GL iNet GL-XE300 Puli 4G LTE Wireless Router User Manual
- June 16, 2024
- GL iNet
Table of Contents
GL-XE300 Puli 4G
LTE Wireless Router
User Manual
SETTING UP
-
Insert cards & Power on
When powered up,your GLIXERD0 routerwil broadcast Wi Fi signal with he SSID:
Hot plug for TF card and Nano SIM card are not supported for this router.
-
connectviawi-Fi
Connect to the Wi-Fi called 6GL-XE300-xxx,and input the default WiFi password Goodlife, which s also printed on the bottom of the router.
Connect via LAN
-
Set up Router
Visit http://192.168.8.1 in your browser o set up your outer; start by choosing your preferred language.
Product name| XE300 user manual| Color PANTONE:
* ciomovokzo
* c7em27vi5K0 ---|---|---
Material No| 505-0217
Size| 80*125mm
Print| Double / Color
Material| 1579 coated paper
Remarks| Single Card
(Last updated): 2020/12/15
SUPPORT
Repair / Reset
If you cannot access the web-based setup page o cannot connect to the route, you can press the Reset button:
- Press and hold for 3 seconds, and then release to repair your network.
- Press and hold for 10 seconds, and then release to reset the router to factory settings. Al user data will be cleared.
https://docs.gl-inet.com/en/3/
Technical Supports
- For more detailed and updated instructions, please visit our website: docs.gl-inet.com
- For further questions, you can get help from the following ways: Email o [email protected]
- Message us on our Facebook: facebook.com/gl.inet.wifi/
- Post questions in our forum: forum.glinet.com
- Ask professionals in other forums e.g. Openrt, LEDE o other professional websites
WARRANTY
- We provide one year limited warranty for routers and 3-month limited warranty for accessories. Extra warranty may apply according to the local law in which the product purchase took place.
- Highly recommend using the included S¥/2A power adapter.
- Any damage to the routes caused by not following the instructions will render this warranty full and void.
- Any damage to the routes caused by modifying the PCBA, components of case will render this warranty null and void.
- Issues caused by the use of third-party firmware may not get official support from us.
- Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high temperature, dropping in the water of on the ground will render this warranty null and void.
- Pictures on the instructions are only for reference. We reserve the right to change or modify these materials without further notice.
- Keep your device within the recommended operating temperature (0°C to 40°C). Recommend storage temperature for your device is between -20°C to +45°C. Please note lower or higher temperatures may cause damage to the device.
- To avoid battery or device failure, do not remove or replace the nomremovable battery.
- The device should shut down due to overheating (in the event the battery temperature exceeds 60°C).
FCC ID: 2AFIW-XE300C4 | 2AFIW-XE300C6 | 2AFIW-XE300C4G
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
Note: This equipment has been tested and found to comply with the limits for a Class 6 digital device, pursuant to part 15 of the FCC Rules. These limits are desiqned to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hasmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the uses is encouraged to try to correct the interference by one of more of tive following measures:
– Reorient of relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TY technician for help important announcement.
Radiation Exposure Statement
D Specific Absorption Rate (SAR) information:
This 4G LTE Wireless Router meets the government’s requirements for exposure
to radio waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies.
The standards include a substantial safety margin designed to assure the
safety of all persons regardless of age or health.
e FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 Wikg averaged over one gram of tissue.
Device types:
4G LTE Wireless Router (FCC ID: 2AFIW-XE300C4G) has also been tested against
this SAR limit.
The highest SAR value reported under this standard during product
certification for property worn on the body is 1.082W/kg. This device was
tested for typical body-worn operations with the back of the handset kept Omm
from the body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a Ohm separation distance between the user’s body
and the back of the handset. The use of beit clips, holsters and similar
accessories should not
contain metallic components in its assembly. The use of accessories that do
not satisfy these requirements may not comply with FCC AF exposure
requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of Ømm must be maintained
between the user’s body and the handset, including the antenna. Third-party
belt-clips, holsters, and similar accessories used by this device should not
contain any metallic components.
Body-worn accessories that do not meet these requirements may not comply with
RF exposure requirements and should be avoided. Use only the supplied or an
approved antenna.
The Equipment named above is confirmed to comply with the requirements setout
in the European Council Directive on the Approximation of the Laws of the
Member States relating to RED (2014/53/EU). The equipment passed the test
which was performed according to the following European standards:
EN 300 328 V2.2.2(2019-07); EN 301 908-1 V13.1.1(2019-11); EN 301 489-1
V2.2.3(2019-11); EN 301 489-17 V3.1.1(2017-02);
EN 301 489-52 V1.1.0(2016-11); EN 55032:2015; EN 55035:2017; EN 50566:2017& EN
62209-2:2010+A1:2019; EN 62368-1:2014+A11:2017
This product uses WiFi 2.4GHz Operating Frequency is 2400~2483.5MHz/20dBm;
5GHz Operating Frequency is 5150~5250MHz (indoor use only)/23dBm.
RF Exposure: The highest measured 10g (simultaneous transmission) Body SAR max
value is: 1.602 W/kg (GL-XE300C4) and 1.744 W/kg (GL-XE300C6). (Limit 2.0W/Kg)
restriction info: Restriction in BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR,
IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, Fl, SE,
UK. The Product comply with Directive 2011/65/EU and its amendment directive
2015/863/EU (Rohs2.0)
Hong Kong Office
GL Technologies (Hong Kong) Limited
Unit 203, 2/F, Building 19W, 19 Science Park West
Avenue, Hong Kong Science Park,
Pak Shek Kok, NJ., Hong Kong| Shenzhen Office
Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305 – 306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
( +86-0755-86606126 )
---|---