PETLUX PL-18W Automatic Pet Feeder Instruction Manual

PETLUX PL-18W Automatic Pet Feeder

Product Information

Specifications

• Product Name: Automatic Pet Feeder
• Product Model: PL-18W
• Product Size: 204x334x345 mm
• Rated Voltage: 6V DC
• Rated Power: 5W
• Use powerful low-noise DC motor
• Feeder Capacity: 4L/2kg
• Material: SUS304, ABS food-grade plastic

Product Usage Instructions

Precautions for Product Use
Product Cleaning and Environmental Protection:

1. Do not clean the control panel, pet food container, and container holder directly with water flow to avoid internal component damage. It is recommended to clean with a dry cloth.
2. Clean the internal pet food container using a soft cloth with a harmless neutral detergent. The top cover can be cleaned directly with water flow.

Environmental Protection:

1. Do not put the product together with general household garbage when discarding it. Please hand it over to the officially designated recycling center for proper disposal.
2. The battery contains substances that pollute the environment. Do not throw away the host with ordinary household garbage. Instead, hand it over to a formal battery collection point for disposal.

Name of Product Parts

• Top Cover
• Housing
• Detachable Feeding Base
• Feeding Bowl

Fault Analysis and Troubleshooting

together
No feeding at the set feeding time| The network time is not synchronized with the mobile time| Exit the connection, restart the machine, and reset the feeding
plan after the network is normal

Caution:
The above are the common error analysis and troubleshooting methods. For other errors, please contact our customer service department or directly go to our designated maintenance point. Do not disassemble and repair by yourself.

Operation Instructions

1. Power On:
2. Insert the adapter pin into the socket with a DC voltage of 100-240V/50-60Hz.
3. Connect the elbow plug of the adapter to the bottom of the appliance to power it on.
4. Battery Power On:
5. Loosen the screws of the battery cover.
6. Open the battery cover and install four batteries for power.

Please read this product manual carefully before use and keep it properly!

Special note:
All contents of this product manual have been carefully reviewed. In case of any printing errors, omissions or misunderstandings in the content, we reserve the right to revise it without notice and reserve the right of final interpretation.

Thank you for using our pet feeder. We have specially prepared this manual for you to use and maintain this product correctly. Please read this manual carefully before using the product and keep it properly for future reference.

This manual is only applicable to our pet feeders. All contents in the manual are only for users’ reference during use and maintenance. For matters not covered, users are welcome to consult our customer service department. For the deficiencies of this book, you are welcome to put forward your valuable opinions. I hope this product can bring warmth, convenience and health to your life.

Precautions for product use

1. This product uses an adapter or dry battery to power on.
2. The product must be used under a temperature between 3-40°C.
3. Do not immerse the host in water or other liquids, nor wash it under the tap. Clean only with a damp cloth.
4. Please put the machine out of the reach of children.
5. Do not let children use this product without supervision.
6. Do not operate upside down.
7. This product can only be used as a container and cannot be put into the oven.
8. Food grade plastic, dividing plate Storage tray SUS 304 material.
9. This product is only for pets.
10. The feeder needs to be stored correctly when it is not in use, please clean it first and then place it in a dry place. Do not expose it to the sunshine for a long time.

Product cleaning and environmental protection

1. There’s a wire inside the control panel, pet food container and container holder, so it is not allowed to be cleaned it directly with water flow to avoid internal component damage. It is recommended to clean with a dry cloth.
2. It is recommended to clean the internal pet food container by a soft cloth with harmless neutral detergent, and the top cover can be directly cleaned with water flow.

Environmental Protection

1. Please do not put the product together with general household garbage when discarding it; It should be handed over to the officially designated recycling centre, which is conducive to environmental protection.
2. The battery contains substances that pollute the environment. Do not throw away the host with ordinary household garbage, but hand it over to a formal battery collection point for disposal.

