dji C8000 Intelligent Battery Station User Guide

C8000 Intelligent Battery Station
User Guide
v1.0

Disclaimer

Congratulations on purchasing your new DJITM product. Read this entire document and all safe and lawful practices DJI provided carefully before use. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this document carefully and that you understand and agree to abide by all terms and conditions of this document and all relevant documents of this product. You agree to only use this product for purposes that are proper. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. DJI accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product.
DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by DJI with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of DJI.
This document and all other collateral documents are subject to change at the sole discretion of DJI.
For up to date product information, visit http://www.dji.com and click on the product page for this product.
This document is available in various languages. In the event of divergence among different versions, the English version shall prevail.

Warning

1. The power cable of the AC input current is 16 A. Use two separate power outlets of a total current exceeding 32 A. A certain power margin is required for safety.
2. DO NOT connect two AC power cables simultaneously when using the battery station indoors.
3. This product serves for charging aircraft that are used for certain purposes. Before using such aircraft, make sure you understand and comply with the local laws and regulations and, if required, have obtained corresponding approval and clearance from the related government agencies.
4. DO NOT use this product under direct sunlight, in rain, or in a damp environment.
5. Keep the battery station away from heat, pressure, water, flammable gases, and corrosives.
6. The battery station should be kept in an environment with a temperature range of -20° to 45° C (-4° to 113° F).
7. Place the battery station on a flat and stable surface. In order to prevent fire hazards, make sure the device is properly insulated and that there is sufficient space for ventilation (at least 50 cm).
8. In case of fire, make sure to use a dry powder fire extinguisher. A liquid fire extinguisher may lead to an electrical hazard.
9. DO NOT unplug the AC cable or charging cable while the battery station is in use. Remove batteries after charging is complete.
10. If there is any noticeable buildup, wipe the battery station or power ports with a clean, dry cloth.
11. DO NOT use the battery station during a thunderstorm.
12. Refer to the document of the batteries for more safety instructions before use.
13. DO NOT hold the charging cables to carry the battery station. Otherwise, the cables may be damaged.
14. DO NOT use the battery station in an area where batteries are stored. There should be a distance of at least 30 cm between the battery station and any charging batteries. Otherwise, the battery station or charging batteries may be damaged by excessive heating and may even lead to a fire hazard.
15. Keep the battery station away from inflammable materials while charging. DO NOT place the battery station or charging batteries on a blanket or any carpeted surfaces when in use.
16. For activation or firmware updates, the battery station can be connected to the DJI ASSISTANTTM2 (MG Series) / (Delivery Drones Series) or the remote controller. Make sure the remote controller firmware and the DJI Assistant 2 software have been updated to the latest version before use.

Introduction

The C8000 Intelligent Battery Station can connect with up to two batteries. While charging, the battery station monitors the status of the batteries and can automatically adjust the charging current if required. The battery station continues to charge even if the ventilation holes are blocked.
Users can check the battery charging status LEDs and the warning indicator on the operation panel of the battery station to confirm if there are any errors. The battery station can be connected to a remote controller using a USB-C cable and users can launch the app compatible with the aircraft to check more detailed information regarding any errors. Additionally, the battery station has the following functions: overcurrent protection, overcharging protection, under-voltage protection, overheating protection, and status display.

Overview

Battery Station

1. Operation Panel
2. Charging Cables Clamp
3. Front Panel Dustproof Cover
4. Charging Cables Storage
5. Handle
6. Charging Cable
7. USB-C Port (for device activation and firmware updates)
8. AC Power Port
9. AC Power Dustproof Cover
10. GND Port (with a diameter of 4 mm)
    Use the cable as shown below to connect the GND port and the ground.

Operation Panel

1. Charging Status LED × 2
   Each LED indicates the charging status of the battery connected to a charging cable. The numbers (1-2) correspond to the position of the charging cable on the battery station.

2. Warning Indicator
   The warning indicator will be on if the battery station detects any abnormalities. If the indicator turns solid yellow, connect the battery station to a remote controller using a USB-C cable to confirm if there are any errors.
   If the indicator turns solid red, stop charging immediately. Only start to charge again once the indicator is no longer solid red.

3. Power Button
   Press to power the battery station on and off. It is recommended to press the power button and unplug the AC power cable to power off the station.

