Stiive ID115Plus HR Fitness Tracker with Heart Rate Monitor User Manual

June 9, 2024
Stiive

Stiive ID115Plus HR Fitness Tracker with Heart Rate Monitor

ID115Plus HR Fitness Tracker with Heart Rate Monitor

Introduction

Thank you for purchasing our products. This manual addresses the safety guidelines, warranty, and operating instructions. Please review this manual thoroughly before operating your device.

Getting Started

What’s in the box
  • Fitness tracker (ID115Plus HR with bands)

  • Quick start guide

Note:
This tracker is designed with a built-in USB plug. No charging cable is required for charging, and no charging cable or wall charger is included in the package

What’s in this Document

This manual gets you started quickly with setting up your tracker. Setup ensures  that your tracker can synchronize its data with the VeryFitPro app, where you can get detailed information on your stats, view historical trends, log sleep, and more. As soon as setup is complete, you’re ready to start moving. The remainder of the manual walks you through every function on your ID115Plus HR.

Setting up Your Tracker

This fitness tracker does not need a charging cable, it has a built-in charger in its body and you can charge it directly with its main body.

Please charge your tracker for at least 10 minutes to have it activated before initial use.

Step 1: Gently remove the strap on both sides of the device.

Step 2: Find the metal pins on the device.

Step 3: Plug into the USB port, make sure the metal pins of the device are connected to the metal pins of the USB port.

Step 4: The red light will come on during charging and off auto once fully charged. If Not, please check and change the metal pins to the opposite direction, or try other sockets.
Setting up Your Tracker

Assembling / Disassembling your tracker

Assembly
Insert the bands in the direction of the arrow
Setting up Your Tracker

Disassembly
Gently pull the bands off the tracker body in the direction of the arrow
Setting up Your Tracker

Wearing Your Tracker

All-day wear and exercise

For all-day wear when you’re not exercising, wear the device on your wrist horizontally, a Finger’s width below your wrist bone and lying flat, the same way you would put on a watch.
Wearing Your Tracker

For optimized heart rate tracking, keep these tips in mind:

  1. Experiment with wearing the tracker higher on your wrist during exercise.
    Because the blood flow in your arm increases the farther up you go, moving the tracker up a couple of inches can improve the heart rate signal. Also, many exercises such as bike riding or weight lifting require you to bend your wrist frequently, which is more likely to interfere with the heartrate signal if the tracker is lower on your wrist.
    Wearing Your Tracker

  2. Do not wear your tracker too tight. A tight band restricts blood flow, potentially affecting the heart rate signal. This being said, the tracker should also be slightly tighter (snug but not constricting) during exercise than during all-day wear.

Using Your Tracker

App Installation

Use the tracker with our customized VeryFitPro app. You can download VeryFitPro from App Store/Google Play or scan the QR codes below to download.

QR-codeiOS

| VeryFitPro|

QR-codeAndroid

---|---|---

Notes:
The VeryFitPro app is only compatible with smartphones, not tablets or
PCs. Smartphone operating system should be iOS 7.1 / Android 4.4 or higher;
Bluetooth version should be 4.0 or higher

Smart Phone System Requirements

iOS 7.1 or higher
Android 4.4 or higher
Bluetooth 4.0 or higher

App Interfaces

Using Your Tracker

Pairing the Tracker with Your Phone

  1. Please ensure your phone’s Bluetooth is enabled before beginning the pairing process.
  2. Open the VeryFitPro app on your smartphone and go to the “Device” page, tap “Pair device”, then your smartphone starts searching devices.
  3. In the list of found devices that appear on your phone, tap “ID115PlusHR” to connect the tracker to your smartphone. (If your phone failed to find ID115Plus HR, please tap the touch key to wake the tracker and search the tracker on your phone again.)
    Pairing the Tracker with Your Phone

Notes:
Once the tracker is connected to your app, the tracker will automatically search and reconnect itself if the connection is lost or when Bluetooth is restarted after manual disconnection.

If the tracker is unbound from the app, the information on the tracker will be reset, and the information on the app will be cleared. Please don’t unbind the connection unless there is an issue that will require a reset.

The tracker can only pair with one Bluetooth device at a time. When pairing, please ensure there are no other Bluetooth devices nearby.

To reconnect the tracker to your smartphone, please kindly take the following steps:

  1. Go to your smartphone system Settings, find the VeryFitPro app and enable the Location and all Notifications.
  2. Clear all running/background processes on your smartphone. Go to the VeryFitPro app and swipe down “Main page”, then the tracker will reconnect to your smartphone and update data. You can also restart your smartphone and Bluetooth, then rebind the tracker in the app.

Warranty

We strive to build our products with the highest attention to detail and craftsmanship. However, sometimes there are occurrences of a defect, so we are happy to offer a ONE-year hassle-free warranty on all our devices as we continue to make amazing products. Please contact us if you have any questions about our devices.

Important Safety Instructions

The device contains electrical equipment that may cause injury if not used properly. For example, prolonged contact may contribute to skin allergies for some users. To reduce irritation, please read the safety guidelines on the following pages to ensure proper use and care.

Do not expose your device to liquid, moisture, humidity or rain while charging; do not charge your device when it is wet, as this may result IN electrical shock and injury.
Keep your device clean and dry. Do not use abrasive cleaners to clean your device.
Consult your doctor before use if you have any preexisting conditions that
might be affected by using this device.

Do not wear it too tight. If your device feels hot or warm, or if it causes any skin

FAQs

Failure to find the tracker when Pairing

  1. Make sure your smartphone’s Bluetooth is enabled and your smartphone’s system meets the requirements of Android 4.4 or higher, iOS 7.1 or higher, and Bluetooth 4.0 or higher.
  2. Make sure the distance between your smartphone and the tracker does not exceed 0.5 meters and that Bluetooth communication is also within range (10 meters max).
  3. Make sure your tracker has enough battery life. If there is still a problem after being fully charged, please contact us.

Occasional failure to connect with Bluetooth

Reboot your smartphone or restart your smartphone’s Bluetooth.

Failure to charge the tracker

Make sure the direction of the tracker’s USB plug is correct when plugging into a USB port for charging (Ensure the metal strips of the tracker’s USB plug align with the USB strips).
If it is charged correctly, the tracker’s red indicator turns on and will be off when it has been fully charged.
As the built-in battery capacity is small, please remove the tracker from the power supply once fully charged. Prolonged charging may shorten battery life.

Failure to receive SMS/calls notifications

Calls/SMS notification function works when the tracker connects to your smartphone via the app. Please kindly r efer to the following tips:
Go to your smartphone Settings, find VeryFitPro app and enable the
Location and all Notifications.
Enable your phone’s Bluetooth and go to the VeryFitPro app to bind the tracker.
Enable the Call/SNS Alert function, and tap “v” to save your settings.

Failure to count steps accurately

The fitness tracker has a built-in 3D sensor. It records your steps when you swing your arms. Sometimes the data displayed on the tracker will be slightly delayed, and the data will automatically reset if you walk less than 40 steps continuously.
To test the accuracy of the pedometer, please walk casually and continuously at least 100 steps.

Failure to measure heart rate

Make sure the tracker sits neatly on your wrist before use. Tap the touch key to enter heart rate mode and wai1t 10-20s to obtain your heart rate.

Failure to connect to smart hone

The tracker will disconnect from your smartphone in the following cases:
Smartphone Bluetooth is off or exceeds the Bluetooth connection range (the l5maximum Bluetooth connection range is 10 meters and can easily be reduced by walls, furniture, etc.)
The VeryFitPro app is closed on the phone. (This can occur automatically under certain circumstances.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals