Perfit Liner Soft Roll Up Truck Bed Tonneau Cover User Manual
- June 16, 2024
- Perfit Liner
Table of Contents
Soft Roll Up Tonneau Cover
User Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING
- The following precautions must always be observed to minimize the risk of injury.
- Liability will not be accepted for damages resulting from improper usage or failure to comply with these instructions.
- Keep all packaging materials away from children, as they can pose risks such as suffocation or dangers.
- Children or pets are never permitted to remain on the tonneau while the cover is closed.
- Do not modify the product in any way, modification may affect the quality and the reliability of the product.
- Do not stand, sit, or ride on the cover, or use cover or its framework to tie the cargo.
- The cover does not prevent moisture and dust from entering the tonneau. Special wrapping or packaging of the contents may be necessary to keep the cargo clean and dry.
TIP
For the TOYOTA / NISSAN / JEEP UTILITY TRACK.
- Press down side rails firmly when tightening the front screws after step 9 , so that the water resistance will be better.
ITEM LIST
INSTALLITION GUIDE
These items will need to be installed manually.
-
Wipe and clean the tonneau before installation. If there is a gap between the front and side of bulkhead, adhere the seal strip(D) to the front bulkhead and align both ends equally.
-
Place the cover assembly (A) on the front end of the truck bed.
-
Slide 3 Upper clamps (figure H-1) into each of side rail.
If the side rail have Breach, insert the upper clamp (figure H-2) into the side rails channel at step 6.
For the TOYOTA / NISSAN /JEEP UTILITY TRACK -
For the TOYOTA / NISSAN / JEEP UTILITY TRACK, slide 2 Upper Alu Slider (J) into each of side rail.
-
Place one side rail (B/C) on the truck bed and slide into the channel of cover assembly (A), proceed to tighten the set screws on both corners to secure the connection, Repeat the same process for the other side.
-
Position the end of the side rails (B & C) (the side with block) close to the tailgate, ensuring the frame of truck bed cover is properly positioned to avoid readjustment.
-
Insert the lower clamps(I) into the truck bed rail lips, tighten loosely upper & lower clamps with long screws(E).
• If you can not insert the lower clamps(I) as the images shown due to utility track, Pls follow Step 7-1 and 7-2.
7-1. Insert convex slider(L) into the utilit side tracks (on both sides of the tonneau). -
Release the buckles on the both sides of cover assembly, then unroll the cover completely from the bulkhead towards the tailgate.
-
Make sure the crossbars lay on the side rails, push down the rear latch into the slots of side rails. Lift the cover upwards at both ends to check whether the cover is secured completely.
• If the gap between the locking clip and the block of the
side rail is too large, please back to Step 6 (or Step 7-2) to loosen screws,
re-adjust the position of said rails (B&C) and make the distance between B & C
smaller.
• If the locking clip hit the block of the side rail, please back to Step 6 (or Step 7-2) to loosen screws, re-adjust the position of said rails (B&C) and make the distance between B & C wider.
• After all these, tighten sliders/Traps and screws from back to front.
• The side rails may not necessarily align with the sides of the truck.
TROUBLESHOOTING – UNLATCHING
- Ensure the gap between the locking clip and the block of the side rail is as close as possible. The tailpiece of the cover will not latch properly if the gap is too large.
- If the gap between the locking clip and the block of the side rail is too large, please back to Step 6 (or Step 7-2) to loosen screws, re-adjust the position of said rails (B&C) and make the distance between B & C smaller.
- If the locking clip hit the block of the side rail, please back to Step 6 (or Step 7-2) to loosen screws, re-adjust the position of said rails (B&C) and make the distance between B & C wider.
TENSION CONTROL SYSTEM
- How to adjust the tension control system
- To adjust the tension, loosen the both screws on each tension control systems, slide the mechanism forth or back according to the scale. Suggest only one increment per time.
CLEANING AND MAINTENANCE
CLEANING
- Clean the cover and vehicle in a shaded place like under a tree or in an open garage.
- Flood the cover with water to remove surface grit that will scratch the finish when wiped. Wash the cover with cool, clean water and a mild soap. Use a hose, rinse the cover well, making sure to remove all traces of soap and wipe off excess water using a sponge.
- Hose down the entire truck to prevent soap from streaking your truck’s paint finish. Do not use chemicals like detergents, dish washing liquids, bleaches, harsh cleansers, strong cleaners, dry-cleaning solvents, or any other strong chemicals as a cleanser.
- Using a white all-cotton towel, wash the entire cover with the cleaner. Never spot clean the cover to avoid rings or bright spots on the product. Make sure that you only use a soft cotton cloth or sponge as a cleaning tool.
- Do not use rough, abrasive cleaning pads because these can scratch the vinyl, creating pores that allow dirt and other unwanted particles to stick.
- Do not use vinyl protectants that contain petroleum, silicone, or citrus-based additives.
MAINTENANCE
- Check the components regularly to make sure all screws and bolts are tightened.
- Keeping the cover taut: Periodically or as needed, pull the cover tight across width of the truck bed and secure the hook-and-loop fastener on the side rails.