Knightsbridge FLTW 230V IP65 18W LED White Twin Spot Floodlight Instruction Manual

Knightsbridge FLTW 230V IP65 18W LED White Twin Spot Floodlight

GENERAL INSTRUCTIONS

• These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.
• These instructions should be used to aid installation of the following products: FLTB/FLTW/FLTPB/FLTPW

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt. consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class I and must be earthed

INSTALLATION

Note
If this product is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable-rated Junction boxes should be used where required
• Remove the two screws from the front of the fitting and remove the baseplate (see Fig. 1)
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to infringe on any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain the IP rating, and secure the baseplate to the surface (see Fig. 2)
• To ensure correct polarity is observed, carefully wire as shown in Fig. 3
• Fit the luminaire onto the baseplate and secure it with the two screws
• Cover the screws with the screw caps provided
• Switch on and check for the correct operation

PIR SETTINGS

The PIR sensor (FLTPx only) is factory set as follows (these settings are not adjustable):

• Detection range: maximum 8m when mounted at a height of 2.4m
• Time settings: 90 seconds
• Lux settings: below 30 lux
• Detection angle: 120°

Manual override can be activated by switching the power off and on twice within 3 seconds. This will turn the luminaire on for approximately 8 hours, after which it will reset automatically. The override can be cancelled by switching the power off and on twice within 3 seconds.

WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed. This product is not suitable for installation in or near a coastal or marine environment.

GENERAL INSTRUCTIONS

• This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
• This product contains a non-replaceable LED light source and control gear
• Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not use aggressive cleaning products or solvents that may damage the product.
• Do not use any source of high-pressure washers to maintain or clean this luminaire.
• This product is non-dimmable.
• This product should be dismantled for disposal when it reaches the end of its life. Please see the website for dismantling instructions.
• This product should be recycled correctly when it reaches the end of its life. Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 3 years from the date of purchase. Failure to install this product per the current edition of the IEE Wiring Regulations (BS 7 6 71), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product.

SUPPLIED BY:

• (UK) MANUFACTURER ML ACCESSORIES LTD, UNIT E CHILTERN PARK, BOSCOMBE ROAD, DUNSTABLE LU5 4LT, WWW.MLACCESSORIES.CO.UK.
• (EU) SLV LIGHTING GROUP, QAIMLERSTRASSE 21-23, 52531 UBACH-PALENBERG, GERMANY
• EMAIL: EPREL@GROUP.SLV.COM.

MADE IN CHINA.

ML Accessories Limited LUS 4LT
www.mlaccessories.co.uk.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>