geemarc LoopHEARTM10 Amplified Hearing Assistant Instruction Manual
- June 16, 2024
- geemarc
Table of Contents
- geemarc LoopHEARTM10 Amplified Hearing Assistant
- Product Description
- Product Usage Instructions
- INTRODUCTION
- DESCRIPTION
- INSTALLATION
- USING THE LH10
- TROUBLESHOOTING
- SAFETY INFORMATION
- GUARANTEE
- FCC STATEMENT
- RECYCLING DIRECTIVES
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
geemarc LoopHEARTM10 Amplified Hearing Assistant
Product Description
The LoopHEARTM10 is an amplified hearing assistant designed to enhance sound for individuals with hearing impairments. It features an internal microphone, a mode switch for selecting microphone or T coil mode, and a rechargeable battery for convenience.
Specifications
- Product Name: Amplified hearing assistant Portable amplifier
- Manufacturer: Geemarc Telecom
- Model: LoopHEARTM10
- Power Source: 3.7V Li-po Rechargeable Battery
- Charging Port: USB Type C (5.0V DC)
- Microphone: Internal microphone
- Switch mode: MIC or T
- Headset Port: Compatible with supplied headset
- Volume Control: On/Off Volume control wheel
- LED Indicator: On/Off LED
Product Usage Instructions
Unpacking and Contents
When unpacking the LoopHEARTM10, you should find the following items in the
box:
- LoopHEARTM10 Conversation Piece
- Headset with rubber ear cushions
- 3.7V Li-po Rechargeable Battery
- USB type C / USB A cable for charging
- Lanyard (optional)
- A microphone with holder and 3m lead (optional)
- A belt clip
- 1 User Guide
Setting Up
- Open the battery compartment located on the rear of the LH10 Conversation Piece.
- Connect the supplied rechargeable battery (3.7V) into the battery compartment.
Turning the LoopHEARTM10 On and Off
- Switch the headset on.
- Ensure the mode switch is set to (MIC).
- Roll the On/Off Volume control wheel upwards. The (On) LED will display Green.
- Adjust the Volume to a comfortable level by rolling the On/Off Volume control wheel.
To turn the LH10 off, roll the On/Off Volume control wheel downwards. The Green LED will switch off and OFF will be shown on the On/Off Volume control wheel.
Using T Coil Mode
The LH10 can be used in rooms especially equipped with a magnetic loop
(conference, etc.) due to its built-in T coil. To use T coil mode:
- Set the mode switch to T.
- The LH10 will receive the emitted magnetic waves and amplify them to your headset, providing all the benefits of the built-in T coil.
Using an External Microphone
An external microphone (optional) can be connected to the Mic socket. In this
case, the built-in T coil is disabled.
Tone and Balance Setting
The tone and balance can be adjusted by using the controls found within the
battery compartment.
Troubleshooting
The ‘On’ LED is Red
Possible causes:
- The battery pack is not charged. Charge the battery if the battery pack is used.
- If standard AAA batteries are installed, replace them with new batteries.
The LH10 appears not to be working
Try the following:
- Make sure that the headset is securely plugged in.
- Ensure that the volume is correctly adjusted.
- Make sure that the battery is fully charged or use good batteries.
- If using a headset/earpiece, make sure the mode switch is set to MIC. If using an induction loop, set it to T.
The LH10 is not charging
Check the following:
- Ensure that the power supply cord is plugged in correctly, ie, into a working wall socket and into the LH10 Conversation Piece.
- Make sure that the battery is inserted correctly and is of the recommended type.
FAQ
-
Q: Where can I find an up-to-date user guide?
A: Please refer to our website at www.geemarc.com for an up-to-date user guide, as there may be important updates and changes you need to be aware of. -
Q: How can I get product support and help?
A: For product support and help, visit our website at www.geemarc.com . You can also contact us via email at help@geemarc.com or by telephone at 01707
- Q: Where is the product manufactured?
A: This product is made in China by Geemarc Telecom.
Please refer to our website: www.geemarc.com for an up-to-date user guide, as there may be important updates and changes you need to be aware of.
INTRODUCTION
Congratulations on purchasing your Geemarc LoopHEARTM10. The LoopHEARTM10 is a
rechargeable assistive listening device. It amplifies speech together with
sounds from a variety of sources like TV, radio and telephone.
The LoopHEARTM10 can be used as an alternative to Hearing Aids when using
headphones.
Note: users of digital hearing aids must make sure their aids have been programmed for use with the ‘T’ setting.
You must read the instructions below to use your Geemarc LoopHEARTM10 to their full potential. Keep this user guide in a safe place for future reference.
