Zigbee SR-ZG9101CS LED Controller Instructions

Zigbee LED Dimmer 09.ZG901CS.04007
Important: Read All Instructions Prior to Installation

Function introduction

Product Data

No| Input Voltage| Output Current| Output Power| Remarks| Size(LxWxH)
---|---|---|---|---|---
1| 12-48VDC| 1x8A@12-36VDC
1x4A@48VDC| 1x(96-288)W@12-36VDC
1x192W@48VDC| Constant voltage| 95x37x20mm
2| 12-48VDC| 1x350mA| 1x(4.2-16.8)W| Constant current| 95x37x20mm
3| 12-48VDC| 1x700mA| 1x(8.4-33.6)W| Constant current| 95x37x20mm

• ZigBee LED dimming light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF and light intensity of connected LED lights
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator
• Enables to add devices to the self-formed zigbee network
• Supports slef-forming zigbee network without coordinator and add other devices to the network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20

Safety & Warnings

• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.

Operation

1. Do wiring according to connection diagram correctly.

2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
   Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
   Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
   Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), the network pairing mode will last until the device is added to a zigbee network.
   

4. TouchLink to a Zigbee Remote
   Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation.
   Method 2: If the device is already added to a network, it will be set into Touchlink commissioning immediately, 180S timeout. Once timeout, re-power on the device to set it into touchlink commissioning again.
   Note:

1. Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2. TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3. To control by both gateway and remote, add remote and device to network first then TouchLink.
4. After TouchLink, the device can be controlled by the linked remotes.

5. Removed from a Zigbee Network through Coordinator or Hub Interface
   

6. Factory Reset Manually
   Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if the “Prog.” key is not accessible.
   Note: All configuration parameters will be reset after the device is reset or removed from the network.

7. Factory Reset through a Zigbee Remote (Touch Reset)
   Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.
   Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.

8. Find and Bind Mode
   Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.
   

9. Learning to a Zigbee Green Power Remote
   Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation.
   

10. Delete Learning to a Zigbee Green Power Remote
    Step 1: Short press “Prog.” button 3 times (Or re-power on the device 3 times) to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation.
    

11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
    Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation.
    Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals.
    Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
    Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.
    Note:

1. Each added device can link and be controlled by max. 30 added remotes.
2. Each added remote can link and control max. 30 added devices.

12. ZigBee Clusters the device supports are as follows:
    Input Clusters
    • 0x0000: Basic
    • 0x0003: Identify
    • 0x0004: Groups
    • 0x0005: Scenes
    • 0x0006: On/off
    • 0x0008: Level Control
    • 0x0b05: Diagnostics
    Output Clusters
    • 0x0019: OTA

13. OTA
    The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

14. Controlled by a push switch:
    Once connected with a push switch, click the push switch to switch ON/OFF, press and hold down it to increase/decrease light intensity.

Product Dimension

Wiring Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>