AFTERGLOW 500-137-1 Wireless Deluxe Controller User Guide
- June 5, 2024
- AFTERGLOW
Table of Contents
500-137-1
Afterglow® Wireless Deluxe Controller
Quick Start Guide
Limited Warranty Information Inside
Initial Setup
Configuration initial ****
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 years.
First press A/B/X/Y or the Dpad to wake the controller. On the home screen,
select [Controllers] > [Change Grip/Order]. On the next screen, press and hold
the Sync button for at least 2 seconds. Once paired, the player indicator will
be illuminated.
Tip: To unpair hold down the sync button for at least 1 second
Charging the Controller
Connect the controller using the micro USB to the dock. The controller will
breathe red while being charged.
Tip: When the controller is low on battery the LEDs will turn off and
blink red every 30 seconds.
Program Back Buttons
| 
---|---
TIP
To disable the back button, double-tap the back button while holding down the
function button.
| 
---|---
Press any button you would like mapped and the function button LED will flash 3 times indicating a successfully mapped function.
Light Modes
To cycle through the light modes, hold down the function button and press
either L or R.
Mode 1 – The LEDs are on and set to your color.
Mode 2 – The LEDs fade in and out to set the color.
Mode 3 – The LEDs will cycle through all colors.
Mode 4 – The LEDs will react to the movement of the sticks.
Adjusting the Lights
To change the LED color, hold down the Function button and use the Left/Right
on the Dpad to change the color of the LEDs. Save the color setting by
releasing the Function button.
Tip: For a white color hold down the function button and click the left
stick.
To adjust the brightness, hold down the function button and click the ZR/ZL buttons to increase or decrease brightness. To return to 100% brightness, cycle through all brightness levels.
LIMITED WARRANTY
Coverage and Term
- PDP warrants that this product will be free from manufacturing defects for two years from the original date of purchase. Manufacturing defects are those defects in materials and/or workmanship, subject to final determination by PDP’s customer service department. This warranty applies only to original purchasers with valid proof of purchase from an authorized PDP retailer that clearly shows the date of purchase.
Exclusive Remedy and Exclusions
- The exclusive remedy for valid claims will be the repair, replacement, or refund of the product. This warranty does not cover defects caused by accidents, improper or abusive use of the product, unauthorized or improper modifications, repairs, or handling.
How to Get Service
- Purchasers should contact the PDP customer service department at 800-331-3844 (the US and Canada only) or + 442036957905 (the UK only) or by visiting support.pdp.com or support.pdp-eu.com. Inquiries are typically answered within twenty-four business hours.
Your Rights Under Applicable Law
- This warranty does not affect the legal rights of customers under applicable state, provincial or national laws governing the sale of consumer goods.
Additional Information for Australian Consumers
- PDP products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given to you under our express warranty is in addition to other rights and remedies you have under the Australian Consumer Law and other laws.
FCC AND IC STATEMENT FOR WIRELESS PRODUCTS
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment. The equipment
complies with FCC RF exposure limits set forth for an uncontrolled
environment. The equipment must not be co-located or operating in conjunction
with any other antenna or transmitter. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada, To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
FCC ID: X5B-5001371
IC: 8814A-5001371
CAN ICES-3 (B)/ NMB-3 (B)
WARNING – BATTERY LEAKAGE
This product contains a rechargeable lithium-ion battery pack. Leakage of
ingredients contained within the battery pack, or the combustion products of
the ingredients, can cause personal injury as well as damage to your product.
If battery leakage occurs, avoid contact with the skin. If contact occurs,
immediately wash thoroughly with soap and water. If liquid leaking from a
battery pack comes into contact with your eyes, immediately flush thoroughly
with water and see a doctor.
To avoid battery leakage:
Do not expose the battery to excessive physical shock, vibration, or liquids.
Do not disassemble, attempt to repair, or deform the battery.
Do not dispose of the battery pack in a fire.
Do not touch the terminals of the battery or cause a short between the
terminals with a metal object.
Do not peel or damage the battery label.
Need Help?
Visit support.pdp.com or talk to us at
800-331-3844 (USA and Canada only) or
+442036957905 (the UK only).
www.pdp.com
4225 W Buckeye Rd #2,
Phoenix, AZ 85009
www.pdp.com/patents
This product is manufactured and imported by Performance
Designed Products LLC.
© 2021 Performance Designed Products LLC. PDP, Afterglow, and their respective
logos are trademarks and/or registered trademarks of Performance Designed
Products LLC. All rights reserved.
@pdpgaming
Documents / Resources
|
AFTERGLOW 500-137-1 Wireless Deluxe
Controller
[pdf] User Guide
500-137-1 Wireless Deluxe Controller, 500-137-1, Wireless Deluxe Controller
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>