LAZZUR L-P5564-B5-14CH 5 Light 14 Inch Polished Chrome Pendant Instruction Manual
- June 8, 2024
- LAZZUR
Table of Contents
LAZZUR L-P5564-B5-14CH 5 Light 14 Inch Polished Chrome Pendant
SAFETY INFORMATION
Upon arrival of the product, inspect the wires for any cuts or abrasions that
could have occurred while in transit.
IF A DEFECT IN THE WIRE IS FOUND, DO NOT ATTEMPT INSTALLATION.
Please call our customer service team at
786-681-1919 or email us at
support@lazzur.com
Proper wiring is essential for safe operation of this fixture. Make sure to
not damage the electric wiring of the fixture or any other wiring/lines when
drilling. Check to make sure that no parts are missing prior to beginning
installation of the fixture. Use CSA/UL/ETL listed wire connectors suitable
for the gauge, type, and number of conductors.
We recommend installation of this lighting fixture be done by a licensed
electrician. If in doubt about electrical installation, consult a licensed
electrician. All electrical connections must be made in accordance with local
and National Electrical Code Standards (NEC) or Canadian Electrical Code
Standards (CEC). Contact your local municipal authority for more information
regarding code, inspections, and permits. L.A.ZZOR lighting fixtures are
intended to be installed utilizing compliant NEC/CECjunction boxes. Before
touching any wire, use a voltage tester to make sure it’s not live. Use non-
conductive tools when installing the fixture, such as insulated handles and
ladders made of wood or fiberglass. Turn off power source to the lighting
fixture prior to replacing bulbs. Give the bulbs adequate time to cool prior
to removing them.
TOOLS REQUIRED
{NOT INCLUDED}
PRIOR TO BEGINNING INSTALLATION
Ensure that all power supply has been disconnected, including turning off electricity at the circuit breaker, wall switch, or fuse box.
WARNING
Improper installation may cause electrical shock, fire, or equipment damage. The installer must be familiar with the construction and operation of the product as well as its associated hazards.
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY
90°C supply conductors minimum. Most houses built before l98S have supply
wires rated 60°C. Consult a qualified electrician prior to installation. Bulbs
are NOT included with the lighting fixture. Only use bulbs recommended for
your fixture. DO NOT EXCEED THE MAXIMUM WATTAGE.
ASSEMBLY INSTRUCTIONS
-
Insert the fastener (Part #1) into the ceiling.
-
Attach the mounting strip (Part #3) to the fastener (Part #1) by using the mounting screws (Part #5) and attach the mounting strip (Part #3) to the junction box (NOT INCLUDED) by using the screws (Part #2).
-
Adjust the wire length to the desired height. The height can be adjusted by pulling the wire through the canopy and securing it with the anti-pull buckle that is located inside of the canopy. Cut any excess electrical wire, but be sure to leave at least 6″-12″ minimum of electrical wire beyond the required length.
-
Connect the wires by using the wire connectors (Part #4). Make sure to use standard wire connectors when making connections.
-
Connect the black wire from the fixture to the black (HOT) wire from the junction box.
-
Connect the white wire from the fixture to the white (NEUTRAL) wire from the junction box.
-
To connect the grounding wire, there are two options. Each option depends on the electrical wiring in the home and the type of junction box being used. You can either:
-
Partially thread the green grounding screw onto the mounting bar, and then proceed to wrap the grounding wire from the fixture around the grounding screw. Tighten the green grounding screw. DO NOT OVERTIGHTEN. If necessary, wrap the remaining ground wire from the fixture with the grounding wire
from the supply with a wire connector. -
Connect the grounding wire from the supply to the fixture ground using a wire connector.
-
Make sure to wrap each connection with electrical tape for a more secure connection.
-
Please avoid having electrical wire exposed when wiring connections.
-
-
Mount the canopy (Part #6) to the mounting strip (Part #3) by using the cap nut (Part #7).
-
Insert the lightbulb (Part #13; NOT INCLUDED).
-
Attach the crystal (Part #12) to the lamp cup (Part #11) by using the screw (Part #10).
-
Attach the glass shade (Part #9) to the lamp base by using the socket grip (Part#8).
How to Identify the Fixture’s Wires
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>