Stiive ID130PlusHR Fitness Tracker with Heart Rate Monitor User Manual
- May 15, 2024
- Stiive
Table of Contents
ID130PlusHR Fitness Tracker with Heart Rate Monitor
User Manual
ID130PlusHR Fitness Tracker with Heart Rate Monitor
Thanks for purchasing this product.
Please read th is Manual carefully before use.
Use introduction
Product overview
Touch Instructions
- Click to toggle function.
- Long press to enter the sub interface.
- Short press to turn on the screen when the screen is off.
- Long press for 3 seconds to turn on.
Charging instructions
As shown in the picture, remove one side of the strap and plug the end with
the USB interface into the USB port of the power supply to charge; charge for
5 minutes or press and hold the touch point for 3 seconds to activate the
device. 
APP download and connection
APP download
Please download and install the “Runmefit” application in AppStore, GooglePlay
or scan the QR code on the right to download.
https://www.runmefit.cn/client/download
Pairing
Please turn on the Bluetooth of the mobile phone before pairing, and then you
must perform the Bluetooth pairing in the APP, and the Bluetooth pairing
cannot be performed in the mobile phone system.
There are one ways to pair:
- Click “Add Device” on the “Devices” interface of the APP, and the luetooth search interface will pop up. Next, find the corresponding Bluetooth name to pairing.
Function introduction
This device has rich functions, mainly including the following:
- Health functions: heart rate detection, blood oxygen saturation, blood pressure detection, temperature detection, sleep monitoring, stress monitoring, drinking water reminder, sedentary reminder, etc.;
- Sports functions: 16 sports modes, sports data recording, etc.;
- Others: message reminder, stopwatch, alarm clock reminder, phone call reminder, etc.
Precautions
- The waterproof level of this product is IP68, and can only use it for daily waterproof protecton, such as washing hands, raining, Elc.;
- Do not take it for swrnrning, diving, surfing, and other water sports;
- Do not use it in high-temperature places such as saunas and steam rooms. The high-temperature environment will significantly increase the probability of water entering the watch;
- This product is not a medical device. Therefore, all the measured data and results are for reference only and not for medical evidence.
FAQ
1. Can not search the Bluetooth of the device in the APP.
It is possible that when you connected the device, you linked directly to the Bluetooth of the mobile phone system. Therefore, the connected device needs to be connected to the APP and not join in the phone settings. If the Bluetooth has bound in the phone settings, please unbind in the phone settings first, and then enter the APP to search for Bluetooth to bound. Note: A Bluetooth pairing request will pop up when the watch has connected to the IOS system. You need to click Allow pairing to connect the device normally.
2. The APP can't synchronize the data of the smartwatch.
The Bluetooth wireless connection may have signal interference and other reasons, which may cause the link or data synchronization time to be too long. In addition, the Bluetooth of some mobile phones may occasionally be abnormal when starting up. Therefore, it is better to restart the phone's Bluetooth before pairing.
3. The watch cannot be charged.
Please make sure that the positive and negative poles of the charging port are not reversed and that the charger is powered on; when the battery of the watch is too low, there will be a period of battery pre-charging time.
4. The time of the watch is not accurate.
When the device is fully charged after a dead battery or has not been used For a long Lime, Lhere may be errors in the time. However, as long as Lhe APP is connected, the time will be automatically synchronized.
5. Heart rate detection will fail or be inaccurate.
These conditions may be caused by non-standard wearing methods, such as light leakage due to incomplete fit to the skin, movement of the watch on the skin, wearing the watch too tightly, raising the arm, and making a fist that affects the blood circulation, Etc. These conditions may affect the heart rate measurement. The correct measurement method requires laying your arms flat, relaxing your body, and keeping it still while ensuring that the watch is close to your wrist.
6. The number of steps recorded by the watch is inaccurate or wrong.
The following conditions may cause it: • The arm swing amplitude, frequency, and law of the arm swing will have a particular impact on the step count. In addition, the accuracy of the vvatch's step count is related to the walking posture, walking habits, walking speed, walking continuity, and road conditions. • Please fill in various information correctly in the APP and synchronize it to the watch, including gender, height, weight, age, all of which will affect the step counting algorithm. • In daily life, we often shake our arms or bodies. In some scenes, the shaking is regular, and the watch will misjudge it as walking. • If only a few steps are taken when counting steps and the movement is not continuous, the watch may not record. • The watch does not have a GPS positioning function, so there will be a specific error in step counting in sports mode.
For more questions (for example, no message reminder), please check “My”-” FAQ” in the APP.
| Model ID130PlusHR
---|---
| Battery Capacity lOSmAh
| Charging Time about 1.5 hours
| Waterproof Level IP68
| Screen Type 0.96″ -inch color screen
| ChargingVoltage 5v
| Battery Life 15 days
| Bluetooth Version BLES.O
https://www.runmefit.cn/client/watchs/content/version/S5/lang/1
Scan the QR code for
more function information
Made in China