Shenzhen Youshida High Technology YS-203 Wireless Karaoke Speaker User Manual
- June 5, 2024
- Shenzhen Youshida High Technology
Table of Contents
Shenzhen Yoshida High Technology YS-203 Wireless Karaoke Speaker
Parts and controls
- Power/Pause
- Mode
- Previous track/Volume-
- Next track/Volume+
- Change tone
- Echo effect
- Reverb effect
- Vocal cut
Bluetooth name: YSD Speaker
Button function details
Power/Pause: Press and hold to turn on/off the power. Press to pause or
play the music.
Previous track/Volume- & Next track/Volume+: Press to choose the
previous/next track. Press and hold to adjust the volume.
Mode button : Press to switch between Bluetooth mode, USB flash drive
mode, MicroSD (TF) card mode and AUX mode.
Vocal cut: Press to remove vocals from a song leaving only the background
music.
Reverb/Echo sound effects: Press to choose the corresponding sound
effect. The default is the Echo sound effect.
Change tone : Press to switch between original, male, female, child,
magic sound effect.
How to use
Sing by Bluetooth
- Turn on the speaker: Press and hold the power button to turn on the speaker. The BT indicator will start flashing.
- Bluetooth connection: Turn on the Bluetooth on your smart phone. In the Bluetooth setting, find the device name “YSD Speaker” and pair. The speaker will make a tone if the pairing is complete and the BT indicator will be continually on.
- Turn on the microphone: Press and hold the power button on the microphone. The microphone will be connected to the speaker automatically and the corresponding indicator on the speaker will be on.
- Adjust sound effect: Adjust the volume of the speaker and microphones and choose appropriate sound effects.
- Play music: Open a music app on your smart phone and play any music you like. The volume of the music can also be adjusted on your phone. Pressing the Vocal Cut button can remove vocals from the song.
Note: Once you pair the speaker with your smart phone by Bluetooth, they
will pair automatically when the next time you use.
The Bluetooth can be disconnected in the Bluetooth setting on your phone.
How to charge
- When the battery is low. The device will shut down automatically.
- Connect a DC 5V charger to the charging connector to charge the speaker or microphones. The charging indicator will turn red when charging and turn off when fully charged.
- It will take about 3 hours to fully charge the speaker and 1 hour to fully charge the microphone. After that they can work for 3-5 hours.
Parameters
Frequency range: 20Hz-20kHz
Max sound level: >115dB, 1kHz, THD<1% Power supply: Built-in lithium-ion
battery Charging voltage: DC SV
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>