VEVOR BD-HB-50W LED Barn Light User Manual

: June 16, 2024
: VEVOR

Table of Contents

BD-HB-50W LED Barn Light
TECHNIQUE PARAMETER
INSTALLATION INSTRUCTIONS FOR LIGHT CONTROL COMPONENTS
WIRING DIAGRAM
INSTALLATION DIAGRAM
MAINTENANCE INSTUCTION
LIST OF ACCESSORIES
Documents / Resources

LED WALL LIGHT INSTRUCTION
USER’SMANUAL
MODEL: BD-HB-50W/BD-HB-100W

BD-HB-50W LED Barn Light

Technical Support and E-Warranty Certificate www.vevor.com/support
We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us: **CustomerService@vevor.com
** This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

| Warning-To reduce the risk of injury, user must read
instructions manual carefully.
---|---
****| This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.

TECHNIQUE PARAMETER

Input Voltage: AC100-265V 50/60HZ
Rated power: 50W(BD-HB-50W), 100W(BD-HB-100W)
Certificate: IP65, CE, FCC , ROHS.

INSTALLATION INSTRUCTIONS FOR LIGHT CONTROL COMPONENTS

Take out the light control unit, and the plug of the light control unit is aimed at the socket hole of the lamp body (it cannot be inserted if it is not fully aligned).
After alignment, turn clockwise until it cannot rotate, at which point the installation is complete.
Specifications of the photosensitive component

Turn-On Light Levels：10-16 Lux
Time Delay ：3-10 Seconds
Operating： -40℃ to +70℃
Switch： > 5000 ON/OFF Operations at Rated Load
Ingress Protection：IP65

WIRING DIAGRAM

VEVOR BD HB 50W LED Barn Light - WIRING DIAGRAM

INSTALLATION DIAGRAM

VEVOR BD HB 50W LED Barn Light - INSTALLATION DIAGRAM

Blackout before installation.Don’t install it with electricty on.
Adjust the suitable angle.
The lamp body is directly installed on the wall:please close the opening and fix it on the wall with 10mm expansion screws.
Installation with lamp post: use 8mm socket wrench to loosen the screw until the lamp post can be inserted into the lamp cap and pass through the joint, then tighten the screw, and then ﬁx the lamp arm on the wall or lamp post.
Connect the wire. It’s 0.75MM² triple-core, brown is Line of fire, blue is zero line, yellow green is ground line.
After the wiring is completed, turn on the power (this product does not have a power switch, and the user needs to install the control switch by himself); The light control unit starts to work, the light does not light up during the day, and it automatically lights up at night.
Don’t try to install the damaged product.
Don’t install the lamp in the enclosed place in order to have a good heat dissipation effect.
Make sure the wire connection is good and safe to avoid electric leakage after installing the lamp.
Waterproof measures must be taken when connecting the driver.
Don’t violate the law of ﬁre control when using the lamp.
The lamp can be automatically turned on and off according to the intensity of the ambient, and the lamp is automatically turned off during the day and turned on at night.

MAINTENANCE INSTUCTION

Turn off the driver when maintaining the lamp.
Regularly Clean the dust on the heat sink in order to have a good heat dissipation effect.
Don’t use chemical or corrosive liquid to clean the lamp. Please use dry cloth to clean it.
Please contact the dealer and manufacturer if the LED chip or driver has to be replaced. Because the waterproof and dust-proof performance will be effected after dismounting again.