CREALITY Falcon2 40W Laser Engraver and Cutter User Guide

CREALITY Falcon2 40W Laser Engraver and Cutter

Dear Users,
Thank you for choosing Creality. For your convenience, please read this quick guide carefully before use, and follow the instructions in the quick guide.

Creality team is always here to provide you with quality services. If you encounter problems during use, please contact us via the phone number or email address provided at the end of the Quick Guide. Besides,
video instructions are available on the TF card for your reference. You can also visit Creality’s official website (www.cxsw3d.com) to learn more about software and hardware, contact, operation, maintenance, etc.

Motherboard Firmware

When the machine is powered off, insert the TF card into the card slot, and it will automatically update the firmware when it is powered on. The buzzer will keep beeping during the update process, and the update will be completed when the beep ends (please keep the power on till completion).

Laser Module Firmware
When the machine is powered off, insert the TF card into the card reader, then insert it into the USB-C port on the top of the laser module through the USB-A to USB-C adapter, and the firmware will automatically update when it is powered on. During the update process, the indicator of the laser module will turn orange with a marquee effect, and the update will be completed when it stops the marquee effect (please keep the power on till completion).

Security Statement

When a laser engraver engraves or cuts materials, it casts a high-density laser beam that heats the surface to vaporize materials without burning them. But most materials are inherently flammable and can be ignited, which may
burn the machine and the surroundings.

Please use it as instructed below:

1. Do not place this product near flammable and explosive materials, volatile solvents or heat sources. Please place this product in a ventilated, cool and dust-free environment.
2. Do not use other power cords than the one provided in the package during the installation.
3. Regularly clean the body and laser module with an anti-static brush and a dry cloth when the machine is powered off.
4. Please connect the silicone tube on the laser module matter using an air assist or not. Otherwise, there will be a risk of lens contamination.
5. The working temperature of the laser module is 5°C-35°C. Avoid using this product in a humid environment, and do not use it in thunderstorm weather.
6. If the product isn’t used for a long time, please turn off the product and disconnect the power cord.
7. When the product is connected to the power supply, please do not touch the electronic areas with your hands or other tools. It is forbidden to plug and unplug the laser module cable when the machine is powered on.
8. When the product is running, please do not touch any part of the moving system and laser module.
9. Please place a flat object that the laser cannot penetrate under the processed material, such as an aluminium alloy or stainless steel plate.
10. During the laser engraving, please wear goggles to avoid vision damage caused by looking directly at the laser spot.
11. Smoke or smell may be produced during laser engraving and cutting. It is recommended to operate in a well-ventilated environment.
12. Children under the age of 10 are strictly prohibited from using this product without adult supervision to avoid injury.
13. Prepare fire extinguishers for backup. Regularly maintain and inspect the fire extinguishers.
14. It is forbidden to leave it unattended while the machine is working.
15. Users should abide by the laws and regulations of the corresponding country and region where the equipment is located (where it is used), practise professional ethics, and pay attention to safety obligations. It is strictly forbidden to use our products or equipment for any illegal purposes. If there is any violation, we will not be responsible for the relevant legal responsibilities.

Parameters

• Product Name Creality Falcon2
• Product Size 622567185mm
• Net Weight 6.8kg
• Input Voltage 100-240V~ 50-60Hz
• Output Voltage DC 24.0V 5.0A
• Operating Temperature 5°C-35°C
• Safety Certifications IEC60825,FDA,CE,ROHS,FCG_UKCA, UL Report,PSE
• Engraving Area 400mm*415mm
• Laser Source Diode Laser
• Laser Wavelength 455±5nm
• Optical Power 22W
• Laser Class Class IV (FDA)
• Laser Engraving Software LightBum, LaserGRBL
• Operating System Windows/MacOS
• Supported File Formats Jpeg, jpg, png, bmp, svg, dxf, etc.
• Supported Materials Cardboard, wood, bamboo, rubber, leather, fabric, acrylic, plastic, etc.

