SWIT FLOW2000Tx SDI & HDMI Transmission System User Manual

SWIT FLOW2000Tx SDI & HDMI Transmission System User Manual

Preface

• All internal technologies ofthi5 product are protected, including device, software and trademark.
  Reproduction in whole or in part without written permission is prohibited.

• All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners.

• Due to constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice.

The warranty period of this product is one years, and does not cover the following:

1. Physical damage to the products
2. Any damage or breakdown caused by use, maintenance, or storage not according to the user manual’ 5 introductions.
3. The attenuation ofsignal quality resulting from being used in any special environments.
4. Any damage caused by not powering the product by package supplied power adaptor.
5. Any damage or breakdown not caused by the prodUCt’ 5 design, workmanship, manufacturing, quality, or unauthorized repairs or parts replacement or other operations.

For any suggestions and requirements on this prodUCt5, please contact us, please contact U5 through phone, fax, Email, etc.

SWIT Electronics Co., Ltd.

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R.China
Phone: +86-25-85805753
Fax: +86-25-85805296
Email: contact@swit.cc
http://www.swit.cc

Safety Precautions

Please follow the safety precautions before using. The following conditions are not covered by warranty.

1. Unauthorized repairs or other Unauthorized operations.
2. Inappropriate placement including but not limited to lighting, fire, exposure to rain, water or gas.
3. Using the wrong power supply.

Warning

• Do not get any liquid inside the products
• Do not block the ventilation openings or put substances inside, in order to avoid short circuit, fire or electric shock.
• Do not place the product in the rain or moisture to avoid electric shock or fire.

Danger

• Switch the power off before connecting other devices.
• Power socket: Make sure the power socket under the voltage range of the product to avoid short circuit, electric shock and fire.
• Power cable: Make sure the power cable is not pressed or tightened by any items or weights.
• Power Load: Do not exceed the load on the wall outlet, extension cable or other porous receptacle to avoid fire or electric shock.
• Lightning: Disconnect the power cable if it is lightning or not using in a long period of time.

Working environment

• Please don’t lay the product on any unstable place to avoid fatten damage.
• Please don’ t use the product in a place overheating, under cooling or with tots of moisture, or near by strong magnetic devices.
• Please don’ tlay the product on metal shelf, in order to ensure the effective wireless transmission.

Packing List

This wireless system includes below accessories:

Product Introduction

FLOW2000 includes transmitter and receiver, adopts the latest encrypted transmission technology, Supports SDI and HDMI Wireles5ly transmitted in 600 meters Scale (Line-of-Sight), 2 channels SDI/HDMI digital video transmission, auto pairing and OLED display. FLOW2000 is equipped with DC power connector, compact size, portable, and the receiving signal is very stable.

Features

• 3G/HD/SD-SDI and HDMI transmission
  Support up to 1080p 50/60Hz SDI & HDMI wireless transmission.

• 600 meters transmission distance.
  In open outdoor area, the effective transmission distance is approx. 600 meters (line of sight)

• Wireless frequency
  The system adopts 5180 5220MHz and 5760 5820MHz Wireless frequency band (FLOW2000 Tx) . Frequency Band and Frequency Point

  CH00| 5180MHz| CH04| 5780MHz
  CH01| 5200MHz| CH05| 5800MHz
  CH02| 5220MHz| CH06| 5820MHz
  CH03| 5T60MHz| /| /

• Pairing mode
  Support auto pairing connection and manual switching of frequency points. Support one transmitter to multi-recevier mode.
  

• OLED Display
  Display the current working parameter, such as signal format, wireless channel, signal strength, and so on.

• High quality & Wall through mode Support I transmitter to unlimited receivers and High quality & Wall through mode Choose.

The system adopts 5182.5 5282.5MHz and 5762.5 5822.5MHz Wireless frequency band (FLOW2000 Rx) .

Frequency Band and Frequency Point

CH00| 5180MHz| CH04| 5780MHz
CH01| 5200MHz| CH05| 5800MHz
CH02| 5220MHz| CH06| 5820MHz
CH03| 5T60MHz| /| /

• Encryption
  Support AES 128-bit encryption to protect the transmission.

• All-Metal SheIl
  BOth the transmitter and receiver adopt metal shell which is durable and solid.

• All hardware design
  The wireless system is hardware and plug-and-play designed, without installing Software, easy to set upon

• Multiple battery plates change
  Transmitter can choose different battery plate according to demand.

Remark:

1. The transmission distance may be different, and depend on surroundings, radio wave conditions, buildings, etc., the 600 meters transmission distance may be not guaranteed.
2. The wireless transmission might be interrupted if there’ re other devices of5GHz wireless bandwidth Used in the same location.
3. Signal reception may be affected by the position, height and angle of devices. If reception video i5 not Stable, please physically adjust placement for the optimized signal.
4. Set the antennas straight up and set receiver higher to enhance the transmission efficiency.

