Knightsbridge BT9ACTS 230V IP65 9W CCT Adjustable LED Bulkhead with Sensor Instruction Manual
- June 3, 2024
- Knightsbridge
Table of Contents
INSTALLATION & MAINTENANCE MANUAL
BTxxACTS
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance.
These instructions should be used to aid installation of the following
products: BT9ACTS / BT14ACTS / BT20ACTS
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
- This product is Class II double insulated
- This product is IP65 rated
INSTALLATION
Note – Microwave sensors may not be suitable for all installations. for example enclosed spaces. as they are able to detect movement through non- metallic surfaces like plasterboard and thin doors.
-
Provide power to the required point of installation. Suitable IP rated junction boxes should be used where required
-
Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)
-
Remove the fastening screw securing the LED plate and open the LED plate (see Fig. 2)
-
Mark the location of the fixing holes. and drill the holes ensuring not to infringe with any gas/water pipes or electrical cables
-
Feed the cable via the rubber grommet to retain IP rating. and secure the baseplate to the surface
-
Connect the Live (brown) and Neutral (blue) to the terminals on the terminal block (see Fig. 3)
-
The additional terminal called Slave Live (14 is available to enable the sensor to power on additional luminaires. A max. LED load of 400W can be controlled by the sensor
-
Please see DIP Switch Layout to set up sensor
-
Refasten the LED plate screw
-
Choose the required colour temperature by means of the DIP switch (see Fig. 4)
- Reattach the diffuser by rotating clockwise
- Switch on and check for correct operation
SENSOR LAYOUT
DIP SWITCH LAYOUT
DIP SWITCH SETTINGS
Detection area
Hold time
This is the time period the lamp remains at 100% after no motion is detected
Daylight sensor
When set to Disable, the daylight sensor will switch the lamp on when motion is detected regardless of the ambient light level
WARNING
This product must be disconnected from the circuit if subjected to any high
voltage or insulation resistance testing. Irreparable damage will occur if
this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class D (BT9ACTS) / E (BT14ACTS, BT20ACTS) to Regulation (EU) No. 2019/2015. This product contains an LED light source which can be replaced by the end user and a control gear which can be replaced by a professional.
Clean with a soft dry cloth only, do not use aggressive cleaning products or
solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this
luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its
life. Please see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end
of its life.
Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to
install this product in accordance with the current edition of the IEE Wiring
Regulations, improper use, or removal of the batch codes will invalidate the
warranty. If this product should fail within its warranty period, it should be
returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any
installation costs associated with the replacement product. Your statutory
rights are not affected. ML Accessories reserve the right to alter product
specification without prior notice.
Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with CE marking
ML Accessories Ltd. Declare that all products have been designed,
manufactured, and tested in accordance with the requirements of the relevant
legislation
CE marking legislation
In Accordance with the following Directives:
2014/35/EU
2014/30/EU
2014/53/EU| Low Voltage Directive
EMC Directive
Radio Equipment Directive
---|---
Including Legislation
1907/2006
2015/863
2021/341| REACH
RoHS
ERP
---|---
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The product
complies with all essential requirements of the directives.
Scott Brewer
Technical Manager
Catherine Connolly
CEO
**** ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable.
Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are
introduced without ML Accessories Ltd. written consent.
Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with UKCA marking
ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation
UKCA marking legislation
UK SI 2016 No. 1091
UK SI 2016 No. 1101
UK SI 2012 No. 3032
UK SI 2017 No. 1206
UK SI 2021 No. 1095| Electro Magnetic Compatibility Regulations 2016
The Electrical Equipment (Safety) Regulations 2016
Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
Radio Equipment regulations 2017
The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021
---|---
Included Legislation
UK SI 2008 No. 2852
UK SI 2013 No. 3113| UK REACH
WEEE
---|---
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The
products comply with all essential requirements of the directives.
Scott Brewer
Head of Technical
Catherine Connolly
CEO
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable.
Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are
introduced without ML Accessories Ltd. written consent.
ML Accessories Limited LU5
4LT
www.mlaccessories.co.uk
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern
Park, Boscombe Road, Dunstable
LU5 4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasse-ler Lohweg 18,
40547 Düsseldorf, Germany,
Email: eprel@nnuks.com
DCJUL22_V3
Documents / Resources
|
Knightsbridge BT9ACTS 230V IP65 9W CCT Adjustable LED Bulkhead with
Sensor
[pdf] Instruction Manual
BT9ACTS, BT14ACTS, BT20ACTS, BT9ACTS 230V IP65 9W CCT Adjustable LED Bulkhead
with Sensor, 230V IP65 9W CCT Adjustable LED Bulkhead with Sensor, 230V IP65
9W CCT Adjustable LED Bulkhead, IP65 9W CCT Adjustable LED Bulkhead, 9W CCT
Adjustable LED Bulkhead, CCT Adjustable LED Bulkhead, Adjustable LED Bulkhead,
LED Bulkhead, Bulkhead
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>