Unpacking the LoopHEARTM10
When unpacking the LoopHEARTM10, you should find the following in the box:
- LoopHEARTM10 Conversation Piece
- Headset with rubber ear cushions
- 3.7V Li-po Rechargeable Battery
- USB type C / USB A cable for recharging
- Lanyard (option)
- A microphone with “holder” and 3m lead (option)
- A belt clip
- 1 User Guide
For product support and help visit our website at
www.geemarc.com
E-mail: help@geemarc.com
Telephone: 01707 387602
lines are open 09h00 to 16h00 Mon to Fri
Parc de l’Etoile, 2 Rue Galilée, 59760 Grande-Synthe,
France
This product is made in China For Geemarc Teleco
DESCRIPTION
General Description
INSTALLATION
Setting Up
Open the battery compartment. Connect the supplied rechargeable battery (3.7V)
to the battery compartment located on the rear of the LH10 Conversation Piece.
Or insert 2 single batteries (1.5V AAA nonrechargeable) instead of the set battery supplied. With AAA battery mode, if the ‘On’ LED turns red when in use, the LH10 needs to have new batteries (No Red LED indication when using the rechargeable battery). To charge the battery, connect the supplied USB cable to the USB type C socket on the left-hand side of the unit and then into the USB socket to PC or standard power supply 5V DC. The power supply LED turns red.
Headset
Insert the headset lead into the headset port found on the base of the
Communication Piece.
USING THE LH10
Turning the LoopHEARTM10 On and Off
Switch the headset on. Ensure the mode switch is set to (MIC). Roll the On/Off
Volume control wheel upwards. The (On) LED will display Green. Adjust the
Volume to a comfortable level by rolling the On/Off Volume control wheel.
To turn the LH10 off, roll the On/Off Volume control wheel downwards. The
Green LED will switch off and OFF will be showing on the On/Off Volume control
wheel
The LH10 can be used in rooms specially equipped with a magnetic loop
(conference …etc) due to its “built-in T coil”. Simply by setting the mode
switch to T, the LH10 will receive the emitted magnetic waves then amplify
them to your headset. You will receive all the benefits of the “built-in T
coil”.
An external microphone (option) can be connected in the socket “Mic”, then set the switch to “Mic” position , in this case the “built in T coil” is disabled.
Microphone
The LH10 is built with an internal microphone which enables you to hear all
the surrounding sounds.
Tone and Balance Setting
The tone ( ) and Balance ( ) can be adjusted by using the controls found
within the battery compartment.
TROUBLESHOOTING
The ‘On’ LED is Red
- Charge the battery if the battery pack is used or replace it with new batteries if standard AAA batteries are installed.
The LH10 appears not to be working
- Make sure that the headset is securely plugged in.
- Make sure that the volume is correctly adjusted.
- Make sure that the battery is fully charged or use good batteries.
- Make sure the mode switch is set to MIC if using a headset/earpiece or T if using an induction loop.
The LH10 is not charging
- Make sure that the power supply cord is plugged in correctly i.e. into a working wall socket and into the LH10 Conversation Piece.
- Make sure that the battery is inserted correctly and is of the recommended type.
SAFETY INFORMATION
General
Do not open the unit. Contact the helpline for all repairs.
Cleaning
Clean the LH10 with a soft cloth. Never use polishes or cleaning agents – they
could damage the finish or the electrics inside.
Environmental
- Do not expose to direct sunlight.
- Always ensure there is a free flow of air over the surfaces of the LH10.
- Do not place any part of your product in water and do not use it in damp or humid conditions e.g. bathrooms.
- Do not expose your product to fire or other hazardous conditions.
- Avoid touching the LH10 Conversation Piece with clothing or hands, as this can create excessive noise.
GUARANTEE
From the moment your Geemarc LoopHEARTM10 is purchased, Geemarc guarantees it for 2 years. During this time, all repairs or replacements (at our discretion) are free of charge. Should you experience a problem then contact our helpline or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence, or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorized Geemarc representative. The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
DECLARATION: Geemarc Telecom SA hereby declares that this LoopHEARTM10
complies with the essential requirements and other relevant provisions of the
Radio Equipment Directive 2014/53/EU.
The declaration of conformity may be consulted at
www.geemarc.com
Radio Frequency (RF) power: <250 mW
FCC STATEMENT
FCC CLASS B
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used by the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. Suppose this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off
and on. In that case, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Re-orient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RECYCLING DIRECTIVES
The WEEE (Waste Electrical and Electronic Equipment) has been put in place for
the products at the end of their useful life to be recycled in the best way.
When this product is finished, please do not put it in your domestic waste
bin.
Please use one of the following disposal options:
- Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the product in an appropriate WEEE skip.
- Or, hand the old product to the retailer. If you purchase a new one, they should accept it.
Thus if you respect these instructions you ensure human health and
environmental protection.
All electrical and electronic products including batteries should be disposed
of separately from the municipal waste stream via designated collection
facilities appointed by the government or the local authorities. CAN
ICES-3(B)/NMB-3(B)
Parc de l’Etoile, 2 Rue Galilée,
59760 Grande-Synthe,
France
www.geemarc.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>