Activation

The battery station requires activation before using for the first time. If the warning indicator is solid green, it means the battery station has not been activated. Follow the steps below to activate the battery station:

Method 1: Using the App

1. Connect the battery station to a power outlet.
2. Connect the battery station to the USB-A port on the remote controller using a USB-C cable.
3. Press the power button to power on the battery station.
4. Run the app compatible with the aircraft and follow the prompts to finish activation.

Method 2: Using DJI Assistant 2 (MG Series) / (Delivery Drones Series)

1. Connect the battery station to a power outlet.
2. Connect the battery station to the computer using a USB-C cable.
3. Visit www.dji.com to download DJI Assistant 2 (MG Series) / (Delivery Drones Series). Install and run the software.
4. Press the power button to power on the battery station.
5. Use your DJI account to log in and click the corresponding charging device and follow the prompts to finish activation.

Make sure the computer or remote controller is connected to the internet during activation.

Using the Battery Station

Up to two batteries can be connected to the battery station. Follow the instructions below to use the battery station.

1. Connect the battery station to a power outlet.
   **** Each AC power cable must be connected to a separate AC power outlet or power strip with a rated current of more than 16 A.
   Only use one AC power cable when using the battery station indoors. This will reduce the maximum power output by half.
   *Users can set the max charging power limit in DJI Assistant 2 according to their requirements to avoid safety risks such as short circuits due to excessive power.

2. Connect the battery to the battery station. Make sure to place the charging battery on the same side that the charging cable is fixed to the battery station.

3. Make sure all cables are correctly connected and press the power button on the operation panel of the battery station. The two LEDs and the warning indicator will flash simultaneously.
   After powering on, the only lights remaining will be the charging status LEDs, which represent the batteries currently connected. This indicates that self- diagnosis is complete and the device is working normally. For more information about how to check if there are any errors during self-diagnosis, refer to the LEDs and Warning Indicator Description. Alternatively,  connect the battery station to a remote controller and launch the app for more detailed information about the errors.

4. If no errors are detected during self-diagnosis, the battery station will begin to charge the batteries.
   Using DB2000 Intelligent Flight Batteries: if two batteries are connected simultaneously, the battery station will charge the battery with less power first. When the two batteries show the same power, the battery station will charge the batteries simultaneously.
   Using other batteries: if two batteries are connected simultaneously, the battery station will charge the batteries in order of their power level, starting from highest to lowest.
   • Before use, make sure there are no obvious defects on the battery station or batteries (e.g., jams, breakages, or short circuits).
   • DO NOT power the battery station on unless the batteries are correctly connected.
   • When using DB2000 Intelligent Flight Batteries, the battery station will warm up a battery to 22° C (72° F) before charging if the battery station detects a low- temperature battery. When using other batteries, the battery station will automatically adjust the charging current based on the condition of the batteries. For example, if the battery temperature is below 15° C (59° F), the charging current will be limited and the charging time will be longer. The charging time depends on the battery model and battery temperature. The lower the battery temperature, the longer the charging time will be. The charging temperature range varies depending on the battery model. Refer to the document of the battery to check the charging temperature range.

LEDs and Warning Indicator Description

During charging, the status LED will blink when the corresponding charging battery is experiencing an abnormality due to the cable being disconnected, a high or low temperature, overvoltage, or overcurrent. Once charging is complete, the status LED will be solid green. The battery can be disconnected from the battery station.

Battery Station Status:

LEDs| Warning Indicator| Power Button Indicator| Description
---|---|---|---
/| Solid green| /| The battery station is ready to be activated, or
under loader stage
Solid
yellow| Solid yellow| Solid green| Self-diagnosis and power supply of the battery
station are normal
/| /| Solid green| The battery station is ready to connect to a battery
Solid
yellow| Blinks yellow twice
continuously| /| The battery station logs are being exported and
it has stopped charging. Restart the battery
station after the logs have been exported

Charging Indicators:

queued to charge
Blinks green| /| The battery corresponding to the number is charging I
Solid green| /|  The battery corresponding to the number is Cully charged I
Blinks yellow once continuously| /| The battery corresponding to the number is warming up
Blinks yellow three times continuously| /| The temperature of the battery corresponding to the number is too low and the battery station has stopped charging
Blinks yellow four times continuously| /| The temperature of the battery corresponding to the  number is too high and the battery station has stopped charging
Blinks red once continuously| Beeps once continuously| The battery in the corresponding position is not correctly connected or an unauthorized battery is connected. This warning will only appear 10 seconds after the battery is connected
Blinks red twice continuously| Beeps twice continuously| The connector short- circuited. Check the battery or the battery station
Solid red| Beeps three times continuously| Critical error detected

The warning indicator will light up if one of the following problems occur while using the battery station:

abnormal and the power is limited
Blinks red once continuously| /| The CPX503-3000 switching power supply is unavailable or the fan stalled
Blinks red once continuously| Beeps once continuously|  The CPX503-3000 has experienced a critical error and there is no output
Solid red| Beeps twice continuously| Main board is abnormal and unavailable

If there are any abnormalities, connect the battery station to a remote controller and run the app compatible with the aircraft to check more information. If the app indicates that a module is abnormal or broken, contact DJI or a DJI authorized dealer.

