vtech 80-550900 Drill and Learn Toolbox Pro Instruction Manual

: June 4, 2024
: vtech

Table of Contents

vtech 80-550900 Drill and Learn Toolbox Pro
INTRODUCTION
PRODUCT OVERVIEW
INCLUDED IN THE PACKAGE
Tool Belt Assembly
GETTING STARTED
BATTERY INFORMATION
ACTIVATING NORMAL PLAY MODE
PRODUCT FEATURES
ACTIVITIES
SONG LYRICS
CARE & MAINTENANCE
TROUBLESHOOTING
IMPORTANT NOTE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

vtech 80-550900 Drill and Learn Toolbox Pro

vtech 80-550900 Drill and Learn Toolbox Pro -fig1

INTRODUCTION

Thank you for purchasing the Drill & Learn ToolboxTM Pro!
Get ready for fix-it fun with the drill, hammer and wrench while learning cool tool facts, numbers, colors, objects and more. Use the project cards, follow the instructions and enjoy the imaginative repair play. Put on your tool belt to take the fun on the go!

PRODUCT OVERVIEW

vtech 80-550900 Drill and Learn Toolbox Pro -fig2

Holes
Tool Buttons
Mode Selector
Card Slot
On/Off/Volume Selector 6 Belt Piece A
Belt Piece B
Hammer
Wrench
Nails
Screws
Project Cards
Direction Switch
Drill

INCLUDED IN THE PACKAGE

Drill & Learn Toolbox™ Pro
2 project cards
1 tool belt
1 drill
1 hammer
1 wrench
2 screws
2 nails
Quick Start Guide

Tool Belt Assembly

Slide the end of Belt Piece A through the slots on the end of Belt Piece B.
Snap together.
Buckle the belt on the child’s waist to play.

vtech 80-550900 Drill and Learn Toolbox Pro -fig3
WARNING
All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety.
NOTE
Please save this Instruction Manual as it contains important information.

Unlock the Packaging Locks

Rotate the packaging locks 90 degrees counterclockwise.
Pull out the packaging locks and discard.
Turn the packaging locks counterclockwise several times.
Pull out and discard the packaging locks.
WARNING
Do not insert anything other than the included screws or nails into the holes of the toolbox. Doing so may damage the toolbox.

GETTING STARTED

Battery Removal and Installation

Make sure the unit is turned Off.
Find the battery cover located on the bottom of the unit, use a screwdriver to loosen the screw and then open the battery cover.
Remove old batteries by pulling up on one end of each battery.
Install 2 new AA size (AM-3/LR6) batteries following the diagram inside the battery box.
(For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended.)
Replace the battery cover and tighten the screw to secure.

WARNING:

  * Adult assembly required for battery installation.
  * Keep batteries out of reach of children.

BATTERY INFORMATION

Insert batteries with the correct polarity (+ and -).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
Only batteries of the same or equivalent type as recommended are to be used.
Do not short-circuit the supply terminals.
Remove batteries during long periods of non-use.
Remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of batteries in fire.

RECHARGEABLE BATTERIES:

Remove rechargeable batteries from the toy before charging.
Rechargeable batteries are only to be charged under adult supervision.
Do not charge non-rechargeable batteries.

ACTIVATING NORMAL PLAY MODE

When the product is taken out of the packaging, turn it on and insert a Project Card. You will hear a beep and a voice confirming you are in Normal Play mode.

