Knightsbridge VELOX 20A 3 Pin Lighting Connector User Manual

Knightsbridge VELOX 20A 3-Pin Lighting Connector

Product Information

Specifications

• Model: SN3P / SN4P

• Manufacturer: ML Accessories Ltd

• Supplied by: ML Accessories Ltd (UK), SLV Lighting Group (EU)

• Address: Unit E Chiltern Park, Boscombe Road, Dunstable LU5
  4LT

• Website: www.mlaccessories.co.uk

General Instructions
These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.  These instructions should be used to aid installation of the following products: SN3P / SN4P.

Safety
It is important to follow these safety guidelines:

• Read and understand all instructions before installation.
• Do not use aggressive cleaning products or solvents which may damage the product. Clean with a soft dry cloth only.
• Dispose of the product correctly at the end of its life. Check with local authorities for proper recycling facilities.

Installation
Follow the steps below for installation:

1. Refer to Fig. 1, Fig. 2, Fig. 3, and Fig. 4 for visual guidance during installation.
2. [Step 1]
3. [Step 2]
4. [Step 3]
5. [Step 4]

Maintenance
To maintain the product’s performance and lifespan, follow these maintenance guidelines:

• Regularly clean the product with a soft dry cloth.
• Avoid using aggressive cleaning products or solvents.

Warranty
The product is covered by the manufacturer’s warranty. For warranty information, contact ML Accessories Ltd or visit their website.

FAQ

Q: Where can I find recycling facilities for the product?

A: You can check with your local authorities to find the correct recycling facilities for the product.

Q: How do I clean the product?

A: Clean the product with a soft dry cloth only. Do not use aggressive cleaning products or solvents.

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and maintenance. These instructions should be used to aid installation of the following products: SN3P / SN4P

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Do not overload this accessory or subject it to conditions outside its rating
• This product is for indoor use only
• This product is IP20 rated

INSTALLATION

• Provide power to the required point of installation
• Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)
• sides of each half together to remove the cover(see Fig. 2)
• Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3
• the load side ensuring the correct polarity is observed (see Fig.4)
• Check all electrical connections are secure with all exposed copper within the terminal and no loose strands of cable
• all connections are secure with all exposed copper within the terminal and no loose strands of cable
• Refit the ensuring that the cables are secured by the cord grip
• Push the two halves together until the tab clicks in place
• switch on the correct operation

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents that may damage the product. This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.

**warranty

**

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserves the right to alter product specifications without prior notice.

SUPPLIED BY:
(UK) MANUFACTURER ML ACCESSORIES LTD, UNIT E CHILTERN PARK, BOSCOMBE ROAD, DUNSTABLE LU5 4LT, WWW.MLACCESSORIES.CO.UK (EU) SLV LIGHTING GROUP, DAIMLERSTRASSE 21-23, 52531 ÜBACH-PALENBERG, GERMANY
EMAIL : EPREL@GROUP.SLV.COM 
MADE IN CHINA

References

• SLV - Erlebe Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>