: help.nooie.com
Need more help?
Contact us at support@nooie.com

Social Media
Would you like to stay informed about our newest products?
Follow us on social @nooiehome

Warranty
12-Month Warranty
24n customer service
Lifetime Technical Support

Designed in USA
Made in China

Documents / Resources

| nooie NB1TX Nooie Baby Monitor [pdf] User Manual
NB1TX Nooie Baby Monitor, NB1TX, Nooie Baby Monitor, Baby Monitor, Monitor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>