Appearance instruction

Transmitter FLOW2000

1. Antenna
2. Product label
3. Link: Wireless status indicator
4. Video: Video signal indicator
5. Power: Power status indicator
6. OLED: 0.96-inch OLED
7. Five-direction switch: Five-direction adjustment button (adjust the display menu to switch and confirm in five directions: up, down, left, right, and vertical)
8. Installation thread: 1/4”-20 thread. Use the package supplied articulating arm trestle to install the device to the camera.
9. USB: Micro USB, software upgrade interface
10. HDMI in: HDMI input (HDMI-A type connector)
11. Battery plate: Power supply via D & F & U model battery plate. Model D battery we recommend SWIT battery: S-8D98. S-8D58 S-8D62 which is compatible with Panasonic CGA series ;CGA-D54S/D28S.VBD series SVW-VBD58; Model F battery we recommend SWIT battery: S8972› S-8970. S-8770. S-8975, which is compatible with SONY L series NP-F770/970; Model U battery we recommend SWIT battery LB-SU98, , which is compatible with PXW-FX series BP-U60/U30/U90.
12. SDI LOOP: SDI Loop out (BNC connector)
13. SDI in: SDI input (BNC connector)
14. ON/OFF: Power switch
15. DC in : Support DC 7-34V voltage input, 5.5mm (outer diameter) /2.1mm (inner diameter). Outside: negative, Inside: positive

The description of LED status indicator

FLOW2000
Transmitter| Power| Constant On| Power connected and switched on
or| Power disconnected and switched off
Video| Constant On| There is recognizable video signal input
Flash| There is no recognizable video signal input
Link| Constant On| The wireless network connection is normal
Flash| The wireless network connection is abnormal

Receiver FLOW2000

1. Antenna
2. ON/OFF: Power switch
3. USB: Micro USB, sokware upgrade interface
4. Link: Wireless status indicator
5. Video: Video signal indicator
6. Power: Power status indicator
7. DC in: Support DC 7-34VvoItage input, 5.5mm (outer diameter) /2.1mm (inner diameter). Outside: negative, Inside: positive
8. OLED: 0.96-inch OLED
9. Five-direction switch: Five-direction adjustment button. (adjust the display menu to switch and con firm in five directions up, down, left,right, and vertical)
10. Installation thread: 1/4” -20 thread, Use the package supplied articulating arm trestle to install the device to the camera
11. HDMI OUT: HDMI output (HDMI-A type connector)
12. SDI out: SDI output (BNC connector)
13. Battery plate: Power supply via D & F & U model battery plate. Model D battery we recommend SWIT battery: S-8D98.S-8D58.S-8D62 which is compatible with Panasonic CGA series;CGA-D54S/D28S. VBD series SVW-VBD58; Model F battery we recommend SWIT battery: S-8972.S-89T0.S-87T0.
    S-8975, which is compatible with SONY L series NP-F770/970; Model U battery we recommend SWIT battery LB-SU98, which is compatible with PXW-FX series BP-U60/U30/U90

The description of LED status indicator

OLED Display menu

Initial interface (One-to-one mode)
When no signal input, the transmitter is consistent with the receiver display content. See Fig. 1

Initial interface (One-to-one mode)
When Transmitter and receiver video signal connection normal, the transmitter is consistent with the receiver display content. See Fig. 2

Initial interface (One-to-multi mode)
When the transmitter has no signal input, see Fig. 3

Initial interface (One-to-multi mode)
When the transmitter video signal is connected normally, as shown in Fig. 4

Initial interface (One-to-multi mode)
When the receiver has no signal input, see Fig. 5

Initial interface (One-to-multi mode)
When the receiver video signal is connected normally, as shown in Fig. 6

Tips:

1. Using joy stick(up and down) to change frequency channel,7 channel in total.
2. After changing to one-to-multi mode, There will be a “M” show on the bottom

Interface changing

• Changing interface in transmitter via using joystick(left and right),see fig .7.8.9.
• Changing interface in receiver via using joystick(left and right),see fig .7.9.
  
  
  

Tips:

1. The menu content of transmitter and receiver is different: Quality mode and wall through mode can only be selected in transmitter, see fig.8
2. The“MULTI CAST” should change to“ON” in both transmitter and receiver to open one-to-multi mode.(Both transmitter and receiver need to choose “MULTICAST ON”)
3. Support firmware upgrading via USB interface.
4. Both transmitter and receiver support manually switch frequency channel.
5. Factory setting is “MULTICAST OFF”.
6. Choose “MULTICAST ON”(The transmitter need to pair with every receiver before using one-to-mufti mode)

Pairing

1. Switch on both FLOW2000 transmitter and receiver; The “POWER” indicator fight in every receiver should light up when there are multiple receiver, Waiting for jumping to main interface.
2.  Right pushing the joystick to “PAIR” interface and choose “YES” in both transmitter and receiver, the“LINK”indicator flashing quickly during pairing(Every receiver should pair with the transmitter separately when using one-to-multi mode) .
3. “LINK” indicator will stop flashing after pairing successful. Device in encrypted transmission state.