Product Overview

1. Lett Y-axis Component
2. Right Y-axis Component
3. Front X-axis Component
4. Rear X-axis Component
5. Adapter Board
6. Laser Module (22W)
7. Raiser Stand
8. Control Panel
9. Emergency Stop Button
10. Security Lock
11. TF Card Slot
12. Type-C Port
13. Power Input
14. Power Button

Parts List

1. Machine Frame*1
2. Raiser Stand (including pads) *4
3. Raiser Stand (without pad)*4
4. Laser Module*l
5. Air Pump*1
6. USB-C Cable*1
7. Multi-level Fixed Focus Block'<1
8. Goggles*l
9. Basswood Board*3
10. Anti-static Brush *1
11. Storage Box *1
12. Power Supply*1
13. M 1.5/M2/M2.5/M3 Allen Wrench*1
14. Open-end Wrench*1
15. TF Card & Card Reader *1
16. USB-A to USB-C Adapter *1
17. Key*1
18. Protective Lens*1
19. M3X1 O / M4X6 Hexagon Socket Head Screw*4
20. Dust-free Cloth*l
21. Black Cable Straps*3
22. Metal Protection Plate*1

Assemble Directions

1. Install four raiser stands (including pads): There are 3 positions for installation at each of the four corners of the machine, to suit different sizes of workbenches. Pay attention to symmetry when installing the stands.
   Note: The other four raiser stands (without pads) can be used to raise the machine. You can stack them if necessary.

2. Connect the machine with the air pump

3. Unplug the rubber plug in the air nozzle of the air pump, and connect the silicone tube from the machine to the air nozzle of the air pump.

4. Plug the air pump cable into the air pump interface on the left side of the machine, and you can adjust the airflow through the knob switch.

5. Install the laser module: Install it onto the bracket and lock it with the thumb screw on the right.

6. Connect the laser module with the adapter board, and fix the laser module cable and the silicone tube with the cable management clips.

7. Organize the laser module cable and silicone tube with the cable straps.

Preparation

Before starting work, you need to complete the following preparations:

1. Carefully read the content in the security statement again.
2. Stack the protective metal plate, honeycomb worktable (optional) and processed materials in sequence.
3. Adjust the focal length of the laser module with the multi-level fixed focus block.
   Place the multi-level fixed-focus block between the module and the processed material, lower the laser module until the bottom of the laser module cover touch on the corresponding tier marked on the multi-level fixed-focus block, and then lock it with the thumb screw on the right side. For example, when you’re engraving or cutting 2mm thick basswood boards or other materials.

Software Installation & Use

The machine can be controlled with LaserGRBL or LightBurn after being connected to a PC via a USB-C cable, and can also work by reading codes (exported from Llghtburn) in a TF card. For software tutorials, please refer to the information provided in the TF card.

Control from PC

Connect the machine to a PC via a USB-C cable. If your computer does not have a USB-A port, please use the included adapter to convert it. While controlling from PC, you can also control it through the Start/Pause button on the control panel of the machine.

Work with TF Card

1. Generate the engraving file (geode) through the LightBum software, and save the file to the root directory of the TF card (the machine will access the file with the latest data in the root directory of the TF card by default, so it is advised to delete other irrelevant flies in the first directory). Insert the TF card into the machine before powering it on, plug in the power adapter and power cord, and turn on the power button.

   • After the machine is powered on, it will sound two beeps and enter standby mode. The indicator light will pulse green slowly.
   • Press the Frame button, and the machine will exit the standby mode and enter the preview mode. The laser module will emit a weak beam and move along the X/Y axis to frame the target working area. The indicator will be in solid blue. You can adjust the material to a suitable position, or make fine adjustments through the arrow buttons on the control panel.

2. In the preview mode, press the Start/Pause button to enter the engraving mode, the laser module will emit a strong beam, and the machine will start engraving. The indicator will be in solid blue. If you need to pause the engraving, please press the Start/Pause button, and the indicator light will pulse green slowly. Press the Start/Pause button again to
   continue engraving.
   If you need to cancel the engraving, please press and hold the Start/Pause button for 3 seconds, the machine will sound a beep, and the machine will reset. After the reset is completed, the machine will sound two beeps and enter the standby mode. The indicator will pulse green slowly.