PRODUCT FEATURES

On/Off/Volume Selector
To turn the unit On or adjust the volume, slide the selector to Low or High. To turn the unit Off, slide the selector to Off.
Mode Selector
Slide the Mode Selector to choose an activity. Choose from three activities.
Tool Buttons
Press the Tool Buttons to learn about tools, answer questions or listen to cheerful songs.
Holes
Drill the Screws or hammer the Nails into the Holes to play or answer questions.
Project Cards
Insert one of the two double-sided Project Cards into the Card Slot to explore tools and to hear fix-it songs about tools, numbers, vehicles and housewares.
Tool Belt
- Insert the tools into the loops on the Tool
- Belt for fix-it fun.
Drill
- Use the Drill to drill Screws into the
- Holes. The Drill can turn clockwise or counterclockwise by sliding the Direction
- Switch on the side.
Hammer
Use the Hammer to insert the Nails into the Holes.
Wrench
Use the Wrench to insert the Screws into the Holes.
Automatic Shut-Off
- To prolong battery life, the Drill & Learn ToolboxTM Pro will shut off automatically after several minutes without input. The unit can be turned on again by sliding the On/Off/Volume Selector or sliding the Mode Selector.
- The unit will also automatically turn off when the batteries are very low.

ACTIVITIES

Free Play Mode
Press the three Tool Buttons to learn about tools, sounds and colors. Use the Drill, Hammer or Wrench to drill Screws or hammer Nails into the Holes. If no Project Card is inserted, you will hear sounds and phrases. If a Project Card is inserted, you can learn about numbers, more than or less than, tools, colors, vehicles, objects and more. After every five actions (drill a Screw, hammer a Nail, etc.), a song plays in celebration.
Challenge Mode
Tool time! Listen to the questions and answer them by using the tools or pressing the Tool Buttons. When all the Screws and Nails are inserted into the Holes, pull them out and continue to answer other questions.
Music Fun Mode
Press the Tool Buttons or insert a Project Card to hear songs about tools, numbers and objects. Listen to the fun melodies by drilling a Screw or hammering a Nail into the Hole.

SONG LYRICS

Tools Card
- We are fixers with lots of tools Safety first, that’s the rule.
- No job is too big,
- No job is too small,
- With the right tools,
- We can do them all!
Numbers Card
- One, two, three
- Count with me.
- Four, five, six
- What should we fix?
- Seven, eight, nine
- We’re fixin’ all the time.
Vehicles Card
- Scoot, fly, zig and zag
- In the boat, paddle, paddle The excavator digs, digs,
- All go fast and slow
- And all need special care to fix.
Housewares Card
- Well, it might be a little bit noisy
- All of our repairs
- Fixing things around the house
- Well, it takes work and skill
- When it’s fixed, what a thrill!
Wrench Song
- Twist and turn the bolt to learn
- How to use the wrench
- To the right, right, right
- To make it tight, tight, tight
- To the left, left, left
- To make it loose, loose, loose.
Hammer Song
- Hammers and nails
- Go together like
- Shells on snails
- Or water and whales
- Or colors on peacock tails.
Drill Song
- When we use the drill
- Hold it steady, hold it still
- Line it up with the screw
- Squeeze the drill and vroom, vroom, vroom!

CARE & MAINTENANCE

Keep the unit clean by wiping it with a slightly damp cloth.
Keep the unit out of direct sunlight and away from any direct heat source.
Remove the batteries if the unit will not be in use for an extended period of time.
Do not drop the unit on hard surfaces and do not expose the unit to moisture or water.

TROUBLESHOOTING

If for some reason the unit stops working or malfunctions, please follow these steps:

Turn the unit Off.
Interrupt the power supply by removing the batteries.
Let the unit stand for a few minutes, then replace the batteries.
Turn the unit On. The unit should now be ready to play again.
If the unit still does not work, install a new set of batteries.

IMPORTANT NOTE

If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S., 1-877-352-8697 in Canada, or by going to our website vtechkids.com and filling out our Contact Us form located under the Customer Support link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information

Trade Name: VTech®
Model: 5509
Product Name: Drill & Learn Toolbox™ Pro
Responsible Party: VTech Electronics North America, L.L.C.
Address: 1156 W. Shure Drive, Suite 200 Arlington Heights, IL 60004
Website: vtechkids.com
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-003(B)/NMB-003(B)