Arissa ARGMBATHT Wall Mounted Bath Shower Mixer Instruction Manual

Arissa ARGMBATHT Wall Mounted Bath Shower Mixer

Specifications

• Product Name: Arissa ARGMBATHT Wall Mounted Bath Shower Mixer
• Model Number: [Model Number]
• Dimensions: [Dimensions]
• Weight: [Weight]
• Material: [Material]

Installation

1. Ensure that you have all the necessary tools and equipment for installation.
2. Select a suitable location for the product.
3. Follow the provided installation instructions to securely mount the product.
4. Double-check the stability and ensure that the product is properly installed.

Using the Product

To use the product

1. Make sure the product is properly installed and stable.
2. Read and understand the user manual for any specific usage instructions.
3. Follow the recommended guidelines and safety precautions while using the product.
4. If applicable, adjust any settings or controls according to your preference.

Cleaning and Maintenance

To keep the product in good condition, follow these cleaning and maintenance instructions:

• Regularly clean all surfaces of the product using a mild detergent and a soft cloth.
• Avoid using abrasive cleaners or materials that may scratch or damage the product.
• Wipe off any spills or stains immediately to prevent potential damage.
• Inspect the product periodically for any signs of wear or damage.

FAQs

• Q: What should I do if the product starts peeling?
  A: Peeling problems caused by improper installation, usage, cleaning, or maintenance are not covered by the product warranty. To prevent peeling, ensure that you carefully follow the installation and cleaning instructions provided.

• Q: Can I use abrasive cleaners to clean the product?
  A: No, it is recommended to avoid using abrasive cleaners as they can scratch or damage the product. Instead, use a mild\ detergent and a soft cloth for cleaning.

• Q: How often should I clean the product?
  A: It is recommended to regularly clean the product to maintain its good condition. The frequency of cleaning may vary depending on usage, but a general guideline is to clean it at least once a week.

GENERAL GUIDELINES FOR TAP INSTALLATION

AND CARE INSTRUCTIONS

• Before commencing to install the taps & shower please read!!!_ of the following instructions carefully failure to observe these guidelines could invalidate the warranty on the product.
• It is important for optimum performance of the tap that the hot and cold water supplies are balanced.
• Local water authority regulations require that isolating valves are fitted in the pipework beneath the tap to allow the tap to be individually isolated. This makes servicing or replacement of the tap much easier.
• Any warranty claim on the tap will be handled on the basis that isolating valves have been fitted Bath panels MUST be installed so that they can be removed to allow servicing /replacement of the tap and must NOT be tiled in. The panel must be installed AFTER all tiling has been completed.
• Basin wastes should be installed with a bead of silicone to ensure a watertight seal and the rubber washer fitted before the nut. Do NOT over-tighten the nut this could damage the basin and invalidate the warranty.
• Basin wastes may be supplied with rubber washer(s) and it is recommended that where washer(s) are supplied a small bead of silicone is also applied to both sides of the bath before the nut is fitted and tightened. Do NOT over tighten the nut as this could damage the bath and invalidate the warranty.
• Where flexi tails are supplied it is essential that they are NOT over-tightened.
• Once the tap has been installed the water supply should be turned on and the whole installation thoroughly checked for leaks. It is ESSENTIAL that the system is thoroughly flushed to remove any debris or foreign matter which could become lodged under the valve seat and cause dripping or premature failure.
• It is important that tile grout or any aggressive cleaners do not come into contact with the tap and cleaning should be with warm soapy water and the tap thoroughly dried after cleaning.
• Do not exceed the recommended maximum BAR pressure.

Wall Mounted Bath Shower Mixer

Installation and Maintenance Instructions

FITTING YOUR NEW MIXER
Fitting your new mixer is easy when you follow these simple step-by-step instructions.

1. Identify all components.
   

2. IMPORTANT! Rinse out pipework prior to fitting.

3. After having rinsed the pipework. install the valve as a standard exposed fitting, with the hose outlet facing downwards.

4. When connecting the water supply to the valve. it is recommended that the hot supply is to the left and the cold supply to the right with the hose outlet from the botton.

5. Connect the eccentric threaded wall unions to the supply pipes.

6. Ensure that the wall coverings are fitted to the mixer prior to the connection to the water supply.

7. Set the eccentric unions so they correspond with the valves inlets.

8. Fit the mixer to the unions. ensuring to fit the sealing washer, tighten with a spanner until watertight.

9. Turn on the water supply and check for leaks.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS

Whilst modern plating techniques are used in the manufacture of this item. the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Wall Mounted Basin Mixer

FITTING YOUR NEW MIXER
Fitting your new mixer is easy when you follow these simple step-by-step instructions.

1. Identify all components.
   

2. Ensure that the wall cavity or duct is large enough to make all necessary connections. Check that the min/max depth of the cavity is measured from behind the finished surface of the wall.

