GEN2WAVE EID10 Alpha Biometric Terminal User Manual
- June 16, 2024
- GEN2WAVE
Table of Contents
EID10 Alpha USER MANUAL ID Secure LLC
Copyrights
The products described in this document may include copyrighted computer
programs. Laws in countries preserve for certain exclusive rights for
copyrighted computer programs.
Accordingly, any copyrighted computer programs contained in the products
described in this document may not be copied or reproduced in any manner
without the express written permission.
© 2023 ID Secure LLC All Rights Reserved
No part of this document may be reproduced, transmitted, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, without the prior written permission.
Furthermore, the purchase of our products shall not be deemed to grant either
directly or by implication, estoppel or otherwise, any license under the
copyrights, patents or patent applications, except for the normal non-
exclusive, royalty-free license to use that arises by operation of law in the
sale of a product.
Disclaimer
Please note that certain features, facilities, and capabilities described in
this document may not be applicable to or licensed for use on a particular
system, or may be dependent upon the characteristics of a particular mobile
subscriber unit or configuration of certain parameters.
Please refer to your contact for further information.
FCC compliance information
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may Cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may Cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.
This appliance and its antenna must not be located together or operated in
conjunction with any other antenna or transmitter.
A minimum separation distance of 20 cm must be maintained between the antenna
and individuals for this appliance to satisfy the RF exposure requirements.
Overview
Specification
General Characteristics| Dimensions| 78mm/3.07inch(W) x 112mm/4.41inch(H) x
30mm/1.18inch(D)
---|---|---
Weight| 164g
Communication| C Type USB Host : USB2.0 High Speed / 18PIN (USB Client/Host)
DATA CAPTURE| Fingerprint Reader| IB DANNO FAP 30 TFT PIV Certified
Sensor Type: Light-emitting sensor (LES) TFT camera
Resolution: 500 ppi
Gray Scale: 256 grayscale dynamic range
Image Size: 400W x 500H pixels
Supported Image Formats: RAW, JPEG2000, BMP, PNG, WSQ
FBI Certification / Image Certifications: PIV 071006, FIPS 201, FAP 30
Speed: Minimum frame rate > 10FPS
Capture Types: Single-finger flat
HID RFID Reader| HID OMNYKEY 5127CK-MINI 13.56 HF / 125K LF RFID
ISO14443A/B ISO15693, FeliCa™ (IDm), CEPAS (CSN)
Broad Credential Support NFC support for Mobile devices Dual frequency
allowingsimultaneous support for HF and LF credentials HID Prox, Indala® and
EM Prox,iCLASS, iCLASS SE® , iCLASS Seos® , MIFARE Classic® , MIFARE DESFire
EV1® iCLASS SE Processor Provides support for processing of PACS data and
secure keystorage and communication
User Environment| Operating Temp| -0℃ ~ 50℃ (-32℉ ~ 122℉)
Storage Temp| -20℃ ~ 60℃ (-4℉ ~ 140℉)
Humidity| Non-condensing, 93%
Drop| 1.5m (5ft.)
Compatible Device| RP1500, RP1600, RP1600X
Package / Device Features A. Device IO Connector
B. Device Locker
C. Fingerprint Reader
D. Cradle IO Connector
E. HID RFID Reader
F. USB C connector
Getting Started
Installing device
-
Installing the device
Attach the EID10 Alpha to the device as shown picture.
Insert the device down until the device latch snaps into place. -
Removing the device
Pushing the lockers on both sides of EID10 Alpha, pull the device out from the EID10 Alpha.
Charging & Cradle Interface
A. Device charging status LED
– OFF : Not charging
– Red LED : Charging
– Green LED : Fully charged
B. Spare battery charging status LED
– OFF : Not Charging
– Red LED : Charging
– Green LED : Fully Charged
** If the LED is off when the device or the sp are battery was mounted. Make
sure that RP1 600X/EID10PLUS is inserted correctly in the cradle or
RP1600X/EID10 Alpha is connected to a power source.
Using the NFC
Since HID RFID antenna is integrated in the rear side of the EID10 Alpha, read
the contactless card as shown.
NFC reading distance depends on the Card type.
Using the Fingerprint Reader
When reading a fingerprint, you need to touch finger on the outside of the
fingerprint reader sensor shown in the image (orange color) to read.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>