LITETRONICS AL1503 Selectable Type III LED Bronze Area Light Instruction Manual
- June 16, 2024
- Litetronics
Table of Contents
Area Light
Installation Instructions
AL-Series
AL1503 Selectable Type III LED Bronze Area Light
WHAT COMES IN THE BOX
3 pin shorting cap
Pluggable sensor socket
3 1/2 ft cable, Type 3 lens
Installation Instructions
TOOLS NEEDED
Phillips Screwdriver
Allen Wrench
SAFETY INSTRUCTIONS AND WARNINGS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE
OBSERVED.
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
Litetronics fixtures must be wired in accordance with the National Electrical
Code and all applicable local codes.
Risk of fire or electric shock. Area light installation requires knowledge of
luminaires electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
Be certain electrical power is OFF before and during installation and
maintenance.
Area light must be connected to a wiring system with an equipment – grounding
conductor.
Make sure the supply voltage is the same as the rated luminaire voltage.
Only the open holes indicated in the photographs and/or drawings may be made
or altered as a result of this kit installation. Do not leave any other open
holes in an enclosure of wiring or electrical components.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet
metal or sharp objects.
Suitable for wet locations.
ATTENTION
- Please check if there is any damage during shipping. If so, please contact Litetronics customer service.
- Please read the installation instruction carefully to check whether all the accessories are included.
- After confirmation, install the fixture according to installation steps.
INSTALLATION PROCEDURE
WIRING DIAGRAM As for the wire color of DIM+ and DIM-,pl s check the lamp
label.
120V & 277V
| GROUND | GREEN |
|---|---|
| NETURAL | WHITE |
| LINE (HOT) | BLACK |
Figure 1
*For 240V, follow 480V wiring instructions
| GROUND | GREEN |
|---|---|
| LINE 1 (HOT) | WHITE |
| LINE 2 (HOT) | BLACK |
Figure 2
*For 347V, follow 120-277V wiring instructions
INSTRUCTIONS FOR SHORTING CAP
1. Unless optional Photocell device (Ordered Separately) is to be installed,
shorting cap should be installed on the back of light:
(Figure 3) 2. CCT & Wattage adjustment (Figure 4)
Step 1 : Unscrew the 3/4 plug (CCT & Wattage Selector)
Step 2: Adjust the integrated switch for CCT & Wattage adjustment to get
the desired CCT and Wattage according to the label on the fixture;
Step 3: Install and tighten the 3/4 plug; AL1503
WATTAGE SLIDE SWITCH SETTINGS
150W………………… 125W……………….. 100W
Note: Watts default setting set to 150W.
CCT SLIDE SWITCH SETTINGS
5000K……………….. 4000K ………………….3000K
Note: CCT default setting set to 5000K.
AL2003
WATTAGE SLIDE SWITCH SETTINGS
200W ………………175W……………….. 150W
Note: Watts default setting set to 200W.
CCT SLIDE SWITCH SETTINGS
5000K…………………. 4000K …………………3000K
Note: CCT default setting set to 5000K.
AL3003
WATTAGE SLIDE SWITCH SETTINGS
300W…………………… 270W……………….240W
Note: Watts default setting set to 300W.
CCT SLIDE SWITCH SETTINGS
5000K………………….. 4000K……………………. 3000K
Note: CCT default setting set to 5000K.
INSTALLATION PROCEDURE
THE LENS DEFAULT SETTING, THE CENTER MARKER ON THE FIXTURE IS SET TO “TYPE
III”. (FIGURE 7)
Lens rotation instructions (if required). To rotate the lens follow the next
steps:
Step 1: Turn off power.
Step 2: Using a Phillips screwdriver, unscrew the 25 screws that hold the
lens in place.
Step 3: Remove lens.
Step 4: To adjust lens to a left/forward distribution rotate lens
clockwise 90°. To confirm proper rotation, the letter “L” should be correctly
set at the center square slot at the base of the fixture. (Figure 8)
Step 5: To adjust lens to a right/forward distribution rotate lens
counter-clockwise 90°. To confirm proper rotation, the letter “R” should be
correctly set at the center square slot at the base of the fixture. (Figure 9)
Step 6: Secure lens is in the proper position and replace all 25 screws.
Step 7: Make sure the installation is complete and secure before turn on
the power.
The information and product specifications contained in these instructions are
based upon data believed to be accurate at the time of printing. This
information is subject to change without notice and without incurring
liability.
If you have questions regarding specific product details, please contact us at
800-860-3392 or via email at
customerservice@litetronics.com.
To check for an updated version of these instructions, please visit
www.litetronics.com.
Thank you for choosing
6969 W. 73rd Street
Bedford Park, IL 60638
WWW.LITETRONICS.COM
CustomerService@Litetronics.com or
1-800-860-3392
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>