Updating Firmware

Follow the instructions below to update the firmware using the remote controller or DJI Assistant 2 (MG Series) / (Delivery Drones Series). Users will be notified through the app when firmware updates are available.

Using Remote Controller

1. Connect the battery station to a remote controller using a USB-C cable and connect the battery station to a power outlet.
2. Power on the remote controller and press the power button on the operation panel to power on the battery station.
3. Run the app compatible with the aircraft and follow the prompts to update the firmware.
   Make sure the remote controller remains connected to the internet while updating.

Using DJI Assistant 2 (MG Series) / (Delivery Drones Series)

1. Download DJI Assistant 2 (MG Series) / (Delivery Drones Series) at https://www.dji.com/downloads.
2. Launch the software and log in with your DJI account.
3. Power on the battery station and connect the station to a computer via the USB-C port.
4. Select the corresponding charging device and click on Firmware Updates on the left panel.
5. Select the firmware version that you wish to update to.
6. Wait for the firmware to download. The firmware update will start automatically.
7. The station will reboot automatically after the firmware update is complete.

• Before using the battery station, make sure there are no obvious defects on the ports or cables of the battery station (e.g., jams, breakages, or short circuits).
• DO NOT connect the batteries while updating the firmware of the battery station.
• DO NOT disconnect the battery station while updating the firmware of the battery station.
• Make sure the computer is connected to the internet.
• Retry if update fails.

Storage and Maintenance

Battery Station Storage
When the battery station is not in use, disconnect the batteries from the battery station and the battery station from the power outlet. Follow the steps below to safely secure the charging cables.

1. After disconnecting a battery, wrap the charging cable over the battery station.
2. Make sure the end of the charging cable is securely attached to the corresponding storage on the side of the battery station. • DO NOT store this product under direct sunlight, in rain, or in a damp environment.
   • Keep the battery station away from heat, pressure, water, flammable gases, and corrosives.

Battery Station Maintenance

Clean the AC power dustproof cover and front dustpoof cover regularly to ensure the charging performance is unaffected.

Specifications

220-240 V, 50/60 Hz, 15 A
Input 2| 100-120 V, 50/60 Hz, 15 A
220-240 V, 50/60 Hz, 15 A
Battery Station Output| 59.92 V, 100 A (with an input voltage of 220-240 V)
59.92 V, 40 A (with an input voltage of 100-120 V)
Compatible Battery| DB2000/DB1560/DB800/140/T2OP/T30 Intelligent Flight Battery
Weight| Approx. 11.5 kg I

Compliance Information

FCC Compliance Statement
Supplier’s Declaration of Conformity
Product name: C8000 Intelligent Battery Station
Model Number: CHX101-7000
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com

We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED Compliance
CAN ICES-003 (A) / NMB-003(A)
EU & UK Compliance Notice

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (C8000 INTELLIGENT BATTERY STATION) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/35/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance
EU contact address: DJI GmbH, Lndustriestrasse 12, 97618, Niederlauer, Germany Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (C8000 INTELLIGENT BATTERY STATION) is in compliance with the essential requirements and other relevant provisions of Electrical Equipment (Safety) Regulations 2016.
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

WE ARE HERE FOR YOU

| |
---|---|---
https://www.facebook.com/qr/901489424133812| https://www.youtube.com/c/DJIAgriculture| http://weixin.qq.com/r/jjqCms- EDZJyrYv592_c

For the latest information on Agras products, scan the Facebook or YouTube QR code.

|
---|---
http://weixin.qq.com/r/jjqCms-EDZJyrYv592_c| http://weixin.qq.com/r/OxM0LHDEkS3urTRP90Yp

This content is subject to change without prior notice.
If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com.
DJI and AGRAS are trademarks of DJI.
Copyright © 2023 DJI All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>