Knightsbridge VFRIC8ACW Valknight LED Downlight Instruction Manual
- June 16, 2024
- Knightsbridge
Table of Contents
Knightsbridge VFRIC8ACW Valknight LED Downlight
Product Information
Specifications
- Model: VFRIC8ACW / VFRIC8AWW
- Energy Efficiency Class: E
- Voltage: 230V
- Frequency: 50Hz
- Manufacturer: ML Accessories Ltd
- Authorized Representative: SLV Lighting Group
- Made in: China
Product Usage Instructions
Installation
Before starting the installation process, please read and understand all
the instructions provided below:
- Ensure that all power sources are turned off before attempting any installation.
- Make sure the area where the product will be installed is free from any obstructions or hazards such as joists, gas/water pipes, or electrical cables.
- Refer to Fig. 1 and Fig. 2 for visual guidance on the installation process.
Safety Precautions
Follow these safety precautions to avoid any accidents or damage:
- Disconnect the product from the circuit before conducting any high voltage or insulation resistance testing. Failure to do so may result in irreparable damage.
Maintenance
To ensure the longevity and proper functioning of the product, follow these
maintenance instructions:
- Regularly clean the product using a soft, lint-free cloth. Avoid using abrasive cleaners or solvents. Do not attempt to replace the LED light source yourself.
Contact a professional to replace the control gear if needed. Warranty
The product is supplied by ML Accessories Ltd in the UK and authorized by SLV Lighting Group in the EU. For warranty inquiries or claims, please contact the respective supplier:
- ML Accessories Ltd: Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT, UK. Website: www.mlaccessories.co.uk
- SLV Lighting Group Authorized Representative: Email: eprel@group.slv.com
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance. These instructions should
be used to aid installation of the following products:
VFRIC8ACW / VFRIC8AWW
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse, or circuit breaker
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- When used with the appropriate IC cage (VFRICC), any insulation should be laid unbroken over the luminaire (not packed around it). Only mineral wool-style insulation may be used
- When not used with the IC cage, allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
- This product is for indoor use only
- This product is Class II double insulated
- This product is IP65 rated (IP20 from above)
INSTALLATION
Note – If this product is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
-
Provide power to the required point of installation
-
Cut a suitable hole in the mounting surface as per the cutout details (see Fig. 1) ensuring not to infringe on any joists, gas/water pipes, or electrical cables
-
With the aid of a flat-head screwdriver remove the cover to access the mains terminal block (see Fig. 2)
- Connect the luminaire to the mains supply ensuring the correct polarity is observed:
- L – Live (brown),
- N – Neutral (blue). The earth terminal is nonfunctional and only provided for convenience. Two cables can be inserted into the push-fit terminal block in order to achieve looping/loop-out wiring
- Refit the terminal cover ensuring the sheath of the mains cable is secured by the cable clamp
- Connect the driver via the plug and socket to the luminaire
- Fit a bezel onto the luminaire by twisting it into place
- Lift both spring clips on the sides of the fitting and push into the ceiling ensuring the driver is not resting against the luminaire
- Switch on and check for the correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high
voltage or insulation resistance testing. Irreparable damage will occur if
this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095. This product contains a non-replaceable LED light source and a control gear that can be replaced by a professional.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents that may damage the product. This product is dimmable using leading- edge or trailing-edge dimmers, please check compatibility before installation. The external cable of this luminaire cannot be replaced; if the cable is damaged, the luminaire should be destroyed. This product should be dismantled for disposal when it reaches the end of its life. Please see the website for dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 5 years from the date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserves the right to alter product specifications without prior notice.
SUPPLIED BY
(UK) MANUFACTURER ML ACCESSORIES LTD, UNIT E CHILTERN PARK, BOSCOMBE ROAD,
DUNSTABLE LU5 4LT, WWW.MLACCESSORIES.CO.UK (EU)
AUTHORISED REPRESENTATIVE SLV LIGHTING GROUP, DAIMLERSTRASSE 21-23, 52531
ÜBACH-PALENBERG, GERMANY EMAIL: EPREL@GROUP.SLV.COM
MADE IN CHINA
FAQs
Can I install the product myself?
Yes, you can install the product yourself by following the provided installation instructions. However, it is recommended to seek professional assistance for electrical connections.
Can I replace the LED light source?
No, the LED light source is non-replaceable. Contact a professional if the control gear needs replacement.
Where is the product manufactured?
The product is manufactured in China.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>