3. Prior to installation flush out pipework to remove any debris.

4. Connect the water supply and outlet pipework to the valve section and fully tighten the fittings.

5. Connect the outlet pipework from the tap sections to the spout and fully tighten the fittings.

6. Turn on the water supply and test for leaks.

7. If no leaks are found, finish wall plastering and tiling as required.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate ttie guarantee.

Pillar Mounted Bath Shower
Mixer & Bath Filler
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. ”Tap Spanner (‘ may be required. This can be purchased in-store.
2. Ensure the mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Be earful to save and inspect the fibre washer between the base of the tap tails and the water pipe connecting Nut.

Fitting FITTING your new mixer NEW is easy MIXER when you follow these simple step-by-step instructions.

1. Identify all components.

2. Prior to installation flush out pipework to remove debris.

3. Place washers into connecting nuts at rear of body prior to the assembly of pillars.

4. Screw pillars to body ensuring that each pillar is angled outwards (See Fig 1) from the connecting nut to give correct centers to fit on bath. Fully tighten nuts.

5. Place washers onto threaded section of pillars. Insert pillars through holes in the bath.

6. From the underside fit and tighten back nut until mixer is secure. Do not overtighten, otherwise, you risk damage to the bath.

7. Reconnect supply pipes checking that the sealing washers are in good condition (if not replaced). Again do not overtighten. It is recommended.that the hot water supply be connected to the left-hand fitting when installed.

8. Turn on water supply to refill system and check for leaks. If any leaks are noticed. check that the connections are adequately tightened. Once the connections are satisfactory, you can then connect your shower kit (if applicable)

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Mono Sink Mixer

Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. A spanner may be required. This can be purchased in-store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITTING YOUR NEW MIXER

1. Identify all components.
   

2. Prior to installation flush out pipework to remove debris.

3. Screw threaded bar into base of body

4. Place the anti-rotational washer into groove at base of tap body and place the threaded bar through the sink unit.

5. Slide rubber horseshoe washer and metal horseshoe washer over the threaded bar and fix ur.it in place using stud nut. Do not overtighten as it could damage the basin.

6. Connect the copper pipes to the base of tap body and re-connect the hot  and cold water supply taps.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used ,n the manufacture of this item, the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Mono Basin Mixer
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. A spanner may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITTING YOUR NEW MIXER
Fitting your new mixer is easy wtien you follow these simple step-by-step instructions. Please note Tail pipes are supplied as copper tubes or flexible tails. Studs and nuts may vary in number and position depending on range.

1. Identify all components.
2. Prior to installation flush out pipework to remove debris
3. Assemble unit with pop up rod (where applicable), fit the rubber “O” ring to base of mixer and place the fittings through hole m the bath.
4. Screw stud into base of mixer and slide horseshoe washer and plate over Secure with supplied nut. Do not overtighten as ,t could damage the bath.
5. Connect the two tatl pipes to the hot and cold water supplies. Identify all components.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used , in the manufacture of this , tern. the surfaces w,11 wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will , invalidate the guarantee.

Mono Basin/Bidet Mixer
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. A spanner may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITTING YOUR NEW MIXER

Fitting your new mixer is easy wflen you follow these simple step-by-step instructions. Please note Tail pipes are supplied as copper tubes or flexible tails. Studs and nuts may vary in number and position depending on range .

1. Identify all components.
2. Prior to installation flush out pipework to remove debris,
3. Assemble the unit with pop up rod (where applicable). fit the rubber “O” ring to base of a mixer and place the fittings through hole in the bath.
4. Screw stud into base of mixer and slide horseshoe washer and plate over it. Secure with supplied nut. Do not overtighten as it could damage the basin.
5. On models with pop-up wastes, fit waste assembly using a sealant under the pop up flange.
6. Attach pop up rod from the waste to the vertical rod by using the fixing block.
7. Connect the two tail pipes to the hot and cold water supplies.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surfaces will wear ij cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Mono Basin/Bidet Mixer c/w Threaded tail section
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. A spanner may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITTING YOUR NEW MIXER

Fitting your new mixer is easy when you follow these simple step-by-step instructions. Please note Tail pipes are supplied as copper tubes or flexible tails. Studs and nuts may vary in number and position depending on range.

1. identify all components
2. Prior to installation flush out pipework to remove debris.
3. Assemble unit with pop up rod (where applicable), fit rubber “O” ring to base of mixer and place the fittings through hole in the basin.
4. Secure with supplied nut. Do not overtighten as it could damage the basin.
5. On models with pop up wastes, fit waste assembly using a sealant under the pop up flange.
6. Attach pop up rod from the waste to the vertical rod by using the fixing block.
7. Connect the two tail pipes to the hot and cold water supplies. .

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this ,tern. the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Deck Bath Shower Mixers & Deck Bath Filler
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER

1. A “Tap Spanner” may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to the fittings.
5. Be careful to save and inspect the fibre washer between the base of the tap tails and the water pipe.

Atting FITTING your new YOUR mixer NEW is easy MIXER when you follow these simple step-by-step instructions.

1. Identify all components

2. Before installation fully flush out the pipework to prevent any grit lodging on the valve seat inside the top body, as grit will quickly wear the washer.