Tips:

1. Transmitter and receiver should pair in the same time. Every receiver should be paired with the transmitter separately when using one-to-multi mode.
2. Make sure every receiver have already paired successful before using one-to-multi mode.
3. The paired receiver and transmitter, automatically connected after boot, no need to pair again.
4. Keep 1-2 m distance between transmitter and receiver when pairing to avoid pairing failure.
5. Do not using more than 4 group wireless transmission device to avoid disturbing

Connection

1. Connecting SDI IN/HDMI IN interface of FLOW2000 transmitter with SDI OUT/HDMI OUT interface of camera or video output device. Connecting SDI loop out interface of FLOW2000 transmitter with SDI IN interface of monitor or switcher.

2. Connecting SDI OUT interface of FLOW2000 receiver with SDI IN interface of monitor or 5Witcher.
   When using one-to-multi mode, every SDI OUT interface of receiver should be connected with SDI IN interface of monitor orswitcher.

3. Switch on both FLOW2000 transmitter and receiver, “Power”indicator light up, OLED screen show“WAlT…“then jump to initial interface, see fig.1 or fig.3;Wait until “Link” and “Video” indicator light up, the transmitter and receiver have identifiable signal inputs and connected successfully. If the transmitter and receiver have identifiable signal inputs but fail to establish a connection, the “link” indicator will flash.

Tips:

1. After powering the FLOW2000 transmitter and receiver, dial the power switch on the product to “on””
2. FLOW2000 transmitter support SDI video signal input and HDMI video signal input, the System automatically identify input video interfaces. System will choose SDI video Signal when both HDMI and SDI interface is connected.
3. When multiple receivers are used simultaneously in the same environment, ensure that multiple wireless devices have identifiable Signal input.

High quality mode & Wall through mode

1. Connecting SDI IN/HDMI IN interface of FLOW2000 with SDI OUT/HDMI OUT interface of camera or video output device. Connecting SDI loop out interface of FLOW2000 transmitter with SDI IN interface of monitor or switcher.

2. When using one-to-multi mode, every SDI OUT interface of receiver should be connected with SDI IN interface of monitor orswitcher.

3. Switch on both FLOW2000 transmitter and receiver, every receiver should be switch on when using one-to-multi mode. “Power”indicator light up, OLED screen show“WAlT…”then jump to initial interface, see fig.1 or fig.3;Wait until “Link” and “Video” indicator light up, the transmitter and receiver have identifiable Signal inputs and connected successfully, right push the joystick to“PREF”interface, See fig.11.
   

4. It is recommended to choose high quality mode for wireless devices under normal operating conditions, such as better environment, stronger signal, or more than one set of wireless devices under the same scene.

5. Wall through mode is recommended for wireless devices under complex operating conditions, such as poor on-site environments, high distance barriers and only 1-2 sets of wireles5 devices in the same scene.
   (If more than one set is used in the same scene, it is recommended to use a high quality mode to reduce interaction)

Tips:

1. When wireless devices under normal operating condition, choose High quality mode can get a better video quality, but transmission distance will be cut.
2. When wireless devices under complex operating condition, choose Wall through mode can get a long transmission distance, but the video quality will be cut.

The way to get the best effective of wireless Transmission

1. Set the antenna on both transmitter and receiver vertically straight up.(See Fig.12), Set the receiver faces the transmitter to extend the transmission distance and stabilize the transmission quality.
   

2. Set the receiver as high as possible to avoid interference.
   

3. Avoid walls, trees and water.
   

Troubleshooting

If the receiver failed to output video correctly, the possible causes are as below; please find the solution from following chart:

and switch on the transmitter and receiver
The antennas are not installed properly and screwed tightly| Install the antennas properly and screw tightly of both transmitter and receiver
Bad connection of video cable| Check video cable connection of both transmitter and receiver
Video format is not supported| Change the output video format of the camera
Poor Video quality| Bad connection with video cable| Reconnect reliably
The wireless transmission is disturbed by environment| Wait for 1 minute or reboot the transmitter and receiver
The transmission distance is out of effective range| Close the transmitter to the receiver

Specification

(60/59.94/50/30/29.97/25/24/23.98)

Wireless frequency| 5.17GHz-5.23GHz and 5.75GHz-5.83GHz
modulation mode| OFDM Support 16QAM, 64QAM, QPSK, BPSK modulation mode
transmission distance| 600m (Line of sight)
Power consumption| <8W| <8W
Transmitting power| Max CE:25mW      FCC:50mW| /
Human—Machine Interaction| 0.96-inch OLED, Five-direction adjustment button
Input voltage| DC/ Battery:7     34V| DC/ Battery :7     34V
Working environment| Temperature :0°C +40°C
Dimension(without antenna and plate)| 66+ 106.5X 24.7 (mm)| 106.5+66+24.7(mm)
Net weight (without antenna)| 236.0g| 245.0g

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>