CANDY CTS6CEXWIFI chimney cooker hood User Manual

: June 4, 2024
: Candy

Table of Contents

CANDY CTS6CEXWIFI chimney cooker hood User Manual
INTRODUCTION
- Thank you for choosing this cooker hood.
SAFETY PRECAUTION
Electrical Shock Hazard
Electrical Installation
Direct Connection

CANDY CTS6CEXWIFI chimney cooker hood User Manual

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.
The cooker hood uses high quality materials, and is made with a streamlined design. Equipped with large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation.
Hereby, Candy Hoover Group Srl declares that the radio equipment is in compliance with Directive 2014/53/EU and with the relevant Statutory Requirements (for the UKCA market).
The full text of the declaration of conformity is available at the following internet address: www.candy-group.com.

SAFETY PRECAUTION

Never let the children operate the machine.
The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose.
The cooker hood and its filter should be clean regularly in order to keep in good working condition.
Clean the cooker hood according to the instruction manual and keep the unit from danger of burning.
Forbid the direct baking from the gas cooker. Please keep the kitchen room a good convection.
Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only.
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels;
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels;
Regulations concerning the discharge of air have to be fulfilled.

This appliance if not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person slide for their safety.
Children should be supervised to ensure that they do not play with the appliance.

Do not flambé under the range hood.
CAUTION: Accessible parts may become hot when used with cooking appliance

Electrical Shock Hazard

Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.
Failure to follow these instructions can result in death, fire, or electrical shock.

Electrical Installation

All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.
The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
WARNING: This is a Class I appliance and MUST be earthed This appliance is supplied with a 3 core mains cable coloured as follows:

Brown = L or Live
Blue = N or Neutral
GreenandYellow=EorEarth

Standard Installation Accessories List

INSTALLATION （wall mounting）

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or inflammable material with an interior diameter of 150mm)

Before installation, turn the unit off and unplug it from the outlet.
The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect.
Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws provided.

For inclined panel Modeleed to drill 2x8mm extra holes & fixing screws & screw plugs before installation. Voor schuine modellen
Leave up the cooker hood and hang onto the wall bracket hook.
Fix the one-way-valve to the air outlet of the cooker hood. Then, attached the exhaust pipe onto the one-way-valve as shown below.
i. Place the glass in appropriate position on the top the cooker hood.
ii. Fix with 4 screws and washer. In order to avoid the glass cracking, please do not tighten the screws too strongly.
i. By Put the inner chimney into outer chimney .Then pulling out the inner chimney upwards. Adjust to reach the height required.

ii. Sliding the chimney to adjust the chimney height. When the height you required is reached, then hang the fixing hole to the fixing screws as showed in below pictures.

i. Drill 2 x 8mm holes to accommodate the plate II. Screw andtighten the plate II onto the wall with 2 screws provided.
ii. Assembly the chimney onto the unit and fix it with 2 screws.

Standard Installation Accessories List

INSTALLATION(AIR DEFLECTOR FOR T-SHAPE,CURVED GLASS,FLAT GLASS MODELS):

Air deflector is mentioned as included and not optional

Before installation,curve both ends of the bracket as shown below:
Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws provided.
Drill 2 holes to accommodate the wall plugs,then screw and tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.
Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:
.Install the chimney to the unit and fix it.

o “Please kindly be noted: T-shaped plastic outlet and v-flaps can not be use
d at the same time. You can use them in two ways: 1) Add v-flap on existing o utlet; 2) Use T-shaped plastic outlet, no add v-flap.”
o “Note: The product is provided with v-flap accessory. This accessory is not mandatory for installation, operation and use of the product.”

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required andthe installation is similar to the one show in section “INSTALLATION (VENTOUTSIDE)”.

Activated carbon filter can be used to trap odors.
In order to install the activated carbon filter, the grease filter should bedetached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction.Repeat the same on the other side.

NOTE:

Make sure the filter is securely locked. Otherwise, it would loosen andcause dangerous.
When activated carbon filter attached, the suction power will belowere

DESCRIPTION OF COMPONENTS

OPERATION

Wi-Fi Connection

Long press WiFi icon and enter into connecting mode: the backlit of WiFi icon keep flashing indicate the connection is under connecting, the backlit of WiFi icon is light on indicate it is
connected, same for standby mode; long press WiFi icon again and the connection will be stopped;

Speed plus button

For increasing the speed of the fan

Speed decrease button

For decreasing the speed of the fan.

Light button

Digital display

Fan speed display:”1″ for Low speed, “2” for Medium speed,
“3” for High speed, “4” for Booster function.

Quick timer:

Press & hold for 1 second, Digital display willflashing & into 5 minutes count down, after 5 minutes motor & lightwill turn off automatic & Buzzer sound for 1 second.

Booster function

This hood has a booster function. To activate the booster, Press to speed 4, enter into highest speed while the hood is in use
and it will increase speed for 5 minutes, before slowing down again.

Download hOn App

First of all, you should download hOn APP and install to your portable device. Then enroll your hood

ENROLLMENT CANDY HOOD

The image of the hood has the only purpose of presenting it. May not be perfectly representative

Press the WiFi button until the icon starts blinking When the pairing is completed the WiFi icon will be on.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.
The filter collects grease, smoke and dust….. so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year depending on how frequent the cooker hood used.

Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders andwiring from the hood. Important: It’s not possible to replace the bulbsindividually, it will be necessary to obtain the bulbs, bulb holders andwiring as a complete part. (LED light: MAX 1.5W)
Fit the replacement bulbs, bulb holders and wiring in the samemanners as the originals. Then reconnect the light wiring point.]

Refit the hood glass and fasten the glass screws. Make sure the screws arefully tightened.

TROBULESHOOTING

Fault	Cause	Solution
Light on, but fan does not work	The fan blade is jammed.	Switch off the unit

and repair by qualified service personnel only.
The motor is damaged.
Both light and

fan do not work

| Halogen light bulb burn.| Replace the bulb with correct rating.
Power cord looses.| Plug in to the power supply again.

Serious Vibration of the unit

| The fan blade is damaged.| Switch of the unit and repair by qualified service personnel only.
The fan motor is not fixed tightly.| Switch off the unit and repair by qualified service personnel only.
The unit is not hung properly on the bracket.| Take down the unit and check whether the bracket is in proper

location.

Suction performance not good| Too long distance between the unit and the cooking plane| ****

Readjust the distance to 65-75cm

Technology	Wi-Fi
Standard	802.11 b/g/n
Frequency Band(s)[MHz]	2400 MHz – 2483.5 MHz
Maximum Power[mW]	100 mW

Product information for networked equipment

power consumption of the product in networked standby if all wired

network ports are connected and all wireless network ports are activated:

| ****

2W

How to activate wireless network port:

| If the Hood has been enrolled with the APP, turn on the Hood to activate wireless network port.

How to deactivate wireless network port:

| If the Hood has been enrolled with the APP, turn off the Hood to deactivate wireless network port. If the Hood hasn’t been enrolled with the APP, wireless network port will be deactivated even the Hood is on.

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code and its serial number (a 16 character code which begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance. It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.