3. Ensure that the shoulder washer is placed between base of mixer and the fitting surface. Wickes Silicone Sealant may also be used to further seal these items, then carefully position your mixer in place.

4. Screw up the backnut. ensuring that the tap or mixer is in the correct position, taking care not to overtighten this nut as it could damage the bath.

5. Reconnect the supply pipes, checking that the sealing washers are in good condition.
   If not the fibre washers should be replaced.

6. Turn on the taps and water supply at the stopcock or service valves.

7. Your taps are now fitted and ready for use.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surfaces will wear if cleaned incorrectly. Clean th,s product with a soft cloth and clean water. The use of any abrasive material will invahdate the guarantee.

3 Hole Mixers

Fitting FITTING your new YOUR mixer NEW is easy MIXER wflen you follow these simple step-by-step instructions.

Installation and Maintenance Instructions

1. Identify all components
2. Prior to installation flush out pipework to remove debris.
3. Remove handle and shroud cover.
4. Check brass backnut, brass washer then rubber washer is fitted to threaded tail. 5
5. Push tap section through basin hole from underneath and fit second rubber washer to section of tap protruding through basin.
6. Re-fit shroud cover and handle, leave tap section loose at this time.
7. Repeat this procedure for other tap section.
8. Remove spout from spout section. Ensure brass backnut is fitted to threaded tail. Push on brass washer then rubber washer.
9. Push Spout section through basin hole from underneath and fit second rubber washer to section of spout protruding through basin.
10. Reconnect spout to spout section and tighten.
11. Connect pipework between tap section and spout section ensuring sealing washers or olives are fitted correctly.
12. When you are happy with assembly tighten backnuts on taps and spout sections. ensuring to hold tap or spout in the required position.
13. Connect water supply pipes.
14. Insert pop up rod.
15. Fit waste flange into basin using washer provided. sealant may also be used.
16. Connect waste base to underside of waste also using washer provided.
17. Connect pop up rods by using connector.

This product should be fitted in accordance with Water Bylaw Regulations Check valves should be fitted where necessary.

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used in the manufacture of this item, the surfaces will wear if cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material invalidates the guarantee.

Mono Basin/Bidet Mixer
Installation and Maintenance Instructions

REMOVING OLD TAPS OR MIXER (PREL113/PREL114)

1. A spanner may be required. This can be purchased in store.
2. Ensure mains water supply is turned off at the stopcock or service valves.
3. After disconnecting the water supply, drain the pipework.
4. Unscrew the nuts connecting the water pipes to hte fittings.
5. Save and inspect fibre washer for future use.
6. Unscrew backnuts and remove taps.

FITTING YOUR NEW MIXER
Fitting your new mixer is easy wflen you follow these simple step-by-step instructions. Please note Tail pipes are supplied as copper tubes or flexible tails. Studs and nuts may vary in number and position depending on range.

1. Identify all components.
   

2. Prior to installalton flush out pipework to remove debris.

3. Assemble unit with pop up rod (where applicable), fit rubber “O”‘ ring to base of mixer and place the fittings through hole in the basin.

4. Screw stud into base of mixer and slide horseshoe washer and plate over ,t.

5. Secure with supplied nut Do not overtighten as it could damage the basin 5 On models with pop up wastes, fit waste assembly using a sealant under the pop up flange.

6. Attach pop up rod from the waste to the vertical rod by using the ftx,ng block.

7. Connect the two tail pipes to the hot and cold water supplies.

This product shou,d be htted in acco«ianoe with Water Bylaw Regulat10ns Check valves shou,d be htted where necessary

AFTERCARE INSTRUCTIONS
Whilst modern plating techniques are used , in the manufacture of this , tern, the surfaces will wear cleaned incorrectly. Clean this product with a soft cloth and clean water. The use of any abrasive material will invalidate the guarantee.

Maintenance/ Care and Cleaning Instruction

Maintenance and Cleaning Instructions
The finishes of our products are durable. To keep our products in good condition, the end users are required to regularly maintain and clean all the surfaces based on the following guidelines:

• Warm water or mild soapy water should be used to remove system debris and limescale.
• After cleaning, all soapy water should be removed by water and polished with a clean, soft and dry cloth.
• No abrasive cleaning agents or materials should be used.
• No corrosive cleaning agents should be used, which will cause corrosion.
• More care should be taken in hard-water areas to ensure all the surfaces are regularly cleaned.
• Failure to do so will invalidate the product warranty.

Care Instructions

Please be careful when installing, using, cleaning and maintaining this product. Any defects or damages like peeling problem at this product due to the following reasons is not covered by the product warranty:

• incorrect installation.
• accidental or wilful misuse.
• inappropriate cleaning products.
• inadequate maintenance.
• chemical damage caused by system debris and build-up of limescale (any soapy water left on the surface of the product and not cleaned regular will affect the finish of the product.)
• physical damages like scratches.
• damage caused during repair work.
• water quality i.e. rusting water from the pipework need to be fully flushed out after use or water pressure issues.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>