Name of product parts

Product electrical parameters

1. Four batteries (not included with the product): 6V
2. Adapter: DC 5.9 V/1A
3. Motor: DC6V RPM:7.5 ± 12% 0.5W

Product performance and specifications

1. Product Name: Automatic Pet Feeder
2. Product model: PL-18W
3. Product size: 204x334x345 mm
4. Rated voltage: 6V DC
5. Rated power: 5W
6. Use powerful low-noise DC motor
7. Feeder capacity: 4L/2kg
8. Material: SUS304, ABS food-grade plastic
9. The feeder can deliver food regularly and quantitatively

Fault analysis and troubleshooting

together

No feeding at the set feeding time

| The network time is not synchronized with the mobile time| Exit the connection, restart the machine, and reset the feeding plan after the network is normal

Caution
The above are the common error analysis and troubleshooting methods. For other errors, please contact our customer service department or directly go to our designated maintenance point. Do not disassemble and repair by yourself.

Operation instructions

1. Power on
2. Insert the adapter pin into the socket with a DC voltage of 100-240V/50-60Hz, and connect the elbow plug of the adapter to the bottom of the appliance for power on. (as shown in Figure 1)
3. Loosen the screws of the battery cover, open the battery cover and install four batteries for power on. (as shown in Figure 1)
4. Operation
5. How to install before use: Tilt the housing about 45°, and place the feeding base just below the edge of the housing. Lower the housing slowly, and make sure the feeding base is secured by the hook of the housing (as shown in Figure 2). Put the feeding bowl into the feeding base.
6. Pet food filling: remove the top cover and put the pet food into the container, and then put the top cover steadily on the box and gently press it in place (as shown in Figure 3 and Figure 4).
7. Switch on: After powering on, the indicator lights up and constantly flashes in a circle.
8. The indicator lights up and constantly flashes in a circle. Click the button once to manually feed one portion of pet food.
9. Once lacking pet food, the indicator light of the ON/OFF button turns red and flashes and there’s an alarmed voice, at the same time the app also has food-lacking displays to remind users to replenish pet food.
10. If there isn’t any operation for 30 seconds after power on, it automatically enters into the child lock mode, press the button for 3 seconds to unlock.
11. Press the button for 5 seconds, and the white indicator light flashes which means the machine is ready for a WiFi connection.

How to connect WiFi and set a feeding plan

Please connect to the WiFi and Open the Bluetooth function from your mobile phone before connection.

• Step 1: Take out the mobile phone, download and install the TUYA/Smart Life APP, then open the APP and click ‘Add Device’ to connect the devices.

• Step 2: Detect the device, then click and add the device. After connecting successfully, the indicator of lights is constant.

• Step 3: Add the device, and click ‘Done’ after adding successfully.

• Step 4: Get into the operation interface, and click ‘Meal Plan’ to set your feeding plan. The feeding schedule can last for 7 days, and portion size is 1-12. After the feeding plan is completed, the appliance is in standby or cycle feeding status.
  Remark:

  • Click the ‘Manual’ button and select a different portion for manual feeding.
  • Click “+” “-” to adjust the number of portions.
  • Click the’ Quick’ button for quick feeding, just one portion for each click.

• Step 5: Click ‘Add’ to add the new feeding plan.
  Notice: The feeding bowl can hold up to 15 portions (about 150g), and the amount of each portion is about 10g.

• Step 6. Remove the power supply to switch off the appliance. At this time, the indicator light of the ON/OFF will turn off.

How to connect WiFi and set a feeding plan

How to connect WiFi and set a feeding plan (Diagram 1)

How to connect WiFi and set feeding plan (Diagram 2)

Name and content of harmful substances in products

This form is drawn up according to the provisions of sj11364.

• ○ Indicates that the content of the hazardous substance in all homogeneous materials of the component is below the limit specified in GB/t26572.
• ╳ Indicates that the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit specified in GB/t26572.

The “environmental protection service life” of this product is 10 years. The environmental protection service life is valid only when the product is used under the correct operation described in this manual.

GUARANTEE CARD

User information

Warranty records

Warranty terms

1. The warranty period of this product is 1 year from the date of sale.
2. We will provide you with high-quality after-sales service.
3. If the product is damaged due to incorrect human operations, we will charge maintenance fees when repairing.
4. Please keep this card properly, and we will keep it as the basis.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>