3. After the engraving is completed, the machine will sound three beeps and then reset. After the reset is completed, the machine will sound a beep and enter the standby mode, and the indicator will pulse green slowly.

Indicator Explanations

Control Panel

1. The indicator is off: The machine is in a power-off state, or some abnormality occurs.
2. Solid white: The machine is in the initialization mode, and it will automatically enter the standby mode after the initialization is completed.
3. Flashing purple: The machine is in the firmware upgrade mode, and the buzzer makes a rapid sound at the same time. It will automatically enter the standby mode after the upgrade is completed.
4. Flashing red: The machine is in abnormal mode, and the buzzer makes a rapid sound at the same time. It will automatically enter standby mode after dealing with the abnormality.
5. Pulsing green (slowly): The machine is in standby mode, and you can press the Frame button to enter preview mode.
6. Solid blue: The machine is in preview mode or engraving mode, and the laser module is emitting a beam. Special attention should be paid to safety.
7. Flashing yellow: There is no geode file in the root directory of the TF card, and the buzzer will sound two beeps.
   • AIR: Detects the current airflow passing through the laser module.
   • Flashing red: No airflow. Smoke and dust may contaminate the lens during engraving or cutting, please check the working status of the air pump and ensure that the silicone tube is connected.
   • Solid orange: Small airflow volume. It is recommended to enable a small airflow volume when engraving since a large airflow volume can affect the engraving result.
   • Solid green: Large airflow volume. The airflow volume can be adjusted according to individual needs when cutting.
   • FIRE: Detects whether the processed material is burning.
   • Red: Flame is detected. It is recommended to stop the current work immediately to ensure safety.
   • Orange: There is a fire hazard. Please confirm the material and set the working parameters properly.
   • Green: No flame is detected. Please clean and maintain the laser module regularly.
   • LENS: Detects whether the lens of the laser module is dirty.
   • Red: The lens is seriously dirty. Please stop the current work immediately, and clean and maintain the laser module.
   • Orange: The lens is slightly dirty. It is recommended to stop the current work as soon as possible and clean and maintain the laser module.
   • Green: The lens is not dirty. Please clean and maintain the laser module regularly.

Notes

1. The FIRE and LENS alarm functions are enabled by default. The AIR alarm is disabled by default, but the indicator will indicate the status of the laser module properly. To enable the alarm, please refer to the “Laser Module Alarm Function.pdf” in the included documents.
2. When alarming, please check the laser module carefully, and then press the Reset button on the laser module to stop the alarm.
3. The USB-C port on the laser module can be used to upgrade the firmware of the laser module or export the work log of the laser module. When the port is not in use, please plug in the dust-proof plug.

Work with TF Card

Control from PC

WARRANTY

Before returning the product and filling in a warranty, please contact an after-sale person to go through the after-sale formality. Attach this warranty card along with the returned machine.

Note: The client needs to fill in a basic form. and return reasons. Repair records should be retained for technicians.

• Users should abide by the laws and regulations of the country and region where the equipment is located (place of use), abide by professional ethics, and pay attention to safety obligations. It is strictly forbidden to use our products or equipment for any illegal purpose. Our company is not responsible for the relevant legal responsibilities that the violator should bear.
• Since each model is different, the actual product may be different from the picture. Please refer to the actual product. The final interpretation right belongs to Shenzhen Chuangxiang 3D Technology Co., Ltd.

3D Printing Industry Evangelist
With the spirit of evangelists, we want to share the convenience of technology with everyone.

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.

• Add: 18F, JinXiuHongDu Building, Meilong Bivd., Longhua Dist., Shenzhen, China 518131
• Official Website: www.creality.com
• Tel: +86 755-8523 4565
• E-mail:
  • info@creality.com
  • cs@creality.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>