Knightsbridge CABBCCW Brushed Chrome 230V LED Under Cabinet Light Instruction Manual
- October 30, 2023
- Knightsbridge
Table of Contents
rushed Chrome 230V LED Under Cabinet Light
Instruction Manual
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance.
These instructions should be used to aid installation of the following
products: CABBCCW / CABBCWW / CABCCW / CABCWW / CABWCW / CABWWW
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- When installing recessed, allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
- This product is for indoor use only
- This product is Class I and must be earthed
- This product is IP20 rated
INSTALLATION
Note – If this product is being used in conjunction with an external PIR or
sensor, please confirm with the manufacturer of the sensors that they are
compatible with LED luminaires.
-
Provide power to the required point of installation
-
To recess mount, cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuringnot to infringe with any joists, gas / water pipes or electrical cables.
-
To surface mount, fix the outer housing to a suitable solid surface ensuring not to infringe with any gas / water pipes or electrical cables
-
Connect the luminaire to the mains supply using a suitable junction box (not included), ensuring the correct polarity is observed: L – Live (brown), E – Earth (green/yellow), N – Neutral (blue)
-
Push the fitting securely into the cut-out or housing
-
Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high
voltage or insulation resistance testing. Irreparable damage will occur if
this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class F to
Regulation (EU) No. 2019/2015 and (UK)2021 No. 1095.
This product contains an LED light source and control gear which can be
replaced by a professional.
Clean with a soft dry cloth only, do not use aggressive cleaning products or
solvents which may damage theproduct.
This product is non-dimmable.
The external supply cable of this luminaire cannot be replaced; if the cable
is damaged, the luminaire should be destroyed.
This product should be dismantled for disposal when it reaches the end of its
life. Please see website fordismantling instructions.
This product should be recycled in the correct manner when it reaches the end
of its life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to
install this product in accordance with the current edition of the IEE Wiring
Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty
period, it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any
installation\ costs associated with the replacement product. Your statutory
rights are not affected. ML Accessories reserve the right to alter product
specification without prior notice.
SUPPLIED BY:
(UK) MANUFACTURER ML ACCESSORIES LTD,
UNIT E CHILTERN PARK, BOSCOMBE ROAD,
DUNSTABLE LU5 4LT,
WWW.MLACCESSORIES.CO.UK
(EU) AUTHORISED REPRESENTATIVE
NNUKS HOLDING GMBH,
NIEDERKASSELER LOHWEG 18,
40547 DÜSSELDORF, GERMANY,
EMAIL: EPREL@NNUKS.COM
MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>